Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These patches extend struct platform device data for a bunch of
SuperH Mobile processors and embedded boards. The patches simply
add hardware block ids to on-chip platform devices. Platform
devices off chip (such as external ethernet controllers or flash
chips) are left out which gives them a special case hardware block
id of zero.
Upcoming Runtime PM code will make use of the hardware block id
to group devices together. The hardware block id can also be used
to extend the SuperH Mobile clock framework implementation.
This series of patches depend on the following:
"Driver Core: Add platform device arch data V3".
This patch adds a hwblk_id member to struct pdev_archdata. This member
should be used to point out on-chip hardware block id.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was no big meaning in the support of SVGA,
but 720p support is necessary for ms7724se board.
So, this patch support 720p instead of SVGA.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes the unused MSTPCRn register definitions
from the SuperH Mobile code for sh7722, sh7723 and sh7724.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds early printk support for SH770x (tested on SH7709 based hp6xx).
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
From Gabe Black in bugzilla 13888:
native_save_fl is implemented as follows:
11static inline unsigned long native_save_fl(void)
12{
13 unsigned long flags;
14
15 asm volatile("# __raw_save_flags\n\t"
16 "pushf ; pop %0"
17 : "=g" (flags)
18 : /* no input */
19 : "memory");
20
21 return flags;
22}
If gcc chooses to put flags on the stack, for instance because this is
inlined into a larger function with more register pressure, the offset
of the flags variable from the stack pointer will change when the
pushf is performed. gcc doesn't attempt to understand that fact, and
address used for pop will still be the same. It will write to
somewhere near flags on the stack but not actually into it and
overwrite some other value.
I saw this happen in the ide_device_add_all function when running in a
simulator I work on. I'm assuming that some quirk of how the simulated
hardware is set up caused the code path this is on to be executed when
it normally wouldn't.
A simple fix might be to change "=g" to "=r".
Reported-by: Gabe Black <spamforgabe@umich.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stable Team <stable@kernel.org>
Make rdmsr_on_cpus/wrmsr_on_cpus execute on the current CPU only if it
is in the supplied bitmask.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Older versions of binutils did not accept the naked "ASSERT" syntax;
it is considered an expression whose value needs to be assigned to
something.
Reported-tested-and-fixed-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The latest Apple MacBook (MacBook5,2) doesn't reboot successfully
under Linux; neither the EFI reboot method nor the default method
using the keyboard controller works (the system just hangs and doesn't
reset). However, the method using the "PCI reset register" at 0xcf9
does work.
This adds a quirk to detect this machine via DMI and force the
reboot_type to BOOT_CF9. With this it reboots successfully without
requiring a command-line option. Note that the EFI code forces
reboot_type to BOOT_EFI when the machine is booted via EFI, but this
overrides that since the core_initcall runs after the EFI
initialization code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
LKML-Reference: <19062.56420.501516.316181@cargo.ozlabs.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There were three different errors resulting in a "dangerous relocation"
message. Add the relocation type to the messgages to make them more
useful.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In mm/slab.c the function do_ccupdate_local requires that interrupts be
disabled. If they are not, we panic with CONFIG_DEBUG_SLAB.
So we disable interrupts while processing IPIs. Also these are not shared
irqs, so get rid of the IRQF_SHARED flag.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check whether index is within bounds before testing the element.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d
but is perhaps more readable.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@haskernel@
@@
#include <linux/kernel.h>
@depends on haskernel@
expression x,__divisor;
@@
- (((x) + ((__divisor) / 2)) / (__divisor))
+ DIV_ROUND_CLOSEST(x,__divisor)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following warning at boot time:
WARNING: at drivers/gpio/gpiolib.c:83 0x8021d5e0()
autorequest GPIO-207
Modules linked in:
Call Trace:[<8011e0ec>] 0x8011e0ec
[<80110a28>] 0x80110a28
[<80110a28>] 0x80110a28
[..snip..]
The current code does not request the GPIO and attempts
to set its direction, which is a violation of the GPIO API.
This patch also unhardcode the GPIO we request and use
the one we defined in the button driver.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we have removed all warnings from the ar7 board code we can use
-Werror like on other MIPS boards.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following build failure when CONFIG_SERIAL_8250
is not enabled in the kernel configuration:
arch/mips/ar7/built-in.o: In function 'ar7_register_devices':
platform.c:(.init.text+0x61c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x61c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'
platform.c:(.init.text+0x68c): undefined reference to 'early_serial_setup'
platform.c:(.init.text+0x68c): relocation truncated to fit: R_MIPS_26 against 'early_serial_setup'
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following build warning:
arch/mips/ar7/memory.c: In function 'memsize':
arch/mips/ar7/memory.c:55: warning: passing argument 1 of 'writel' makes integer from pointer without a cast
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some SiliconImage PCIe SATA controlers are not detected when the bus
numbers differ.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current interrupt handling code for the MSP4200 always masks an
interrupt before acknowledging it. This is not required, as that will be
handled by the level interrupt handler. This change simplifies the MSP4200
code to remove the masking in the ack routine, and makes sure that the
minimum required operation is performed for masking and acking, rather
than always both masking and acking the interrupt.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Trying to build a PMC-Sierra MSP4200 VoIP gateway defconfig will not work
since MIPS34K_MISSED_ITLB_WAR is not defined for all boards supported
within pmc-serria/msp71xx. This patch defines MIPS34K_MISSED_ITLB_WAR to
prevent such build failures:
CHK include/linux/version.h
CHK include/linux/utsrelease.h
SYMLINK include/asm -> include/asm-mips
CC arch/mips/kernel/asm-offsets.s
In file included fromlinux-msp71xx/linux-2.6.29/arch/mips/include/asm/bitops.h:24,
from include/linux/bitops.h:17,
from include/linux/kernel.h:15,
from include/linux/sched.h:52,
from arch/mips/kernel/asm-offsets.c:13:
linux-msp71xx/linux-2.6.29/arch/mips/include/asm/war.h:241:2: error: #error Check setting of MIPS34K_MISSED_ITLB_WAR for your
platform
This fixes a compile error when building for the MSP4200 boards. Identical
patches to fix this were send by
Florian Fainelli <florian@openwrt.org>
Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Trying to build MSP4200 VoIP defconfig also fails on msp_irq_slp.c with a
non-existing reference to mask_slp_irq, which is in turn mask_msp_slp_irq.
Passed that, we will also miss a comma when calling
set_irq_chip_and_handler. This patch fixes both issues.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loading of modules with unresolved weak symbols fails on MIPS
since '88173507e4fc1e7ecd111b0565e8cba0cb7dae6d'.
Modules: handle symbols that have a zero value
The module subsystem cannot handle symbols that are zero. If symbols
are present that have a zero value then the module resolver prints out a
message that these symbols are unresolved.
We have to use IS_ERR_VALUE() to check that a symbol has been resolved
or not.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit fc03bc1715ca0ad4ccfe97aab16bcc9e7129c1a4 breaks when SMTC support
is enabled on Malta.
Signed-off-by: Raghu Gandham <raghu@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The resume() implementation octeon_switch.S examines the saved cp0_status
register. We were clobbering the entire pt_regs structure in kernel
threads leading to random crashes.
When switching away from a kernel thread, the saved cp0_status is examined
and if bit 30 is set it is cleared and the CP2 state saved into the pt_regs
structure. Since the kernel thread stack overlaid the pt_regs structure
this resulted in a corrupt stack. When the kthread with the corrupt stack
was resumed, it could crash if it used any of the data in the stack that was
clobbered.
We fix it by moving the kernel thread stack down so it doesn't overlay
pt_regs.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cc1: warnings being treated as errors
arch/mips/mipssim/sim_time.c: In function 'get_c0_compare_int':
arch/mips/mipssim/sim_time.c:103: warning: ISO C90 forbids mixed declarations and code
arch/mips/mipssim/sim_time.c:116: error: expected declaration or statement at end of input
make[1]: *** [arch/mips/mipssim/sim_time.o] Error 1
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix the pagefault oom path which does not drop mm->mmap_sem.
This was introduced by commit c7c1e3846b
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
On x86_64, percpu variables current_task and kernel_stack are used for
get_current() and current_thread_info() respectively and thus are
often used close to each other. Move definition of current_task to
kernel/cpu/common.c right above kernel_stack definition and align it
to cacheline so that they always fall into the same cacheline. Two
percpu variables defined there together - irq_stack_ptr and irq_count
- are also pretty hot and will benefit from sharing the cacheline.
For consistency, current_task definition for x86_32 is also moved to
kernel/cpu/common.c.
Putting current_task and kernel_stack into the same cacheline was
suggested by Linus Torvalds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
DECLARE/DEFINE_PER_CPU_PAGE_ALIGNED() put percpu variables in
.page_aligned section without adding any alignment restrictions.
Currently, this doesn't cause any problem because all users of the
macros have explicit page alignment and page-sized but it's much safer
to enforce page alignment from the macros. After all, it's what they
claim to do.
Add __aligned(PAGE_SIZE) to DECLARE/DEFINE_PER_CPU_PAGE_ALIGNED() and
drop explicit alignment from it users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
