It is no longer present in newer cores. Unfortunately Freescale decided
to put the bit which decides between automotive clock path and consumer
clock path in the automotive clock path direction. With current code we
cannot detect the core revision, so just remove automotive path completely.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This iomux is called iomux-v3 in the tree because it is the third known
incarnation of MXC iomuxers. It is not only found on the MX35 but also
on the MX51 and probably others.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Merge reason: this topic is ready for upstream now. It passed
Oleg's review and Andrew had no further mm/*
objections/observations either.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add support for S3C6400 SDHCI channels 0 and 1, making
the GPIO code common to both S3C6400 and S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add detection support for the S3C6400 SoC which has it's
id register in a different place to the S3C6410.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add power management support to the VIC by registering
each VIC as a system device to get suspend/resume
events going.
Since the VIC registeration is done early, we need to
record the VICs in a static array which is used to add
the system devices later once the initcalls are run. This
means there is now a configuration value for the number
of VICs in the system.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the GPIO suspend/resume support inline with the gpiolib support
so that it will work with both the S3C24XX and S3C64XX series.
The s3c_gpio_chip is extended to have a pm callback and a save block
to keep the state of the GPIO over suspend, and the code from the
s3c24xx implementation is added to a new common file.
The suspend process now uses the list of registered chips to go through
saving and restoring each one as appropriate, using the pm callback to
select the appropriate routine depending on the type of control register
present.
This change also means that any additional GPIO added should not require
changes to the PM.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for saving the state of the IRQ registers over suspend.
This requires moving the S3C64XX UART registers into <plat/regs-serial.h>
and adding irq-pm.c which saves the state of all the IRQ registers.
The irq-pm.c saves all the IRQ registers, including the IRQ_EINT and
IRQ_EINT_GROUP registers as it was easier than adding three different
files. Also ensuring that all the registers are restored to the same
state as before suspend is considered to be the best thing to do.
Note, we do not suspend the VIC here, this is done by the VIC driver
itself.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add an s3c64xx_sysclass and device for items that currently
want to bind to any s3c64xx processor. The first user of this
will be parts of the s3c64xx suspend support which need to
save device state over suspend/resume.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the initial support for the S3C64XX based systems to use
suspend-to-RAM to sleep.
Includes basic debugging for use with the SMDK6410 usign the
LEDs on the baseboard.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add a simple debug message on saving the UART state and add a per-arch
pre-restore function to be used by the s3c64xx restore code to ensure
the UARTs control registers do not go through any illegal state changes.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The USB host base address is available on both the S3C24XX and S3C64XX
ranges.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add USB OHCI host capability to the SMDK6410 for either USB OtG or
a single/double USB host port.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add common definition for USB OHCI platform device, add a Kconfig
to selectively compile it and add update all the users.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Merge reason: tracing/core was on a .30-rc1 base and was missing out on
on a handful of tracing fixes present in .30-rc5-almost.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh64 is still using this, so re-enable it temporarily while SH-5 gets
converted to use the generic code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When we set a filter for an event, such as:
echo "name == my_lock_name" > \
/debug/tracing/events/lockdep/lock_acquired/filter
then the following order of token type is parsed:
- space
- operator
- parentheses
- operand
Because the operators and parentheses have a higher precedence
than the operand characters, which is normal, then we can't
use any string containing such special characters:
()=<>!&|
To get this support and also avoid ambiguous intepretation from
the parser or the human, we can do it using double quotes so that
we keep the usual languages habits.
Then after this patch you can still declare string condition like
before:
echo name == myname
But if you want to compare against a string containing an operator
character, you can use double quotes:
echo 'name == "&myname"'
Don't forget to include the whole expression into single quotes or
the double ones will be eaten by echo.
[ Impact: support strings with special characters for tracing filters ]
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Zhaolei <zhaolei@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Currently the filtering infrastructure supports well the
numeric types and fixed sized array types.
But the recently added __string() field uses a specific
indirect offset mechanism which requires a specific
predicate. Until now it wasn't supported.
This patch adds this support and implies very few changes,
only a new predicate is needed, the management of this specific
field can be done through the usual string helpers in the
filtering infrastructure.
[ Impact: support all kinds of strings in the tracing filters ]
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Zhaolei <zhaolei@cn.fujitsu.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Presently shm_align_mask is only looked at for the bottom up case, but we
still want this for proper colouring constraints in the topdown case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When a thread is oom killed and fails to exit, it's helpful to know which
threads have access to memory reserves if the machine livelocks. This is
done by testing for the TIF_MEMDIE thread info flag and should be
displayed alongside stack traces to identify tasks that have access to
such reserves but are still stuck allocating pages, for instance.
It would probably be helpful in other cases as well, so all thread info
flags are emitted when showing a task.
( v2: fix warning reported by Stephen Rothwell )
[ Impact: extend debug printout info ]
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <alpine.DEB.2.00.0905040136390.15831@chino.kir.corp.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
- remove unused define
- make the lock variable definition stand out some more
- convert KERN_* to pr_info() / pr_warning()
[ Impact: cleanup ]
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There still seems to be some stack corruption to sort out here, so flag
this as BROKEN until this issue is sorted out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code has apparently used "0" and not VM86_SIGNAL since Linux
1.1.9, when Linus added VM86_SIGNAL to vm86.h. This patch changes the
code to use the symbolic name.
The magic 0 tripped me up in trying to extend the vm86(2) manpage to
actually explain vm86()'s interface -- my greps for VM86_SIGNAL came up
fruitless.
[ Impact: cleanup; no object code change ]
Signed-off-by: Samuel Bronson <naesten@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
With the current event directory, you can only enable individual events.
The file debugfs/tracing/set_event is used to be able to enable or
disable several events at once. But that can still be awkward.
This patch adds hierarchical enabling of events. That is, each directory
in debugfs/tracing/events has an "enable" file. This file can enable
or disable all events within the directory and below.
# echo 1 > /debugfs/tracing/events/enable
will enable all events.
# echo 1 > /debugfs/tracing/events/sched/enable
will enable all events in the sched subsystem.
# echo 1 > /debugfs/tracing/events/enable
# echo 0 > /debugfs/tracing/events/irq/enable
will enable all events, but then disable just the irq subsystem events.
When reading one of these enable files, there are four results:
0 - all events this file affects are disabled
1 - all events this file affects are enabled
X - there is a mixture of events enabled and disabled
? - this file does not affect any event
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Li Zefan found that there's a race using the event ids of events and
modules. When a module is loaded, an event id is incremented. We only
have 16 bits for event ids (65536) and there is a possible (but highly
unlikely) race that we could load and unload a module that registers
events so many times that the event id counter overflows.
When it overflows, it then restarts and goes looking for available
ids. An id is available if it was added by a module and released.
The race is if you have one module add an id, and then is removed.
Another module loaded can use that same event id. But if the old module
still had events in the ring buffer, the new module's call back would
get bogus data. At best (and most likely) the output would just be
garbage. But if the module for some reason used pointers (not recommended)
then this could potentially crash.
The safest thing to do is just reset the ring buffer if a module that
registered events is removed.
[ Impact: prevent unpredictable results of event id overflows ]
Reported-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <49FEAFD0.30106@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When creating trace events for ftrace, the header file with the TRACE_EVENT
macros must also have a macro called TRACE_SYSTEM. This macro describes
the name of the system the TRACE_EVENTS are defined for. It also doubles
as a way for the define_trace.h file to include the file that included
it.
For example:
in irq.h
#define TRACE_SYSTEM irq
[...]
#include <trace/define_trace.h>
The define_trace will use TRACE_SYSTEM to include irq.h. But if the name
of the trace system does not match the name of the trace header file,
one can override it with:
Which will change define_trace.h to inclued foo_trace.h instead of foo.h
The sample comments this, but people that use the sample code will more
likely use the code and not read the comments. This patch changes the
sample code to use the TRACE_INCLUDE_FILE to better show developers how to
use it.
[ Impact: make sample less confusing to developers ]
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
