reorder struct hrtimer to save 8 bytes on 64 bit builds when
CONFIG_TIMER_STATS selected. (also removes 8 bytes from signal_struct)
Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The hotplug notification handler and drivers' notification handler all
run in one workqueue. Before hotplug removes an acpi device, the
device driver's notification handler is already be recorded to run just
after global notification handler. After hotplug notification handler
runs, acpica will notice a NULL notification handler and crash.
So now we run run hotplug in another workqueue and wait
for all acpi notication handlers finish.
This was found in battery hotplug, but actually all
hotplug can be affected.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The battery driver already registers notification handler.
To avoid registering notification handler again,
introduce a notifier chain in global system notifier handler
and use it in dock driver.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When we use > 4KB's page size the original definition is not consistent
with PGDIR_SIZE. For exeample, if we use 16KB page size the PGDIR_SHIFT is
(14-2) + 14 = 26, PGDIR_SIZE is 2^26，so the PTRS_PER_PGD should be:
2^32/2^26 = 2^6
but the original definition of PTRS_PER_PGD is 4096 (PGDIR_ORDER = 0).
So, this definition needs to be consistent with the PGDIR_SIZE.
And the new definition is consistent with the PGD init in pagetable_init().
Signed-off-by: Dajie Tan <jiankemeng@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: fix build error in !oneshot case
x86: c1e_idle: don't mark TSC unstable if CPU has invariant TSC
x86: prevent C-states hang on AMD C1E enabled machines
clockevents: prevent mode mismatch on cpu online
clockevents: check broadcast device not tick device
clockevents: prevent stale tick_next_period for onlining CPUs
x86: prevent stale state of c1e_mask across CPU offline/online
clockevents: prevent cpu online to interfere with nohz
This is not generic enough, added here for backward compatibility.
And make this an individual commit so future revert will be a bit
easier.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The driver is based on different source files including corgi_ssp.c,
corgi_lcd.c and corgi_bl.c, previously authored by Richard Purdie
and many others.
The LCD and Backlight device actually share the same SPI device, so
they are made into this single driver.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some LCD panels are capable of different resolutions, and is allowed
to change at run-time, so to make "struct lcd_device" to be able to
handle mode change events here.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
linux/time.h conflicts with time.h from glibc
It breaks building smbmount from samba. It's regression introduced by
commit 76308da (" smb.h: uses struct timespec but didn't include
linux/time.h").
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: <stable@kernel.org> [2.6.26.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the second resubmission of the posix timer rework patch, posted
a few days ago.
This includes the changes from the previous resubmittion, which addressed
Oleg Nesterov's comments, removing the RCU stuff from the patch and
un-inlining the thread_group_cputime() function for SMP.
In addition, per Ingo Molnar it simplifies the UP code, consolidating much
of it with the SMP version and depending on lower-level SMP/UP handling to
take care of the differences.
It also cleans up some UP compile errors, moves the scheduler stats-related
macros into kernel/sched_stats.h, cleans up a merge error in
kernel/fork.c and has a few other minor fixes and cleanups as suggested
by Oleg and Ingo. Thanks for the review, guys.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently a SIGTRAP can denote any one of below reasons.
- Breakpoint hit
- H/W debug register hit
- Single step
- Signal sent through kill() or rasie()
Architectures like powerpc/parisc provides infrastructure to demultiplex
SIGTRAP signal by passing down the information for receiving SIGTRAP through
si_code of siginfot_t structure. Here is an attempt is generalise this
infrastructure by extending it to x86 and x86_64 archs.
Signed-off-by: Srinivasa DS <srinivasa@in.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: akpm@linux-foundation.org
Cc: paulus@samba.org
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Combine both generic and arch-specific parts of microcode into a
single module (arch-specific parts are config-dependent).
Also while we are at it, move arch-specific parts from microcode.h
into their respective arch-specific .c files.
Signed-off-by: Dmitry Adamushko <dmitry.adamushko@gmail.com>
Cc: "Peter Oruba" <peter.oruba@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: System hang when AMD C1E machines switch into C2/C3
AMD C1E enabled systems do not work with normal ACPI C-states
even if the BIOS is advertising them. Limit the C-states to
C1 for the ACPI processor idle code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: hang which happens across CPU offline/online on AMD C1E systems.
When a CPU goes offline then the corresponding bit in the broadcast
mask is cleared. For AMD C1E enabled CPUs we do not reenable the
broadcast when the CPU comes online again as we do not clear the
corresponding bit in the c1e_mask, which keeps track which CPUs
have been switched to broadcast already. So on those !$@#& machines
we never switch back to broadcasting after a CPU offline/online cycle.
Clear the bit when the CPU plays dead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current check wrongly uses the state of one (currently the first)
tx queue for all tx queues in case of non-default qdiscs. This check
mainly prevented requeuing loop with __netif_schedule(), but now it's
controlled inside __qdisc_run(), while dequeuing. The wrongness of
this check was first noticed by Herbert Xu.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lot of code wants to iterate over an SKB queue at the top level using
it's own control structure and iterator scheme.
Provide skb_queue_next(), which is only valid to invoke if
skb_queue_is_last() returns false.
Signed-off-by: David S. Miller <davem@davemloft.net>
Several bits of code want to know "is this the last SKB in
a queue", and all of them implement this by hand.
Provide an common interface to make this check.
Signed-off-by: David S. Miller <davem@davemloft.net>
ASoC and non-ASoC drivers for PCM DMA on PXA share lots of common code.
Move it to pxa2xx-lib.
[Fixed some checkpatch warnings -- broonie]
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
ASoC and non-ASoC drivers for ACLINK on PXA share lot's of common code.
Move all common code into separate module snd-pxa2xx-lib.
[Fixed handing of SND_AC97_CODEC in Kconfig and some checkpatch warnings
-- broonie]
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Handle the case of head being non-empty, by adding list->qlen
to head->qlen instead of using direct assignment.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for keeping an additional character alias
associated with an network interface. This is useful for maintaining
the SNMP ifAlias value which is a user defined value. Routers use this
to hold information like which circuit or line it is connected to. It
is just an arbitrary text label on the network device.
There are two exposed interfaces with this patch, the value can be
read/written either via netlink or sysfs.
This could be maintained just by the snmp daemon, but it is more
generally useful for other management tools, and the kernel is good
place to act as an agreed upon interface to store it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no listener socket for a received packet, send an error
back to the sender.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phonet endpoints are bound to individual ports.
This provides a /proc/sys/net/phonet (or sysctl) interface for
selecting the range of automatically allocated ports (much like the
ip_local_port_range with IPv4).
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides support for configuring Phonet addresses, notifying
Phonet configuration changes, and dumping the configuration.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides support for adding Phonet addresses to and removing
Phonet addresses from network devices.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the basis for the Phonet protocol families, and introduces
the ETH_P_PHONET packet type and the PF_PHONET socket family.
Signed-off-by: Remi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As discovered by Timo Teräs, the currently xfrm_state_walk scheme
is racy because if a second dump finishes before the first, we
may free xfrm states that the first dump would walk over later.
This patch fixes this by storing the dumps in a list in order
to calculate the correct completion counter which cures this
problem.
I've expanded netlink_cb in order to accomodate the extra state
related to this. It shouldn't be a big deal since netlink_cb
is kmalloced for each dump and we're just increasing it by 4 or
8 bytes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea is to add this to printk after the severity:
printk(KERN_ERR FW_BUG "This is not our fault, BIOS developer: fix it by
simply add ...\n");
If a Firmware issue should be hidden, because it is
work-arounded, but you still want to see something popping up e.g.
for info only:
printk(KERN_INFO FW_INFO "This is done stupid, we can handle it,
but it should better be avoided in future\n");
or on the Linuxfirmwarekit to tell vendors that they did something
stupid or wrong without bothering the user:
printk(KERN_INFO FW_BUG "This is done stupid, we can handle it,
but it should better be avoided in future\n");
Some use cases:
- If a user sees a [Firmware Bug] message in the kernel
he should first update the BIOS before wasting time with
debugging and submiting on old firmware code to mailing
lists.
- The linuxfirmwarekit (http://www.linuxfirmwarekit.org)
tries to detect firmware bugs. It currently is doing that
in userspace which results in:
- Huge test scripts that could be a one liner in the kernel
- A lot of BIOS bugs are already absorbed by the kernel
What do we need such a stupid linuxfirmwarekit for?
- Vendors: Can test their BIOSes for Linux compatibility.
There will be the time when vendors realize that the test utils
on Linux are more strict and using them increases the qualitity
and stability of their products.
- Vendors: Can easily fix up their BIOSes and be more Linux
compatible by:
dmesg |grep "Firmware Bug"
and send the result to their BIOS developer colleagues who should
know what the messages are about and how to fix them, without
the need of studying kernel code.
- Distributions: can do a first automated HW/BIOS checks.
This can then be done without the need of asking kernel developers
who need to dig down the code and explain the details.
Certification can/will just be rejected until
dmesg |grep "Firmware Bug" is empty.
- Thus this can be used as an instrument to enforce cleaner BIOS
code. Currently every stupid Windows ACPI bug is
re-implemented in Linux which is a rather unfortunate situation.
We already have the power to avoid this in e.g. memory
or cpu hot-plug ACPI implementations, because Linux certification
is a must for most vendors in the server area.
Working towards being able to do that in the laptop area
(vendors are starting to look at Linux here also and will use this tool)
is the goal. At least provide them a tool to make it as easy
for this guys (e.g. not needing to browse kernel code) as possible.
- The ordinary Linux user: can go into the next shop, boots the
firmwarekit on his most preferred machines. He chooses one without
BIOS bugs. Unsupported HW is ok, he likes to try out latest projects
which might support them or likes to dig on it on his own, but he
hates to workaround broken BIOSes like hell.
I double checked with the firmwarekit.
There they have:
So the mapping generally is (also depending on how likely the BIOS is
to blame, this could sometimes be difficult):
FW_INFO = INFO
FW_WARN = WARN
FW_BUG = FAIL
For more info about the linuxfirmwarekit and why this is needed
can be found here:
http://www.linuxfirmwarekit.org
While severity matches with the firmwarekit, it might be tricky
to hide messages from the user.
E.g. we recently found out that on HP BIOSes negative temperatures
are returned, which seem to indicate that the thermal zone is
invalid.
We can work around that gracefully by ignoring the thermal zone
and we do not want to bother the ordinary user with a frightening
message: Firmware Bug: thermal management absolutely broken
but want to hide it from the user.
But in the linuxfirmwarekit this should be shown as a real
show stopper (the temperatures could really be wrong,
broken thermal management is one of the worst things
that can happen and the BIOS guys of the machine must
implement this properly).
It is intended to do that (hide it from the user with
KERN_INFO msg, but still print it as a BIOS bug) by:
printk(KERN_INFO FW_BUG "Negativ temperature values detected.
Try to workarounded, BIOS must get fixed\n");
Hope that works out..., no idea how to better hide it
as printk is the only way to easily provide this functionality.
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch against tip/x86/iommu virtually reverts
2842e5bf31. But just reverting the
commit breaks AMD IOMMU so this patch also includes some fixes.
The above commit adds new two options to x86 IOMMU generic kernel boot
options, fullflush and nofullflush. But such change that affects all
the IOMMUs needs more discussion (all IOMMU parties need the chance to
discuss it):
http://lkml.org/lkml/2008/9/19/106
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
"export iommu_area_reserve helper funciton" patch converted all the
users of set_bit_string, GART, Calgary and AMD IOMMU drivers, to use
iommu_area_reserve helper function. Now we can remove unused
set_bit_string function.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There's a small window when NMI watchdog is being set up that if any NMIs
are triggered, the NMI code will make make use of not initalized wd_ops
elements:
void setup_apic_nmi_watchdog(void *unused)
{
if (__get_cpu_var(wd_enabled))
return;
/* cheap hack to support suspend/resume */
/* if cpu0 is not active neither should the other cpus */
if (smp_processor_id() != 0 && atomic_read(&nmi_active) <= 0)
return;
switch (nmi_watchdog) {
case NMI_LOCAL_APIC:
/* enable it before to avoid race with handler */
--> __get_cpu_var(wd_enabled) = 1;
--> if (lapic_watchdog_init(nmi_hz) < 0) {
(...)
asmlinkage notrace __kprobes void default_do_nmi(struct pt_regs *regs)
{
(...)
if (nmi_watchdog_tick(regs, reason))
return;
(...)
notrace __kprobes int
nmi_watchdog_tick(struct pt_regs *regs, unsigned reason)
{
(...)
if (!__get_cpu_var(wd_enabled))
return rc;
switch (nmi_watchdog) {
case NMI_LOCAL_APIC:
rc |= lapic_wd_event(nmi_hz);
(...)
int lapic_wd_event(unsigned nmi_hz)
{
struct nmi_watchdog_ctlblk *wd = &__get_cpu_var(nmi_watchdog_ctlblk);
u64 ctr;
--> rdmsrl(wd->perfctr_msr, ctr);
and wd->*_msr will be initialized on each processor type specific setup, after
enabling NMIs for PMIs. Since the counter was just set, the chances of an
performance counter generated NMI is minimal, but any other unknown NMI would
trigger the problem. This patch fixes the problem by setting everything up
before enabling performance counter generated NMIs and will set wd_enabled
using a callback function.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Acked-by: Don Zickus <dzickus@redhat.com>
Acked-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
x86 has set_bit_string() that does the exact same thing that
set_bit_area() in lib/iommu-helper.c does.
This patch exports set_bit_area() in lib/iommu-helper.c as
iommu_area_reserve(), converts GART, Calgary, and AMD IOMMU to use it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
