When starting an aggregation session, the swq_id is generated in function
iwl_virtual_agg_queue_num() where the first parameter is supposed to be
the Access Class, but it used the tx fifo ID instead. This means the AC
value stored in swq_id is incorrect. To test this, look at the tx_queue
file in debugfs while transmitting Best Effort flow (ac=2), it shows:
hwq 10: read=0 write=0 stop=0 swq_id=0xa9 (ac 1/hwq 10)
After this fix, it will show:
hwq 10: read=0 write=0 stop=0 swq_id=0xaa (ac 2/hwq 10)
Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
We removed resetting of PCI_RETRY_TIMEOUT register
in merge of suspend resume work.
'Suspend and resume' resets the PCI configuration space, so we
have to disable the RETRY_TIMEOUT register again here.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
IEEE80211_CONF_SHORT_SLOT_TIME is no longer a possible setting in
ieee80211_conf->flags
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The low level transmission function is performed at uCode layer
for all the "agn" NICs, there is no statistics information available
for mac80211 get_stats() call. Remove the callback function to
avoid misleading information that returned success when indeed it is not
supported. Now return "not supported".
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Patch "iwlwifi: work around passive scan issue" was merged into
wireless-2.6, but touched a lot of code since modified (and moved)
in wireless-next-2.6. This caused some conflicts.
Conflicts:
drivers/net/wireless/iwlwifi/iwl-scan.c
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Some firmware versions don't behave properly when
passive scanning is requested on radar channels
without enabling active scanning on receiving a
good frame. Work around that issue by asking the
firmware to only enable the active scanning after
receiving a huge number of good frames, a number
that can never be reached during our dwell time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
when we fall back to buffered write from direct write, we call
__generic_file_aio_write() but that will end up doing direct write
even we are only prepared to do buffered write because the file
has the O_DIRECT flag set. This is a fix for
https://bugzilla.novell.com/show_bug.cgi?id=591039
revised with Joel's comments.
Signed-off-by: Li Dongyang <lidongyang@novell.com>
Acked-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (27 commits)
MIPS: Loongson 2F: Fix of problems introduced by -mfix-loongson2f-jump
MIPS: Loongson-2F: Use CONFIG_CPU_JUMP_WORKAROUNDS to control workarounds.
MIPS: Loongson 2F: Enable fixups of the latest binutils
MIPS: Loongson: Add CPU_LOONGSON2F_WORKAROUNDS
MIPS: Kconfig: Make Broadcom SoC support naming consistent
MIPS: BCM63xx: Update defconfig
MIPS: oprofile: Fix breakage when CONFIG_OPROFILE=m
STAGING: octeon-ethernet: Use proper phy addresses for Movidis hardware.
NET: mdio-octeon: Enable the hardware before using it.
I2C: Fix section mismatch errors in i2c-octeon.c
MIPS: Loongson: Fix LOONGSON_ADDRWIN_CFG macro.
MIPS: Loongson: Fix phys_mem_access_prot() check
MIPS: Loongson: Fix find_vga_mem_init()
MIPS: Loongson: Fix typo in gdium mach type string.
MIPS: Use CKSEG1ADDR for uncached handler
MIPS: Check for accesses beyond the end of the PGD.
MIPS: Use uasm_i_ds{r,l}l_safe() instead of uasm_i_ds{r,l}l() in tlbex.c
MIPS: Add uasm_i_dsrl_safe() and uasm_i_dsll_safe() to uasm.
MIPS: die() does not call die notifier chain
MIPS: Swarm, Littlesur: Enable PATA platform driver.
...
As documented in the Loongson 2F User Manual [2, 3], the old Loongson2F
series (2F01 / 2F02) have the NOP & JUMP issues which requires workarounds
in the kernel and binutils. This issue has been rectified in Loongson 2F
series 2F03 so no workarounds needed.
Now that the workarounds [1] adding the the -mfix-loongson2f-nop and
-mfix-loongson2f-jump options have been comitted to the binutils the CVS
repository), we can add the workarounds in the kernel.
The workarounds have no significant side effect on the system but may
decrease performance so we control them through a a new
CPU_LOONGSON2F_WORKAROUNDS config option allowing the users to only enable
it as necessary.
[1] "Fixups of Loongson2F" patch for binutils(actually for gas)
http://sourceware.org/ml/binutils/2009-11/msg00387.html
[2] Chapter 15 of "Loongson2F User Manual"(Chinese Version)
http://www.loongson.cn/uploadfile/file/200808211
[3] English Version of the above chapter 15
http://groups.google.com.hk/group/loongson-dev/msg/e0d2e220958f10a6?dmode=source
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1105/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 7fe2b3190b fixed possible
misordering of completion asts (casts) and blocking asts (basts)
for kernel locks. This patch does the same for locks taken by
user space applications.
Signed-off-by: David Teigland <teigland@redhat.com>
"MIPS: Calculate proper ebase value for 64-bit kernels"
9af43ea080dd5d6c7b34f38261780e5dd43537bc (lmo) rsp.
f6be75d03c (kernel.org) broke some 64-bit
MIPS systems.
Before this we were using XKPHYS/cached as ebase and computed the uncached
xphsys/unchached address for that area. After that commit ebase became a
32-bit compat address and convert does not work anymore. We now should use
CKSEG1 for this. CKSEG1ADDR does just that in 32-bit and 64-bit.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
To: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1149/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For some combinations of PAGE_SIZE and vmbits, it is possible to have
userspace access that are beyond what is covered by the PGD, but within
vmbits. Such an access would cause the TLB refill handler to load garbage
values for PMD and PTE potentially giving userspace access to parts of the
physical address space to which it is not entitled.
In the TLB refill hot path, we add a single dsrl instruction so we can
check if any bits outside of the range covered by the PGD are set. In
the vmalloc side we then separate the bad case from the normal vmalloc
case and call tlb_do_page_fault_0 if warranted. This slows us down a
bit, but has the benefit of yielding deterministic behavior.
[Ralf: Fixed build error for 32-bit kernels.]
[Ralf: Folded lmo commit c8c0e22b2aa3982852b44279638ef37f9aa31b7d into this
commit.]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1152/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
The MIPS implementation of die() forgets to call notify_die() and thus notifiers
registered via register_die_notifier() are not called. This results in kgdb not
being activated on exceptions.
The only subtlety is that notify_die declares its regs argument w/o const, so
the const had to be removed from mips die() as well.
[Ralf: Fixed build error for SGI IP22 and IP28 platforms.]
Signed-off-by: Yury Polyanskiy <ypolyans@princeton.edu>
Cc: linux-mips@linux-mips.org
Patchworks: http://patchwork.linux-mips.org/patch/1142/
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
Same issues as SD card detection: One of both is always triggering and the
handlers take care to shut it up and enable the other. To avoid messages
about "unbalanced interrupt enable/disable" they must not be automatically
enabled when initally requested.
This was not an issue with the db1200_defconfig due to fortunate timings;
on a build without network chip support the warnings appear.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/1133/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| arch/mips/pci/pci-sb1250.c: In function sb1250_pcibios_init:
| arch/mips/pci/pci-sb1250.c:257: warning: assignment makes integer from pointer without a cast
| arch/mips/pci/pci-sb1250.c:285: error: MAX_NR_CONSOLES undeclared (first use in this function)
| arch/mips/pci/pci-sb1250.c:285: error: (Each undeclared identifier is reported only once
| arch/mips/pci/pci-sb1250.c:285: error: for each function it appears in.)
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1136/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|arch/mips/sibyte/swarm/setup.c:153:
| warning: large integer implicitly truncated to unsigned type
The field was changed in d9b26352 aka ("x86, setup: Store the boot
cursor state"). This patch changes the values back they way they were
before this extra field got introduced.
While here, the other two boards are also converted to C99 initializer.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1137/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the 64-bit kernel we use swapper_pg_dir for three different things.
1) xuseg mappings for kernel threads.
2) vmap mappings for all kernel-space accesses in xkseg.
3) vmap mappings for kernel modules in ksseg (kseg2).
Due to how the TLB refill handlers work, any mapping established in
xkseg or ksseg will also establish a xuseg mapping that should never
be used by the kernel.
In order to be able to use exceptions to trap NULL pointer
dereferences, we need to ensure that nothing is mapped at address
zero. Since vmap mappings in xkseg are reflected in xuseg, this means
we need to ensure that there are no vmap mappings established at the
start of xkseg. So we move back VMALLOC_START to avoid establishing
vmap mappings at the start of xkseg.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1129/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
commit 5a0e3ad6af
Author: Tejun Heo <tj@kernel.org>
Date: Wed Mar 24 17:04:11 2010 +0900
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h
Since a while the few headers included don't drag in <linux/kernel.h>
anymore, thus no more prototype of printk() resulting in:
CC arch/mips/nxp/pnx8550/common/reset.o
/home/ralf/src/linux/upstream-linus/arch/mips/nxp/pnx8550/common/reset.c: In function 'pnx8550_machine_restart':
/home/ralf/src/linux/upstream-linus/arch/mips/nxp/pnx8550/common/reset.c:31: error: implicit declaration of function 'printk'
/home/ralf/src/linux/upstream-linus/arch/mips/nxp/pnx8550/common/reset.c:33: error: 'NULL' undeclared (first use in this function)
/home/ralf/src/linux/upstream-linus/arch/mips/nxp/pnx8550/common/reset.c:33: error: (Each undeclared identifier is reported only once
/home/ralf/src/linux/upstream-linus/arch/mips/nxp/pnx8550/common/reset.c:33: error: for each function it appears in.)
make[3]: *** [arch/mips/nxp/pnx8550/common/reset.o] Error 1
Fixed by including <linux/kernel.h>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Smatch complains because "lkb" is never NULL. Looking at it, the original
code actually adds the new element to the end of the list fine, so we can
just get rid of the if condition. This code is four years old and no one
has complained so it must work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David Teigland <teigland@redhat.com>
Commit 6f461f6c7c
("e1000e: enable/disable ASPM L0s and L1 and ERT according to hardware errata")
oopses on one of my ppc64 boxes with a NULL pointer (0x4a):
Unable to handle kernel paging request for data at address 0x0000004a
Faulting instruction address: 0xc0000000004d2f1c
cpu 0xe: Vector: 300 (Data Access) at [c000000bec1833a0]
pc: c0000000004d2f1c: .e1000e_disable_aspm+0xe0/0x150
lr: c0000000004d2f0c: .e1000e_disable_aspm+0xd0/0x150
dar: 4a
[c000000bec1836d0] c00000000069b9d8 .e1000_probe+0x84/0xe8c
[c000000bec1837b0] c000000000386d90 .local_pci_probe+0x4c/0x68
[c000000bec183840] c0000000003872ac .pci_device_probe+0xfc/0x148
[c000000bec183900] c000000000409e8c .driver_probe_device+0xe4/0x1d0
[c000000bec1839a0] c00000000040a024 .__driver_attach+0xac/0xf4
[c000000bec183a40] c000000000409124 .bus_for_each_dev+0x9c/0x10c
[c000000bec183b00] c000000000409c1c .driver_attach+0x40/0x60
[c000000bec183b90] c0000000004085dc .bus_add_driver+0x150/0x328
[c000000bec183c40] c00000000040a58c .driver_register+0x100/0x1c4
[c000000bec183cf0] c00000000038764c .__pci_register_driver+0x78/0x128
Seems like pdev->bus->self == NULL. I haven't touched pci in a long time
so I'm trying to remember what this means (no pcie bridge perhaps?)
The patch below fixes the oops for me.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous patch "mac80211: notify driver about
IBSS status" left a problem -- when we merge with
a new BSSID, we never tell the driver that we left
the old one. Fix that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reporting Tx status, indicate that only one rate was used.
Otherwise, the rate is frozen at rate index 0 (i.e. 1Mb/s).
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
-f, -c 1, -R are now useless for trace events recording, moreover
-M is useless and event hurts.
Remove them from the documentation examples and from record scripts.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Various SCSI trace enhancements:
- Display data and protection information scatterlist lengths in the
trace output
- Add support for VERIFY and WRITE SAME commands and decode the UNMAP
bit if applicable
- Add decoding of the PROTECT field for READ/VERIFY/WRITE/WRITE SAME
commands as well as the EXPECTED INITIAL REFERENCE TAG field for
their 32-byte variants
- Decode READ CAPACITY(16), GET LBA STATUS, and UNMAP
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
