This patch removes the selection of AT91_USE_OLD_CLK when selecting at91rm9200
SoC support. This will automatically enable COMMON_CLK_AT91 option and add
support for at91 common clk implementation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull ARM fixes from Russell King:
"Another round of ARM fixes. The largest change here is the L2 changes
to work around problems for the Armada 37x/380 devices, where most of
the size comes down to comments rather than code.
The other significant fix here is for the ptrace code, to ensure that
rewritten syscalls work as intended. This was pointed out by Kees
Cook, but Will Deacon reworked the patch to be more elegant.
The remainder are fairly trivial changes"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8087/1: ptrace: reload syscall number after secure_computing() check
ARM: 8086/1: Set memblock limit for nommu
ARM: 8085/1: sa1100: collie: add top boot mtd partition
ARM: 8084/1: sa1100: collie: revert back to cfi_probe
ARM: 8080/1: mcpm.h: remove unused variable declaration
ARM: 8076/1: mm: add support for HW coherent systems in PL310 cache
On the syscall tracing path, we call out to secure_computing() to allow
seccomp to check the syscall number being attempted. As part of this, a
SIGTRAP may be sent to the tracer and the syscall could be re-written by
a subsequent SET_SYSCALL ptrace request. Unfortunately, this new syscall
is ignored by the current code unless TIF_SYSCALL_TRACE is also set on
the current thread.
This patch slightly reworks the enter path of the syscall tracing code
so that we always reload the syscall number from
current_thread_info()->syscall after the potential ptrace traps.
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 1c2f87c (ARM: 8025/1: Get rid of meminfo) changed find_limits
to use memblock_get_current_limit for calculating the max_low pfn.
nommu targets never actually set a limit on memblock though which
means memblock_get_current_limit will just return the default
value. Set the memblock_limit to be the end of DDR to make sure
bounds are calculated correctly.
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The CFI mapping is now perfect so we can expose the top block, read only.
There isn't much to read, though, just the sharpsl_params values.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reverts commit d26b17edaf
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
Unfortunately the detection was challenged on the defective unit used for tests:
one of the NOR chips did not respond to the CFI query.
Moreover that bad device needed extra delays on erase-suspend/resume cycles.
Tested personally on 3 different units and with feedback of two other users.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sync_phys variable has been replaced by link time computation in
mcpm_head.S before the code was submitted upstream.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a PL310 cache is used on a system that provides hardware
coherency, the outer cache sync operation is useless, and can be
skipped. Moreover, on some systems, it is harmful as it causes
deadlocks between the Marvell coherency mechanism, the Marvell PCIe
controller and the Cortex-A9.
To avoid this, this commit introduces a new Device Tree property
'arm,io-coherent' for the L2 cache controller node, valid only for the
PL310 cache. It identifies the usage of the PL310 cache in an I/O
coherent configuration. Internally, it makes the driver disable the
outer cache sync operation.
Note that technically speaking, a fully coherent system wouldn't
require any of the other .outer_cache operations. However, in
practice, when booting secondary CPUs, these are not yet coherent, and
therefore a set of cache maintenance operations are necessary at this
point. This explains why we keep the other .outer_cache operations and
only ->sync is disabled.
While in theory any write to a PL310 register could cause the
deadlock, in practice, disabling ->sync is sufficient to workaround
the deadlock, since the other cache maintenance operations are only
used in very specific situations.
Contrary to previous versions of this patch, this new version does not
simply NULL-ify the ->sync member, because the l2c_init_data
structures are now 'const' and therefore cannot be modified, which is
a good thing. Therefore, this patch introduces a separate
l2c_init_data instance, called of_l2c310_coherent_data.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull x86 fixes from Peter Anvin:
"A pile of fixes related to the VDSO, EFI and 32-bit badsys handling.
It turns out that removing the section headers from the VDSO breaks
gdb, so this puts back most of them. A very simple typo broke
rt_sigreturn on some versions of glibc, with obviously disastrous
results. The rest is pretty much fixes for the corresponding fallout.
The EFI fixes fixes an arithmetic overflow on 32-bit systems and
quiets some build warnings.
Finally, when invoking an invalid system call number on x86-32, we
bypass a bunch of handling, which can make the audit code oops"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi-pstore: Fix an overflow on 32-bit builds
x86/vdso: Error out in vdso2c if DT_RELA is present
x86/vdso: Move DISABLE_BRANCH_PROFILING into the vdso makefile
x86_32, signal: Fix vdso rt_sigreturn
x86_32, entry: Do syscall exit work on badsys (CVE-2014-4508)
x86/vdso: Create .build-id links for unstripped vdso files
x86/vdso: Remove some redundant in-memory section headers
x86/vdso: Improve the fake section headers
x86/vdso2c: Use better macros for ELF bitness
x86/vdso: Discard the __bug_table section
efi: Fix compiler warnings (unused, const, type)
Pull MIPS fixes from Ralf Baechle:
"This is dominated by a large number of changes necessary for the MIPS
BPF code. code. Aside of that there are
- a fix for the MSC system controller support code.
- a Turbochannel fix.
- a recordmcount fix that's MIPS-specific.
- barrier fixes to smp-cps / pm-cps after unrelated changes elsewhere
in the kernel.
- revert support for MSA registers in the signal frames. The
reverted patch did modify the signal stack frame which of course is
inacceptable.
- fix math-emu build breakage with older compilers.
- some related cleanup.
- fix Lasat build error if CONFIG_CRC32 isn't set to y by the user"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (27 commits)
MIPS: Lasat: Fix build error if CRC32 is not enabled.
TC: Handle device_register() errors.
MIPS: MSC: Prevent out-of-bounds writes to MIPS SC ioremap'd region
MIPS: bpf: Fix stack space allocation for BPF memwords on MIPS64
MIPS: BPF: Use 32 or 64-bit load instruction to load an address to register
MIPS: bpf: Fix PKT_TYPE case for big-endian cores
MIPS: BPF: Prevent kernel fall over for >=32bit shifts
MIPS: bpf: Drop update_on_xread and always initialize the X register
MIPS: bpf: Fix is_range() semantics
MIPS: bpf: Use pr_debug instead of pr_warn for unhandled opcodes
MIPS: bpf: Fix return values for VLAN_TAG_PRESENT case
MIPS: bpf: Use correct mask for VLAN_TAG case
MIPS: bpf: Fix branch conditional for BPF_J{GT/GE} cases
MIPS: bpf: Add SEEN_SKB to flags when looking for the PKT_TYPE
MIPS: bpf: Use 'andi' instead of 'and' for the VLAN cases
MIPS: bpf: Return error code if the offset is a negative number
MIPS: bpf: Use the LO register to get division's quotient
MIPS: mm: uasm: Fix lh micro-assembler instruction
MIPS: uasm: Add SLT uasm instruction
MIPS: uasm: Add s3s1s2 instruction builder
...
Kconfig doesn't select CRC32 so it's possible to build a Lasat kernel
without CONFIG_CRC32 resulting in a build error:
LD vmlinux
arch/mips/built-in.o: In function `lasat_init_board_info':
(.text+0x22c): undefined reference to `crc32_le'
arch/mips/built-in.o: In function `lasat_write_eeprom_info':
(.text+0x7fc): undefined reference to `crc32_le'
make: *** [vmlinux] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Previously, the lower limit for the MIPS SC initialization loop was
set incorrectly allowing one extra loop leading to writes
beyond the MSC ioremap'd space. More precisely, the value of the 'imp'
in the last loop increased beyond the msc_irqmap_t boundaries and
as a result of which, the 'n' variable was loaded with an incorrect
value. This value was used later on to calculate the offset in the
MSC01_IC_SUP which led to random crashes like the following one:
CPU 0 Unable to handle kernel paging request at virtual address e75c0200,
epc == 8058dba4, ra == 8058db90
[...]
Call Trace:
[<8058dba4>] init_msc_irqs+0x104/0x154
[<8058b5bc>] arch_init_irq+0xd8/0x154
[<805897b0>] start_kernel+0x220/0x36c
Kernel panic - not syncing: Attempted to kill the idle task!
This patch fixes the problem
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7118/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The skb->pkt_type field is defined as follows:
u8 pkt_type:3,
fclone:2,
ipvs_property:1,
peeked:1,
nf_trace:1
resulting to the following layout in big-endian systems
[pkt_type][fclone][ipvs_propery][peeked][nf_trace]
^ ^
| |
LSB MSB
As a result, the existing code did not work because it was trying to
match pkt_type == 7 whereas in reality it is 7<<5 on big-endian
systems.
This has been fixed in the interpreter in
0dcceabb0c
"net: filter: fix SKF_AD_PKTTYPE extension on big-endian"
The fix is to look for 7<<5 on big-endian systems for the pkt_type
field, and shift by 5 so the packet type will be at the lower 3 bits
of the A register.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: netdev@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7132/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips: allmodconfig fails in 3.16-rc1 with lots of undefined symbols.
arch/mips/net/bpf_jit.c: In function 'is_load_to_a':
arch/mips/net/bpf_jit.c:559:7: error: 'BPF_S_LD_W_LEN' undeclared (first use in this function)
arch/mips/net/bpf_jit.c:559:7: note: each undeclared identifier is reported only once for each function it appears in
arch/mips/net/bpf_jit.c:560:7: error: 'BPF_S_LD_W_ABS' undeclared (first use in this function)
[...]
The reason behind this is that 3480593131 ("net: filter: get rid of
BPF_S_* enum") was routed via net-next tree, that takes all BPF-related
changes, at a time where MIPS BPF JIT was not part of net-next, while
c6610de353 ("MIPS: net: Add BPF JIT") was routed via mips arch tree
and went into mainline within the same merge window. Thus, fix it up by
converting BPF_S_* in a similar fashion as in 3480593131 for MIPS.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Cc: Linux MIPS Mailing List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7099/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit eec43a224c "MIPS: Save/restore MSA context around
signals" and the MSA parts of ca750649e0 "MIPS: kernel: signal:
Prevent save/restore FPU context in user memory" (the restore path of
which appears incorrect anyway...).
The reverted patch took care not to break compatibility with userland
users of struct sigcontext, but inadvertantly changed the offset of the
uc_sigmask field of struct ucontext. Thus Linux v3.15 breaks the
userland ABI. The MSA context will need to be saved via some other
opt-in mechanism, but for now revert the change to reduce the fallout.
This will have minimal impact upon use of MSA since the only supported
CPU which includes it (the P5600) is 32-bit and therefore requires that
the experimental CONFIG_MIPS_O32_FP64_SUPPORT Kconfig option be selected
before the kernel will set FR=1 for a task, a requirement for MSA use.
Thus the users of MSA are limited to known small groups of people & this
patch won't be breaking any previously working MSA-using userland
outside of experimental settings.
[ralf@linux-mips.org: Fixed rejects.]
Cc: stable@vger.kernel.org
Reported-by: Joseph S. Myers <joseph@codesourcery.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7107/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The fix in the preceeding commit did do exactly the same thing in two
places showing some code cleanup was due.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
icaches are not snooped hence not cohrent in SMP setups which means
kernel has to do cross core calls to ensure the same.
The leaf routine __ic_line_inv_vaddr() now does cross core calls.
__sync_icache_dcache() is affected due to this:
* local dcache line flushed ahead of remote icache inv requests
* can't disable interrupts anymore, since
__ic_line_inv_vaddr()->on_each_cpu() can deadlock.
| WARNING: CPU: 0 PID: 1 at kernel/smp.c:374
| smp_call_function_many+0x25a/0x2c4()
|
| init_kprobes+0x90/0xc8
| register_kprobe+0x1d6/0x510
| __sync_icache_dcache+0x28/0x80
|
| DISABLE IRQ
|
| __ic_line_inv_vaddr
| on_each_cpu
| smp_call_function_many+0x25a/0x2c4 --> WARN
| __ic_line_inv_vaddr_local
| __dc_line_op
* TODO: Needs to use mask of relevant CPUs to avoid broadcasting
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
