Interface should be visible even if resource allocation fails.
netif_device_attach should be called for every netif_device_detach.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add debug print in driver, can be tuned by ethtool msg level
callback.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o USE/Read IDC defined timeout value from ROM.
o While resetting chip, don't wait for other pci-func to respond,
more than reset_ack_timeo seconds,
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect offset calculation and remove unnecessary remap
of the region in bar 0 to access onchip memory.
This was leading to read incorrect values by debug tools.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All QLogic converged NICs have 128-bit 128MB on card memory.
Fix the limit check from 64MB to 128MB and remove unnecessary
64-bit read/write checks.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the access by tools for hardware queue engine and handle it
separately than other block registers, otherwise incorrect data
is returned.
Signed-off-by: Dhananjay Phadke <dhananjay.phadke@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use the normal hotplug mechanism because it doesn't work. It will
load the module some time after the device appears, but that's not good
enough for us -- we need the driver loaded _immediately_ because otherwise
the NIC driver may just abort and then the phy 'device' goes away.
[bwh: s/phy/mdio/ in module alias, kerneldoc for struct mdio_device_id]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some defines used by all agn devices, but the definitions were in
iwl-4965-hw.h, move those to iwl-agn-hw.h which is the better place for
those.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In iwl_rx_queue_reset(), we didn't clear the rxq->queue[]. This might
cause the same rxb appears on multiple places in rxq->queue. Although
this won't cause any problem because of the read and write pointers
protection in rxq, we'd better clear it to avoid misleading.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Module parameters used to be defined in both iwl-5000.c and iwl-4965.c,
after the code re-structure, merge into iwl-agn.c for easy to read and
maintenance.
Number of module parameters are deprecated after this merge. These are also
scheduled for removal by 2.6.40.
The current supported parameters are:
parm: debug50:50XX debug output mask (deprecated) (uint)
parm: debug:debug output mask (uint)
parm: swcrypto50:using crypto in software (default 0 [hardware])
(deprecated) (bool)
parm: swcrypto:using crypto in software (default 0 [hardware]) (int)
parm: queues_num50:number of hw queues in 50xx series (deprecated)
(int)
parm: queues_num:number of hw queues. (int)
parm: 11n_disable50:disable 50XX 11n functionality (deprecated) (int)
parm: 11n_disable:disable 11n functionality (int)
parm: amsdu_size_8K50:enable 8K amsdu size in 50XX series (deprecated)
(int)
parm: amsdu_size_8K:enable 8K amsdu size (int)
parm: fw_restart50:restart firmware in case of error (deprecated) (int)
parm: fw_restart:restart firmware in case of error (int)
parm: disable_hw_scan:disable hardware scanning (default 0) (int)
Remove "antenna" module parameter, it is not being used in "agn" driver.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We used to free all the Tx queues memory when interface is brought
down and reallocate them again in interface up. This requires
order-4 allocation for txq->cmd[]. In situations like s2ram, this
usually leads to allocation failure in the memory subsystem. The
patch fixed this problem by allocating the Tx queues memory only at
the first time. Later iwl_down/iwl_up only initialize but don't
free and reallocate them. The memory is freed at the device removal
time. BTW, we have already done this for the Rx queue.
This fixed bug https://bugzilla.kernel.org/show_bug.cgi?id=15551
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When collecting tx data for non-aggregation packets in rate scaling, if
the tx data matches "other table", it still uses current table to update
the stats and calculate average throughput in function rs_collect_tx_data().
This can mess up the rate scaling data structure and cause a kernel panic
in a BUG_ON statement in rs_rate_scale_perform().
To fix this bug, we pass table pointer instead of window pointer (pointed
to by table pointer) to function rs_collect_tx_data() so that the table
being used is consistent.
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Henry Zhang <hongx.c.zhang@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
- Patch adds support to enable PCI SRIOV in the driver and changes to handle initialization of PCI virtual functions.
- Function handler to change mac addresses for VF from its corresponding PF.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding GRO support on top of the HW LRO (TPA) support –
there is no measurable performance drawback of adding GRO
on top of it, and it allows better performance when LRO (TPA)
is turned off for virtualization or bridging.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix formatting on r8169 printk
Brandon Philips noted that I had a spacing issue in my printk for the
last r8169 patch that made it quite ugly. Fix that up and add the PFX
macro to it as well so it looks like the other r8169 printks
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a reset is performed, rtl8169_rx_interrupt() is called from
process context instead of softirq context. Special care must be taken
to call appropriate network core services (netif_rx() instead of
netif_receive_skb()). VLAN handling also corrected.
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Diagnosed-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acenic wrongly assumes that zero is an invalid dma address (calls
dma_unmap_page for only non zero dma addresses). Zero is a valid dma
address on some architectures. The dma length can be used here.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
bond_uninit() is invoked with rtnl_lock held, when it does destroy_workqueue()
which will potentially flush all works in this workqueue, if we hold rtnl_lock
again in the work function, it will deadlock.
So move destroy_workqueue() to destructor where rtnl_lock is not held any more,
suggested by Eric.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Jiri Pirko <jpirko@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac uses crc32 functions so it needs to select CRC32.
Fixes build error:
drivers/built-in.o: In function `dwmac1000_set_filter':
dwmac1000_core.c:(.text+0x3c380): undefined reference to `crc32_le'
dwmac1000_core.c:(.text+0x3c384): undefined reference to `bitrev32'
Signed-off-by: Carmelo Amoroso <carmelo.amoroso@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan traffic on big endian architecture is broken.
Need to swap the vid before giving packet to stack.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While ar9170's USB transport packet size is currently set to 8KiB,
the PHY is capable of receiving AMPDUs with up to 64KiB.
Such a large frame will be split over several rx URBs and
exceed the previously allocated space for rx stream reconstruction.
This patch increases the buffer size to 64KiB which is
in fact the phy & rx stream designed size limit.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=15591
Reported-by: Christian Mehlis <mehlis@inf.fu-berlin.de>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 skips drop_unencrypted checks if the driver/firmware has
already taken care of this. In case of ath9k, we must not indicate
that the frame was decrypted if no decryption was actually done.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set IEEE80211_HW_RX_INCLUDES_FCS to indicate that
the FCS is present in RX frames. Also, remove a redundant
assignment of skb length and include the FCS_LEN
when checking padding.
Fixing this issue makes TKIP work.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_status and ath_rx_status data are only necessary for a short
time, until they have been processed and converted into mac80211 data
structures.
Because of that, it makes no sense to keep them tied to the DMA
descriptor, that only wastes precious memory.
This patch allocates the data on stack in the functions that call the
conversion functions from ath9k_hw.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_rx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate rx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch passes in a pointer to the ath_tx_status data structure for
functions that need it, instead of letting them grab it directly from
the ath_desc struct. This is useful for making it possible to allocate
the intermediate tx status data separately.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not setting the opmode properly during initialization
results in the firmware sending up a bunch of packets
before add_interface() has been called, for the first
interface.
This patch fixes the issue by setting the initial mode
to 'managed'.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stop/restart TX queues when the internal SKB
queue is full. This helps handle TX better
under heavy load.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
