It appears that we wrongly calculate dev_base for type1 config cycles.
The thing is: we shouldn't subtract hose->first_busno because PCI core
sets PCI primary, secondary and subordinate bus numbers, and PCIe
controller actually takes the registers into account. So we should use
just bus->number.
Also, according to MPC8315 reference manual, primary bus number should
always remain 0. We have PPC_INDIRECT_TYPE_SURPRESS_PRIMARY_BUS quirk
in indirect_pci.c, but since 83xx is somewhat special, it doesn't use
indirect_pci.c routines, so we have to implement the quirk specifically
for 83xx PCIe controllers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'bkl-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mn10300: Remove the BKL from sys_execve
m68knommu: Remove the BKL from sys_execve
m68k: Remove the BKL from sys_execve
h83000: Remove BKL from sys_execve
frv: Remove the BKL from sys_execve
blackfin: Remove the BKL from sys_execve
um: Remove BKL from mmapper
um: Remove BKL from random
s390: Remove BKL from prng
A previous patch was introducing a SPARSEMEM dependency on
!HIGH_PHYS_OFFSET but it should actually be !REALVIEW_HIGH_PHYS_OFFSET.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since this IRQ descriptor doesn't have an action registered, it is
allowed for probing via probe_irq_on/off() and it will be disabled by
the latter function. This patch sets the IRQ_NOPROBE status bit for the
local timer descriptor.
Signed-off-by: Varun Swara <Varun.Swara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The core files of DSS2. DSS2 commits are split a bit artificially to
make the individual commits smaller, and DSS2 doesn't compile properly
without the rest of the core commits. This shouldn't be a problem, as no
configuration uses DSS2 yet.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
VRFB rotation engine is a block in OMAP2/3 that offers 12 independent
contexts that can be used for framebuffer rotation.
Each context has a backend area of real memory, where it stores the
pixels in undisclosed format. This memory is offered to users via 4
virtual memory areas, which see the same memory area in different
rotation angles (0, 90, 180 and 270 degrees).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a Video RAM manager for OMAP 2 and 3 platforms. VRAM manager is used
to allocate large continuous blocks of SDRAM or SRAM. The features VRAM
manager has that are missing from dma_alloc_* functions are:
- Support for OMAP2's SRAM
- Allocate without ioremapping
- Allocate at defined physical addresses
- Allows larger VRAM area and larger allocations
The upcoming DSS2 uses VRAM manager.
VRAM area size can be defined in kernel config, board file or with
kernel boot parameters. Board file definition overrides kernel config,
and boot parameter overrides kernel config and board file.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The upcoming new display subsystem driver is divided to two devices,
omapdss and omapfb, of which omapdss handles the actual hardware.
This patch adds a dummy omapdss platform device for the current omapfb
driver, which is then used to get the clocks. This will make it possible
for the current and the new display drivers to co-exist.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch allows an earlyprintk console if CONFIG_DEBUG_LL is enabled,
using the printch asm function.
The patch is based on the original work by Sascha Hauer.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Commit 4f70f7a91b
(sparc64: Implement IRQ stacks.) has two bugs.
First, the softirq range check forgets to subtract STACK_BIAS
before comparing with %sp. Next, on failure the wrong label
is jumped to, resulting in a bogus stack being loaded.
Reported-by: Igor Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are trying to see if a range property entry applies
to a given address, we are overly strict about the type.
We should only allow I/O ranges for I/O addresses, and only allow
CONFIG space ranges for CONFIG space address.
However for MEM ranges, they come in 32-bit and 64-bit flavors.
And a lack of an exact match is OK if the range is 32-bit and
the address is 64-bit. We can assign a 64-bit address properly
into a 32-bit parent range just fine.
So allow it.
Reported-by: Patrick Finnegan <pat@computer-refuge.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when ptrace needs to modify a breakpoint, like disabling
it, changing its address, type or len, it calls
modify_user_hw_breakpoint(). This latter will perform the heavy and
racy task of unregistering the old breakpoint and registering a new
one.
This is racy as someone else might steal the reserved breakpoint
slot under us, which is undesired as the breakpoint is only
supposed to be modified, sometimes in the middle of a debugging
workflow. We don't want our slot to be stolen in the middle.
So instead of unregistering/registering the breakpoint, just
disable it while we modify its breakpoint fields and re-enable it
after if necessary.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
LKML-Reference: <1260347148-5519-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On SUN3, m68k defines macro VMALLOC_END as unsigned long variable
vmalloc_end which is adjusted from mmu_emu_init(). This becomes
problematic if a local variables vmalloc_end is defined in some
function (not very unlikely) and VMALLOC_END is used in the function -
the function thinks its referencing the global VMALLOC_END value but
would be referencing its own local vmalloc_end variable.
Rename the global variable to m68k_vmlloc_end which is much less
likely to be used as local variable name.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
- Use #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
- Remove "microcode: " prefix from each pr_<level>
- Fix duplicated KERN_ERR prefix
- Coalesce pr_<level> format strings
- Add a space after an exclamation point
No other change in output.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Andreas Herrmann <herrmann.der.user@googlemail.com>
LKML-Reference: <1260340250.27677.191.camel@Joe-Laptop.home>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
e821ea70f3 introduced a bug by copying
some 64-bit originated code as-is to be used by both 32 and 64-bit
but this code contains a 64-bit ony "cmpdi" instruction.
This changes it to cmpwi, which is fine since VRSAVE can only contains
a 32-bit value anyway.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@kernel.org>
At the moment when we EOI an interrupt we set the CPPR back to 0xFF
regardless of its previous value. This could lead to problems if we
take an interrupt with a priority of 5, but before EOIing it we get
an IPI which has a priority of 4. The problem is that at the moment
when we EOI the IPI we will set the CPPR to 0xFF, but it should
really be set back to 5 (the previous priority).
To keep track of the previous CPPR values we create the xics_cppr
structure that has an array for CPPR values and an index pointing
to the current priority. This can easily grow if new priorities get
added in the future.
This will also be useful because the partition adjunct option of
upcoming machines will update the H_XIRR hcall to accept the CPPR
as a parameter.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The recent patch to add cpu offline/online as part of the DLPAR
process for pseries causes a build break if CONFIG_SMP is not
defined. Original patch here;
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-November/078299.html
This corrects the build break by moving the online_node_cpus
and offline_node_cpus under the #ifdef CONFIG_ARCH_CPU_PROBE_RELEASE
portions of dlpar.c.
This patch also slightly modifies the online_node_cpus and offline_node_cpus
routines to prepend dlpar_ to the them and make them static. These two
routine are only used in the dlpar add/remove of cpus and these changes
should help clarify that.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Writing a driver using SCLPC on the MPC5200B I detected, that the
intspec arrays to map irqs to Linux virq cannot be const, because the
mapping and xlate functions only take non const pointers. All those
functions do not modify the intspec, so a const pointer could be used.
Signed-off-by: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There is no need to do set the DIRTY bit directly in DTLB Error.
Trap to do_page_fault() and let the generic MM code do the work.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that 8xx can fixup dcbX instructions, start using them
where possible like every other PowerPc arch do.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
8xx has not had WRITETHRU due to lack of bits in the pte.
After the recent rewrite of the 8xx TLB code, there are
two bits left. Use one of them to WRITETHRU.
Perhaps use the last SW bit to PAGE_SPECIAL or PAGE_FILE?
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
only DTLB Miss did set this bit, DTLB Error needs too otherwise
the setting is lost when the page becomes dirty.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is an assembler version to fixup DAR not being set
by dcbX, icbi instructions. There are two versions, one
uses selfmodifing code, the other uses a
jump table but is much bigger(default).
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
dcbz, dcbf, dcbi, dcbst and icbi do not set DAR when they
cause a DTLB Error. Dectect this by tagging DAR with 0x00f0
at every exception exit that modifies DAR.
Test for DAR=0x00f0 in DataTLBError and bail
to handle_page_fault().
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update the TLB asm to make proper use of _PAGE_DIRY and _PAGE_ACCESSED.
Get rid of _PAGE_HWWRITE too.
Pros:
- I/D TLB Miss never needs to write to the linux pte.
- _PAGE_ACCESSED is only set on TLB Error fixing accounting
- _PAGE_DIRTY is mapped to 0x100, the changed bit, and is set directly
when a page has been made dirty.
- Proper RO/RW mapping of user space.
- Free up 2 SW TLB bits in the linux pte(add back _PAGE_WRITETHRU ?)
- kernel RO/user NA support.
Cons:
- A few more instructions in the TLB Miss routines.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
8xx sometimes need to load a invalid/non-present TLBs in
it DTLB asm handler.
These must be invalidated separaly as linux mm don't.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the cpu-allocation/deallocation process comprises of two steps:
- Set the indicators and to update the device tree with DLPAR node
information.
- Online/offline the allocated/deallocated CPU.
This is achieved by writing to the sysfs tunables "probe" during allocation
and "release" during deallocation.
At the sametime, the userspace can independently online/offline the CPUs of
the system using the sysfs tunable "online".
It is quite possible that when a userspace tool offlines a CPU
for the purpose of deallocation and is in the process of updating the device
tree, some other userspace tool could bring the CPU back online by writing to
the "online" sysfs tunable thereby causing the deallocate process to fail.
The solution to this is to serialize writes to the "probe/release" sysfs
tunable with the writes to the "online" sysfs tunable.
This patch employs a mutex to provide this serialization, which is a no-op on
all architectures except PPC_PSERIES
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the cpu-allocation/deallocation on pSeries is a
two step process from the Userspace.
- Set the indicators and update the device tree by writing to the sysfs
tunable "probe" during allocation and "release" during deallocation.
- Online / Offline the CPUs of the allocated/would_be_deallocated node by
writing to the sysfs tunable "online".
This patch adds kernel code to online/offline the CPUs soon_after/just_before
they have been allocated/would_be_deallocated. This way, the userspace tool
that performs DLPAR operations would only have to deal with one set of sysfs
tunables namely "probe" and release".
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Remove the CPU from the online map to prevent smp_call_function
from sending messages to a stopped CPU.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the specific routines to probe and release (add and remove)
cpu resource for the powerpc pseries platform and registers these handlers
with the ppc_md callout structure.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Version 3 of this patch is updated with documentation added to
Documentation/ABI. There are no changes to any of the C code from v2
of the patch.
In order to support kernel DLPAR of CPU resources we need to provide an
interface to add (probe) and remove (release) the resource from the system.
This patch Creates new generic probe and release sysfs files to facilitate
cpu probe/release. The probe/release interface provides for allowing each
arch to supply their own routines for implementing the backend of adding
and removing cpus to/from the system.
This also creates the powerpc specific stubs to handle the arch callouts
from writes to the sysfs files.
The creation and use of these files is regulated by the
CONFIG_ARCH_CPU_PROBE_RELEASE option so that only architectures that need the
capability will have the files created.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Dynamic Logical Partitioning capabilities of the powerpc pseries platform
allows for the addition and removal of resources (i.e. CPU's, memory, and PCI
devices) from a partition. The removal of a resource involves
removing the resource's node from the device tree and then returning the
resource to firmware via the rtas set-indicator call. To add a resource, it
is first obtained from firmware via the rtas set-indicator call and then a
new device tree node is created using the ibm,configure-coinnector rtas call
and added to the device tree.
This patch provides the kernel DLPAR infrastructure in a new filed named
dlpar.c. The functionality provided is for acquiring and releasing a resource
from firmware and the parsing of information returned from the
ibm,configure-connector rtas call. Additionally this exports the pSeries
reconfiguration notifier chain so that it can be invoked when device tree
updates are made.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The hotplug mediabay has tendrils deep into drivers/ide code
which makes a libata port reather difficult. In addition it's
ugly and could be done better.
This reworks the interface between the mediabay and the rest
of the world so that:
- Any macio_driver can now have a mediabay_event callback
which will be called when that driver sits on a mediabay and
it's been either plugged or unplugged. The device type is
passed as an argument. We can now move all the IDE cruft
into the IDE driver itself
- A check_media_bay() function can be used to take a peek
at the type of device currently in the bay if any, a cleaner
variant of the previous function with the same name.
- A pair of lock/unlock functions are exposed to allow the
IDE driver to block the hotplug callbacks during the initial
setup and probing of the bay in order to avoid nasty race
conditions.
- The mediabay code no longer needs to spin on the status
register of the IDE interface when it detects an IDE device,
this is done just fine by the IDE code itself
Overall, less code, simpler, and allows for another driver
than our old drivers/ide based one.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Current soc-camera needs SOCAM_DATA_ACTIVE_xxx flags for use.
We can not open old ncm03j camera device without this patch.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a ->start_transfer() callback to the
KFR2R09 lcd handling code. The callback is used to
notify the lcd controller that a new frame of data
is about to be transferred. The callback is only used
in combination with deferred io, but the code has
been tested both with and without deferred io enabled.
Without this patch the display data on the KFR2R09
lcd panel becomes corrupted over time.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the NUMA version of setup_memory()
with UMA code changes and also modifies the last argument
to lmb_alloc_base() to use an address instead of pfn.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the NUMA size calculation for node 0. Do the same
as the UMA version of setup_memory() and use address
instead of pfn when calculating the size.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The macro container_of from kernel.h performs the same
pointer arithmetic operation.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression mptr;
expression member;
@@
- (void *)((char *)mptr - offsetof(T, member))
+ container_of(mptr, T, member)
// </smpl>
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
