All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "ath9k_htc: Handle WMI timeouts properly" introduced
a race condition in WMI command processing. The last issued command
should be stored _before_ issuing a WMI command. Not doing this
would result in the WMI event IRQ dropping correct command responses
as invalid.
Fix this race by storing the command id correctly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completion of WMI commands take a longer time
on some platforms. Increase the timeout value
to handle this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling the REGIN callback, processing
the incoming data first should be the preferred
mode of operation. Allocation of a new SKB may fail,
in which case, the URB will not be resubmitted.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So, apparently there is a USB reboot command
that the target accepts. Using this instead of
usb_reset_device() fixes the issue of "descriptor read error"
that pops up on repeated load/unload.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX callback, the HTC layer has to pass the
priv pointer that was registered during service initialization.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a code segment in configpciepowersave()
to make use of multiple register writes.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the USB device has been unplugged, there is
no point in trying to send commands to the target.
Fix this by denying all WMI commands in such a case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a recently introduced use-after-free regression
from "p54pci: prevent stuck rx-ring on slow system".
Hans de Goede reported a use-after-free regression:
>BUG: unable to handle kernel paging request at 6b6b6b6b
>IP: [<e122284a>] p54p_check_tx_ring+0x84/0xb1 [p54pci]
>*pde = 00000000
>Oops: 0000 [#1] SMP
>EIP: 0060:[<e122284a>] EFLAGS: 00010286 CPU: 0
>EIP is at p54p_check_tx_ring+0x84/0xb1 [p54pci]
>EAX: 6b6b6b6b EBX: df10b170 ECX: 00000003 EDX: 00000001
>ESI: dc471500 EDI: d8acaeb0 EBP: c098be9c ESP: c098be84
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
>Process swapper (pid: 0, ti=c098a000 task=c09ccfe0 task.ti=c098a000)
>Call Trace:
> [<e1222b02>] ? p54p_tasklet+0xaa/0xb5 [p54pci]
> [<c0440568>] ? tasklet_action+0x78/0xcb
> [<c0440ed3>] ? __do_softirq+0xbc/0x173
Quote from comment #17:
"The problem is the innocent looking moving of the tx processing to
after the rx processing in the tasklet. Quoting from the changelog:
This patch does it the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.
This is causing an issue with us referencing already freed memory,
because some skb's we transmit, we immediately receive back, such
as those for reading the eeprom (*) and getting stats.
What can happen because of the moving of the tx processing to after
the rx processing is that when the tasklet first runs after doing a
special skb tx (such as eeprom) we've already received the answer
to it.
Then the rx processing ends up calling p54_find_and_unlink_skb to
find the matching tx skb for the just received special rx skb and
frees the tx skb.
Then after the processing of the rx skb answer, and thus freeing
the tx skb, we go process the completed tx ring entires, and then
dereference the free-ed skb, to see if it should free free-ed by
p54p_check_tx_ring()."
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Trying to run izlisten (from lowpan-tools tests) on a device that does not
exists I got the oops below. The problem is that we are using get_dev_by_name
without checking if we really get a device back. We don't in this case and
writing to dev->type generates this oops.
[Oops code removed by Dmitry Eremin-Solenikov]
If possible this patch should be applied to the current -rc fixes branch.
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in for example pppoe introduce phonet_pernet and use it instead of calling
net_generic directly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are fitpc2 compatible boards that hang with existent i/o
operations order. Solution is to switch between writing to data
and command ports.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
tg3: Fix INTx fallback when MSI fails
MSI setup changes the value of irq_vec in struct tg3 *tp.
This attribute must be taken into account and restored before
we try to do a new request_irq for INTx fallback.
In powerpc, the original code was leading to an EINVAL return within
request_irq, because the driver was trying to use the disabled MSI
virtual irq number instead of tp->pdev->irq.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Watchdog configuration register and timer count register were interchanged,
causing wrong values to be written into both registers.
This caused watchdog triggered resets even if the watchdog was reset in time.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The sta->last_tx_rate is traditionally updated just before transmitting a
frame based on information from the rate control algorithm. However, for
hardware drivers with IEEE80211_HW_HAS_RATE_CONTROL this is not performed,
as the rate control algorithm is not executed, and because the used rate is
not known before the frame has actually been transmitted.
This causes atleast a fixed 1Mb/s to be reported to user space. A few other
instances of code also rely on this information.
Fix this by setting the sta->last_tx_rate in tx_status handling. There, look
for last rates entry set by the driver, and use that as value for
sta->last_tx_rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent PCMCIA_DEV_ID_MATCH_FUNC_ID from grabbing PFC-cards:
I changed the code, so that the first matching struct
pcmcia_device_id _PFC_ entry will mark the card has_pfc,
preventing PCMCIA_DEV_ID_MATCH_FUNC_ID to match.
[linux-pcmcia@lists.infradead.org: re-order commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
A new xfsqa test (226) with a prototype xfs_fsr change to try to
handle dynamic fork offsets better triggers an assertion failure
where the inode data fork is in btree format, yet there is room in
the inode for it to be in extent format. The two inodes look like:
before: ino 0x101 (target), num_extents 11, Max in-fork extents 6, broot size 40, fork offset 96
before: ino 0x115 (temp), num_extents 5, Max in-fork extents 3, broot size 40, fork offset 56
after: ino 0x101 (target), num_extents 5, Max in-fork extents 6, broot size 40, fork offset 96
after: ino 0x115 (temp), num_extents 11, Max in-fork extents 3, broot size 40, fork offset 56
Basically the target inode ends up with 5 extents in btree format,
but it had space for 6 extents in extent format, so ends up
incorrect. Notably here the broot size is the same, and that is
where the kernel code is going wrong - the btree root will fit, so
it lets the swap go ahead.
The check should not allow the swap to take place if the number of
extents while in btree format is less than the number of extents
that can fit in the inode in extent format. Adding that check will
prevent this swap and corruption from occurring.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This patch fixes few usability and configurability issues.
o All the cgroup based controller options are configurable from
"Genral Setup/Control Group Support/" menu. blkio is the only exception.
Hence make this option visible in above menu and make it configurable from
there to bring it inline with rest of the cgroup based controllers.
o Get rid of CONFIG_DEBUG_CFQ_IOSCHED.
This option currently does two things.
- Enable printing of cgroup paths in blktrace
- Enables CONFIG_DEBUG_BLK_CGROUP, which in turn displays additional stat
files in cgroup.
If we are using group scheduling, blktrace data is of not really much use
if cgroup information is not present. To get this data, currently one has to
also enable CONFIG_DEBUG_CFQ_IOSCHED, which in turn brings the overhead of
all the additional debug stat files which is not desired.
Hence, this patch moves printing of cgroup paths under
CONFIG_CFQ_GROUP_IOSCHED.
This allows us to get rid of CONFIG_DEBUG_CFQ_IOSCHED completely. Now all
the debug stat files are controlled only by CONFIG_DEBUG_BLK_CGROUP which
can be enabled through config menu.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Divyesh Shah <dpshah@google.com>
Reviewed-by: Gui Jianfeng <guijianfeng@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds support for Philips UDA1345 CODEC. The CODEC has only
volume control, de-emphasis, mute, DC filtering and power control features.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ipmr /proc interface (ip_mr_cache) can't be extended to dump routes
from any tables but the main table in a backwards compatible fashion since
the output format ends in a variable amount of output interfaces.
Introduce a new netlink interface to dump multicast routes from all tables,
similar to the netlink interface for regular routes.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Delay reporting for the three implemented DAC33 FIFO modes.
DAC33 has FIFO depth status register(s), but it can not be used, since
inside of pcm_pointer we can not send I2C commands.
Timestamp based estimation need to be used. The method of calculating
the delay depends on the active FIFO mode.
Bypass mode: FIFO is bypassed, report 0 as delay
Mode1: nSample fill mode. In this mode I need to use two timestamp
ts1: taken when the interrupt has been received
ts2: taken before writing to nSample register.
Interrupts are coming when DAC33 FIFO depth goes under alarm threshold.
Phase1: when we received the alarm threshold, but our workqueue has
not been executed (safeguard phase). Just count the played out
samples since ts1 and subtract it from the alarm threshold
value.
Phase2: During nSample burst (after writing to nSample register), count
the played out samples since ts1, count the samples received
since ts2 (in a burst). Estimate the FIFO depth using these and
alarm threshold value.
Phase3: Draining phase (after the burst read), count the played out
samples since ts1. Estimate the FIFO depth using the nSample
configuration and the alarm threshold value.
Mode7: Threshold based fill mode. In this mode one timestamp is enough.
ts1: taken when the interrupt has been received
Interrupts are coming when DAC33 FIFO depth reaches upper threshold.
Phase1: Draining phase (after the burst), counting the played out
samples since ts1, and subtract it from the upper threshold
value.
Phase2: During burst operation. Using the pre calculated time needed to
play out samples from the buffer during the drain period (from
upper to lower threshold), move the time window to cover the
estimated time from the burst start to the current time.
Calculate the samples played out since lower threshold and also
the samples received during the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When the DAC33 FIFO is in use the dai interface is running in
much higher speed than the sampling frequency.
Calculate the rate based on the internal base frequency and
the bclk divider.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need for calculations for FIFO bypass mode.
Just in case set the nsample maximum limit, which
has been done in the calculation phase.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Alarm threshold interrupt is triggered right after the
playback start.
This interrupt is recieved during the first burst period,
and caused the state machine to write additional nSample
command, which has to be avoided.
To fix this issue move the DAC33 interrupt unmasking
after we configured the PREFILL register with a small
delay.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Decouple rtnetlink address families from real address families in socket.h to
be able to add rtnetlink interfaces to code that is not a real address family
without increasing AF_MAX/NPROTO.
This will be used to add support for multicast route dumping from all tables
as the proc interface can't be extended to support anything but the main table
without breaking compatibility.
This partialy undoes the patch to introduce independant families for routing
rules and converts ipmr routing rules to a new rtnetlink family. Similar to
that patch, values up to 127 are reserved for real address families, values
above that may be used arbitrarily.
Signed-off-by: Patrick McHardy <kaber@trash.net>
fib_rules_register() duplicates the template passed to it without modification,
mark the argument as const. Additionally the templates are only needed when
instantiating a new namespace, so mark them as __net_initdata, which means
they can be discarded when CONFIG_NET_NS=n.
Signed-off-by: Patrick McHardy <kaber@trash.net>
This wires up CPU hotplug for SH-X3 SMP CPUs. Presently only secondary
cores can be hotplugged given that the boot CPU has to contend with the
broadcast timer. When real local timers are implemented this restriction
can be lifted.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a cache of the secondary CPUs idle loop for the cases where
hotplug simply enters a low power state instead of resetting or powering
off the core.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
smp_store_cpu_info() is presently flagged as __init, but is called by
start_secondary() which is __cpuinit, fix it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is just a cleanup and doesn't change how the code works.
The original code had a mix of returns and gotos so I changed everything
to just return directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
