Pull drm fixes from Dave Airlie:
"Back from LCA2020, fixes wasn't too busy last week, seems to have
quieten down appropriately, some amdgpu, i915, then a core mst fix and
one fix for virtio-gpu and one for rockchip:
core mst:
- serialize down messages and clear timeslots are on unplug
amdgpu:
- Update golden settings for renoir
- eDP fix
i915:
- uAPI fix: Remove dash and colon from PMU names to comply with
tools/perf
- Fix for include file that was indirectly included
- Two fixes to make sure VMA are marked active for error capture
virtio:
- maintain obj reservation lock when submitting cmds
rockchip:
- increase link rate var size to accommodate rates"
* tag 'drm-fixes-2020-01-19' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Reorder detect_edp_sink_caps before link settings read.
drm/amdgpu: update goldensetting for renoir
drm/dp_mst: Have DP_Tx send one msg at a time
drm/dp_mst: clear time slots for ports invalid
drm/i915/pmu: Do not use colons or dashes in PMU names
drm/rockchip: fix integer type used for storing dp data rate
drm/i915/gt: Mark ring->vma as active while pinned
drm/i915/gt: Mark context->state vma as active while pinned
drm/i915/gt: Skip trying to unbind in restore_ggtt_mappings
drm/i915: Add missing include file <linux/math64.h>
drm/virtio: add missing virtio_gpu_array_lock_resv call
[Why]
Noticed this while testing MST with the 4 ports MST hub from
StarTech.com. Sometimes can't light up monitors normally and get the
error message as 'sideband msg build failed'.
Look into aux transactions, found out that source sometimes will send
out another down request before receiving the down reply of the
previous down request. On the other hand, in drm_dp_get_one_sb_msg(),
current code doesn't handle the interleaved replies case. Hence, source
can't build up message completely and can't light up monitors.
[How]
For good compatibility, enforce source to send out one down request at a
time. Add a flag, is_waiting_for_dwn_reply, to determine if the source
can send out a down request immediately or not.
- Check the flag before calling process_single_down_tx_qlock to send out
a msg
- Set the flag when successfully send out a down request
- Clear the flag when successfully build up a down reply
- Clear the flag when find erros during sending out a down request
- Clear the flag when find errors during building up a down reply
- Clear the flag when timeout occurs during waiting for a down reply
- Use drm_dp_mst_kick_tx() to try to send another down request in queue
at the end of drm_dp_mst_wait_tx_reply() (attempt to send out messages
in queue when errors occur)
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200113093649.11755-1-Wayne.Lin@amd.com
[Why]
When change the connection status in a MST topology, mst device
which detect the event will send out CONNECTION_STATUS_NOTIFY messgae.
e.g. src-mst-mst-sst => src-mst (unplug) mst-sst
Currently, under the above case of unplugging device, ports which have
been allocated payloads and are no longer in the topology still occupy
time slots and recorded in proposed_vcpi[] of topology manager.
If we don't clean up the proposed_vcpi[], when code flow goes to try to
update payload table by calling drm_dp_update_payload_part1(), we will
fail at checking port validation due to there are ports with proposed
time slots but no longer in the mst topology. As the result of that, we
will also stop updating the DPCD payload table of down stream port.
[How]
While handling the CONNECTION_STATUS_NOTIFY message, add a detection to
see if the event indicates that a device is unplugged to an output port.
If the detection is true, then iterrate over all proposed_vcpi[] to
see whether a port of the proposed_vcpi[] is still in the topology or
not. If the port is invalid, set its num_slots to 0.
Thereafter, when try to update payload table by calling
drm_dp_update_payload_part1(), we can successfully update the DPCD
payload table of down stream port and clear the proposed_vcpi[] to NULL.
Changes since v1:(https://patchwork.kernel.org/patch/11275801/)
* Invert the conditional to reduce the indenting
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
[removed cc for stable - there's too many patches this depends on for
this to backport cleanly]
Link: https://patchwork.freedesktop.org/patch/msgid/20200106102158.28261-1-Wayne.Lin@amd.com
Merge Intel Gen9 graphics fix from Akeem Abodunrin:
"Insufficient control flow in certain data structures for some Intel
Processors with Intel Processor Graphics may allow an unauthenticated
user to potentially enable information disclosure via local access
This provides mitigation for Gen9 hardware. Note that Gen8 is not
impacted due to a previously implemented workaround.
The mitigation involves using an existing hardware feature to forcibly
clear down all EU state at each context switch"
* tag 'Intel-CVE-2019-14615' of emailed bundle from Akeem G Abodunrin <akeem.g.abodunrin@intel.com>:
drm/i915/gen9: Clear residual context state on context switch
Intel ID: PSIRT-TA-201910-001
CVEID: CVE-2019-14615
Intel GPU Hardware prior to Gen11 does not clear EU state
during a context switch. This can result in information
leakage between contexts.
For Gen8 and Gen9, hardware provides a mechanism for
fast cleardown of the EU state, by issuing a PIPE_CONTROL
with bit 27 set. We can use this in a context batch buffer
to explicitly cleardown the state on every context switch.
As this workaround is already in place for gen8, we can borrow
the code verbatim for Gen9.
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Cc: Kumar Valsan Prathap <prathap.kumar.valsan@intel.com>
Cc: Chris Wilson <chris.p.wilson@intel.com>
Cc: Balestrieri Francesco <francesco.balestrieri@intel.com>
Cc: Bloomfield Jon <jon.bloomfield@intel.com>
Cc: Dutt Sudeep <sudeep.dutt@intel.com>
For high-res (8K) or HFR (4K120) displays, using uncompressed pixel
formats like YCbCr444 would exceed the bandwidth of HDMI 2.0, so the
"interesting" modes would be disabled, leaving only low-res or low
framerate modes.
This change lowers the pixel encoding to 4:2:2 or 4:2:0 if the max TMDS
clock is exceeded. Verified that 8K30 and 4K120 are now available and
working with a Samsung Q900R over an HDMI 2.0b link from a Radeon 5700.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Thomas Anderson <thomasanderson@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When userspace requests a video mode parameter value that is not
supported, frame buffer device drivers should round it up to a supported
value, if possible, instead of just rejecting it. This allows
applications to quickly scan for supported video modes.
Currently this rule is not followed for the number of bits per pixel,
causing e.g. "fbset -depth N" to fail, if N is smaller than the current
number of bits per pixel.
Fix this by returning an error only if bits per pixel is too large, and
setting it to the current value otherwise.
See also Documentation/fb/framebuffer.rst, Section 2 (Programmer's View
of /dev/fb*").
Fixes: 865afb1194 ("drm/fb-helper: reject any changes to the fbdev")
Cc: stable@vger.kernel.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20191230132734.4538-1-geert+renesas@glider.be
In commit 0b8e7bbde5 ("drm/sun4i: tcon: Set min division of TCON0_DCLK
to 1.") it was assumed that all TCON variants support a minimum divider
of 1 if only DCLK was used.
However, the oldest generation of hardware only supports minimum divider
of 4 if only DCLK is used. If a divider of 1 was used on this old
hardware, some scrolling artifact would appear. A divider of 2 seemed
OK, but a divider of 3 had artifacts as well.
Set the minimum divider when outputing to parallel RGB based on the
hardware model, with a minimum of 4 for the oldest (A10/A10s/A13/A20)
hardware, and a minimum of 1 for the rest. A value is not set for the
TCON variants lacking channel 0.
This fixes the scrolling artifacts seen on my A13 tablet.
Fixes: 0b8e7bbde5 ("drm/sun4i: tcon: Set min division of TCON0_DCLK to 1.")
Cc: <stable@vger.kernel.org> # 5.4.x
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20200107070113.28951-1-wens@kernel.org
Revert changes done in commit f6ec948309 ("drm/i915: extend audio
CDCLK>=2*BCLK constraint to more platforms"). Audio drivers
communicate with i915 over HDA bus multiple times during system
boot-up and each of these transactions result in matching
get_power/put_power calls to i915, and depending on the platform,
a modeset change causing visible flicker.
GLK is the only platform with minimum CDCLK significantly lower
than BCLK, and thus for GLK setting a higher CDCLK is mandatory.
For other platforms, minimum CDCLK is close but below 2*BCLK
(e.g. on ICL, CDCLK=176.4kHz with BCLK=96kHz). Spec-wise the constraint
should be set, but in practise no communication errors have been
reported and the downside if set is the flicker observed at boot-time.
Revert to old behaviour until better mechanism to manage
probe-time clocks is available.
The full CDCLK>=2*BCLK constraint is still enforced at pipe
enable time in intel_crtc_compute_min_cdclk().
Bugzilla: https://gitlab.freedesktop.org/drm/intel/issues/913
Fixes: f6ec948309 ("drm/i915: extend audio CDCLK>=2*BCLK constraint to more platforms")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191231140007.31728-1-kai.vehmanen@linux.intel.com
(cherry picked from commit 1ee48a61aa)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[Why]
According to DP spec, it should shift left 4 digits for NO_STOP_BIT
in REMOTE_I2C_READ message. Not 5 digits.
In current code, NO_STOP_BIT is always set to zero which means I2C
master is always generating a I2C stop at the end of each I2C write
transaction while handling REMOTE_I2C_READ sideband message. This issue
might have the generated I2C signal not meeting the requirement. Take
random read in I2C for instance, I2C master should generate a repeat
start to start to read data after writing the read address. This issue
will cause the I2C master to generate a stop-start rather than a
re-start which is not expected in I2C random read.
[How]
Correct the shifting value of NO_STOP_BIT for DP_REMOTE_I2C_READ case in
drm_dp_encode_sideband_req().
Changes since v1:(https://patchwork.kernel.org/patch/11312667/)
* Add more descriptions in commit and cc to stable
Fixes: ad7f8a1f9c ("drm/helper: add Displayport multi-stream helper (v0.6)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200103055001.10287-1-Wayne.Lin@amd.com
Per confirmation with RLC firmware team, the RLC should
be unhalted after all RLC related firmwares uploaded.
However, in fact the RLC is unhalted immediately after
RLCG firmware uploaded. And that may causes unexpected
PSP hang on loading the succeeding RLC save restore
list related firmwares.
So, we correct the firmware loading sequence to load
RLC save restore list related firmwares before RLCG
ucode. That will help to get around this issue.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When smu version is larger than 0x41e2b, it will load
raven_kicker_rlc.bin.To enable gfxoff for raven_kicker_rlc.bin,it
needs to avoid adev->pm.pp_feature &= ~PP_GFXOFF_MASK when it loads
raven_kicker_rlc.bin.
Signed-off-by: changzhu <Changfeng.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Avoid rc6 counter going backward in close to 0% RC6 scenarios like:
15.005477996 114,246,613 ns i915/rc6-residency/
16.005876662 667,657 ns i915/rc6-residency/
17.006131417 7,286 ns i915/rc6-residency/
18.006615031 18,446,744,073,708,914,688 ns i915/rc6-residency/
19.007158361 18,446,744,073,709,447,168 ns i915/rc6-residency/
20.007806498 0 ns i915/rc6-residency/
21.008227495 1,440,403 ns i915/rc6-residency/
There are two aspects to this fix.
First is not assuming rc6 value zero means GT is asleep since that can
also mean GPU is fully busy and we do not want to enter the estimation
path in that case.
Second is ensuring monotonicity on the estimation path itself. I suspect
what is happening is with extremely rapid park/unpark cycles we get no
updates on the real rc6 and therefore have to careful not to
unconditionally trust use last known real rc6 when creating a new
estimation.
v2:
* Simplify logic by not tracking the estimate but last reported value.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Fixes: 16ffe73c18 ("drm/i915/pmu: Use GT parked for estimating RC6 while asleep")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> # v1
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191217142057.1000-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit df6a420535)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
- Fix to drop an unused and harmful display W/A
- Fix to define EHL power wells independent of ICL
- Fix for priority inversion on bonded requests
- Fix in mmio offset calculation of DSB instance
- Fix memory leak from get_task_pid when banning clients
- Fixes to avoid dereference of uninitialized ops in dma_fence tracing
and keep reference to execbuf object until submitted.
- Includes gvt-fixes-2019-12-18
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191219124635.GA16068@jlahtine-desk.ger.corp.intel.com
The driver forgets to call component_del in remove to match component_add
in probe.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Inki Dae <inki.dae@samsung.net>
