Move HWMON platform definition from plat-s3c24xx to plat-samsung
and adjust mach-bast to use the new s3c_hwmon_set_platdata().
This allows usage of dev-hwmon by other Samsung SoCs.
Signed-off-by: Maurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
As of git commit 1844c9bc0b head64.S/head31.S
are not included in head.S anymore but build as an extra object. This breaks
shared kernel support because the .org statement in head64.S/head31.S for
CONFIG_SHARED_KERNEL=y will have a different effect. The end address of the
head.text section in head.o will be added to the .org value, to compensate
for this subtract 0x11000 to get the required value of 0x100000 again.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
strace may change the system call number, so regs->gprs[2] must not
be read before tracehook_report_syscall_entry(). This fixes a bug
where "strace -f" will hang after a vfork().
Cc: <stable@kernel.org>
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The ACPI spec tells us that the firmware will reenable SCI_EN on resume.
Reality disagrees in some cases. The ACPI spec tells us that the only way
to set SCI_EN is via an SMM call.
https://bugzilla.kernel.org/show_bug.cgi?id=13745 shows us that doing so
may break machines. Tracing the ACPI calls made by Windows shows that it
unconditionally sets SCI_EN on resume with a direct register write, and
therefore the overwhelming probability is that everything is fine with
this behaviour.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Anton Blanchard found that large POWER systems would occasionally
crash in the exception exit path when profiling with perf_events.
The symptom was that an interrupt would occur late in the exit path
when the MSR[RI] (recoverable interrupt) bit was clear. Interrupts
should be hard-disabled at this point but they were enabled. Because
the interrupt was not recoverable the system panicked.
The reason is that the exception exit path was calling
perf_event_do_pending after hard-disabling interrupts, and
perf_event_do_pending will re-enable interrupts.
The simplest and cleanest fix for this is to use the same mechanism
that 32-bit powerpc does, namely to cause a self-IPI by setting the
decrementer to 1. This means we can remove the tests in the exception
exit path and raw_local_irq_restore.
This also makes sure that the call to perf_event_do_pending from
timer_interrupt() happens within irq_enter/irq_exit. (Note that
calling perf_event_do_pending from timer_interrupt does not mean that
there is a possible 1/HZ latency; setting the decrementer to 1 ensures
that the timer interrupt will happen immediately, i.e. within one
timebase tick, which is a few nanoseconds or 10s of nanoseconds.)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: stable@kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch removes static of s5p6440_sysclass, s5p6442_sysclass,
and s5pv210_sysclass for defintion as extern.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The address ben@fluff.org is old, ben-linux@fluff.org has been in use
for a long time, and we should fixup all the occasions of the older
address to avoid confusion.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
For CPU-feature-specific code that touches performance-critical paths,
introduce a static patching version of [boot_]cpu_has(). This is run
at alternatives time and is therefore not appropriate for most
initialization code, but on the other hand initialization code is
generally not performance critical.
On gcc 4.5+ this uses the new "asm goto" feature.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1273135546-29690-2-git-send-email-avi@redhat.com>
According to datasheet GPG13-15 must be configured as input in NAND
boot mode, otherwise device will not be able to wake up
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If PM_H1940 is enabled, kernel _must_ be located upper then 0x30008000,
because this area (0x30000000-0x30100000) can be used by bootloader. If
kernel is located at 0x30008000, bootloader will corrupt kernel's code during
resume.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds additional LPC Controller DeviceIDs for the Intel Cougar
Point PCH.
The DeviceIDs are defined and referenced as a range of values, the same
way Ibex Peak was implemented.
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
pci_config_lock must be a real spinlock in preempt-rt. Convert it to
raw_spinlock. No change for !RT kernels.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In mmp2, 6 banks of GPIO registers are supported. So we can support 192
GPIO pins at most.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.
The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>
This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CM-X300 bootloader passes DRAM configuration information in ATAGS,
however, the first memory bank is reported at actual physical address 0x8000000.
Use the configuration information supplied by the bootloader and
cope with the necessity to have PHYS_ADDR=0xa0000000.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful. Move
it to mach/Kconfig.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
