The system will die if the kernel is booted with "reservetop"
parameter, in present code, parse "reservetop" parameter after
early_ioremap_init(), and some function still use
early_ioremap() after it.
The problem is, "reservetop" parameter can modify
'FIXADDR_TOP', then the virtual address got by early_ioremap()
is base on old 'FIXADDR_TOP', but the page mapping is base on
new 'FIXADDR_TOP', it will occur page fault, and the IDT is not
prepare yet, so, the system is dead.
So, put parse_early_param() in the front of
early_ioremap_init() in this patch.
Signed-off-by: Xiao Guangrong <xiaoguangrong@cn.fujitsu.com>
Cc: yinghai@kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <4A8D402F.4080805@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allow a DWARF register to have an undefined value. When applied to the
DWARF return address register this lets lets us label a function as
having no direct caller, e.g. kernel_thread_helper().
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The 'end' member of struct dwarf_fde denotes one byte past the end of
the CFA instruction stream for an FDE. The value of 'end' was being
calcualted incorrectly, it was being set too high. This resulted in
dwarf_cfa_execute_insns() interpreting data past the end of valid
instructions, thus causing all sorts of weird crashes.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
When CONFIG_DWARF_UNWINDER is enabled setup r14 in handle_interrupt, so
that we can figure out what function was running when we were
interrupted.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
We can't assume that if we execute the unwinder code and the unwinder
was already running that it has faulted. Clearly two kernel threads can
invoke the unwinder at the same time and may be running simultaneously.
The previous approach used BUG() and BUG_ON() in the unwinder code to
detect whether the unwinder was incapable of unwinding the stack, and
that the next available unwinder should be used instead. A better
approach is to explicitly invoke a trap handler to switch unwinders when
the current unwinder cannot continue.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
The handling of DW_CFA_val_offset ops was incorrectly using the
DWARF_REG_OFFSET flag but the register's value cannot be calculated
using the DWARF_REG_OFFSET method. Create a new flag to indicate that a
different method must be used to calculate the register's value even
though there is no implementation for DWARF_VAL_OFFSET yet; it's mainly
just a place holder.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Plug a memory leak in dwarf_unwinder_dump() where we didn't free the
memory that we had previously allocated for the DWARF frames and DWARF
registers.
Now is also a opportune time to implement our own mempool and kmem
cache. It's a good idea to have a certain number of frame and register
objects in reserve at all times, so that we are guaranteed to have our
allocation satisfied even when memory is scarce. Since we have pools to
allocate from we can implement the registers for each frame as a linked
list as opposed to a sparsely populated array. Whilst it's true that the
lookup time for a linked list is larger than for arrays, there's only
usually a maximum of 8 registers per frame. So the overhead isn't that
much of a concern.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Add core support for the range of S3C24XX Simtec boards with TLV320AIC23
CODECs on them. Since there are also boards with similar IIS routing the
AMP and the configuration code is placed in a core file for re-use with
other CODEC bindings.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
on_each_cpu() takes care of IRQ and preempt handling, the localized
handling in each of the called functions can be killed off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of rework for making the cache flushers SMP-aware. The
function pointer-based flushers are renamed to local variants with the
exported interface being commonly implemented and wrapping as necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All CPU-specific overloads are done at runtime now, so this common header
can go away and simply be folded back in to asm/ version.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the kfr2r09 defconfig with support for LCDC and USB gadget.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add romImage defconfig for the kfr2r09 board. This defconfig
should be used to build the kernel based boot loader.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a P1 jump to the the kfr2r09 romimage code. With this
patch applied the initial zImage assembly code will run
with instruction cache enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add instruction cache and TLB invalidation code for the
the kfr2r09 romimage target.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
It adds a new sysfs file, where the user can configure the mcbsp mode to use.
If the mcbsp channel is in use, it does not allow the change.
Than in omap_pcm_open we can call the omap_mcbsp_get_opmode to get the mode,
store it, than use it to implement the different modes.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Do not allow applications to use the full buffer found on
McBSP1,3,4,5. Using the full buffer in threshold mode causes
the McBSP buffer to run dry, which can be observed as channels
are switching (in reality the channels are shifting).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch export through sysfs two properties to configure
maximum threshold for transmission and reception on each
mcbsp instance. Also, it exports two helper functions to
allow mcbsp users to read this values.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Increasing startup delay value as worst case:
CLKSRG*2 = 8000khz: (1/8000) * 2 * 2 usec
Although, 100us may give enough time for two CLKSRG,
due to some unknown PM related, clock gating etc. reason,
this patch increases it to 500us.
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ASoC has an annoying bug letting either L or R channel to be
played on L channel. In other words, L and R channels can
switch at random. This provides McBSP funtionality that may
be used to fix this feature.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When get_mmu_context() runs out of new ASIDs it flushes the TLB and
wraps around. Despite the fact the ASIDs are tracked per-CPU, a global
TLB flush was being used. Switch this over to a local one, as matches
the intent.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is the only board that presently supports this rtc, so make sure it
is enabled by default to get some build coverage.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As an excellent indicator of how much testing the DSP code gets, a couple
of rather glaring bugs in the DSP save/restore paths were found:
- In the DSP restore case a0 needs to be popped off before a0g,
or the value of a0g is clobbered by the MSB of a0 in the case
of sign extension.
- Beyond that, the save and restore orders were out of sync,
so this fixes that up as well. At the same time, we switch over
to using movs.l for both the save and restore of the general DSP
registers as opposed to using sts.l (which was initially put in
place to work around a bug in ancient binutils versions which
the kernel no longer supports).
Reported-by: Chee Soon Yip <yip.cheesoon@renesas.com>
Cc: Chu Lih Kwek <kwek.chulih@renesas.com>,
Cc: General Lai <general.lai@renesas.com>,
Cc: Robert Cozens <Robert.Cozens@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-tip can't be bothered keeping interfaces stable long enough for anyone
to use them without having their builds broken without notification, so
just ifdef around the problematic symbols until the new interfaces become
available upstream.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
gcc v4.4 currently produces this build warning:
arch/powerpc/boot/mktree.c: In function 'main':
arch/powerpc/boot/mktree.c:104: warning: dereferencing type-punned pointer will break strict-aliasing rules
tmpbuf is only used as an array of unsigned ints, so declare it that way.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently _edata does not include several data sections, this causes
the kernel's report of memory usage at boot to not match reality, and
also prevents kmemleak from working - because it scan between _sdata
and _edata for pointers to allocated memory.
This mirrors a similar change made recently to the x86 linker script.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make it possible to enable GCOV code coverage measurement on powerpc.
Lightly tested on 64-bit, seems to work as expected.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
