When virtfn is used, we should use physfn to find correct drhd
-v2: add pci_physfn() Suggested by Roland Dreier <rdreier@cisco.com>
do can remove ifdef in dmar.c
-v3: Chris pointed out we need that for dma_find_matched_atsr_unit too
also change dmar_pci_device_match() static
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Roland Dreier <rdreier@cisco.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The widget connections of ADC of ALC880 and ALC2260 aren't initialized,
thus it might point to invalid pin. This can be a problem when mode=auto
and there is only one input pin. Then user can't change the connection
at all.
This patch adds the code to initialize the input pin connection of these
codecs.
Reference: Novell bnc#594363
https://bugzilla.novell.com/show_bug.cgi?id=594363
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While it may be efficient on real hardware, emulation of global
invalidations is very expensive as all shadow entries must be examined.
This patch changes the behaviour when caching mode is enabled (which is
the case when IOMMU emulation takes place). In this case, page specific
invalidation is used instead.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add reference counting to the netfilter LED target, to fix errors when
multiple rules point to the same target ("LED trigger already exists").
Signed-off-by: Adam Nielsen <a.nielsen@shikadi.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The CONFIG_PROVE_RCU option discovered a few invalid uses of
rcu_dereference() in netfilter. In all these cases, the code code
intends to check whether a pointer is already assigned when
performing registration or whether the assigned pointer matches
when performing unregistration. The entire registration/
unregistration is protected by a mutex, so we don't need the
rcu_dereference() calls.
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Tested-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
In caching-mode mappings of pages (changes from non-present to present)
require invalidation.
Currently, this IOTLB flush is performed with domain ID of zero.
This is not according to the VT-d spec and causes big problems for
emulating software.
This patch uses the correct domain ID in IOTLB flushes.
Device IOTLB invalidation is performed only on present to non-present
changes. This decision is now based on explicit parameter instead of
zero domain-ID.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
intel_map_sg used offset_pfn which was set to zero when invalidating the IOTLB.
intel_map_sg now uses size variable for this matter.
Signed-off-by: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Write combining/cached device mappings are not setting the shared bit,
which could potentially cause problems on SMP systems since the cache
lines won't participate in the cache coherency protocol.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The savesys_ipl_nss asm function is put into the .init.text section
however it is missing a ".previous" section which would restore the
previous section.
Luckily all functions in early.c are init functions so it doesn't
matter currently.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The default size of the vmalloc area is currently 1 GB. The memory resource
controller uses about 10 MB of vmalloc space per gigabyte of memory. That
turns a system with more than ~100 GB memory unbootable with the default
vmalloc size. It costs us nothing to increase the default size to some
more adequate value, e.g. 128 GB.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
commit 6a985c6194
([S390] s390: use change recording override for kernel mapping)
deactivated the change bit recording for the kernel mapping to
improve the performance. This works most of the time, but there
are cases (e.g. kernel runs in home space, futex atomic compare xcmg)
where we modify user memory with the kernel mapping instead of the
user mapping.
Instead of fixing these cases, this patch just deactivates change bit
override to avoid future problems with other kernel code that might
use the kernel mapping for user memory.
CC: stable@kernel.org
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a machine check interrupts the io interrupt handler on one of the
instructions between io_return and io_leave the critical section
cleanup code will move the return psw to io_work_loop. By doing that
the switch from the asynchronous interrupt stack to the process stack
is skipped. If e.g. TIF_NEED_RESCHED is set things break because
the scheduler is called with the asynchronous interrupts stack.
Moving the psw back to io_return instead fixes the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
"len" hasn't been properly range checked so we shouldn't use it as an
array offset. This can only be written to by root but it would still be
annoying to accidentally write more than 3 characters and corrupt your
memory.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In the default case the lock is not unlocked. The return is
converted to a goto, to share the unlock at the end of the function.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression E1;
identifier f;
@@
f (...) { <+...
* spin_lock_irq (E1,...);
... when != E1
* return ...;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Register the WM8750 as a SPI or I2C device. This patch mostly shuffles code
around. Hugely inspired by WM8753 which was already converted.
Also, this patch fixes the Jive and Spitz machine.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Corrected HP and mic pins for ALC269vb amic and dmic models.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALC269vb has an alternative HP pin 0x21 in addition.
Fix the parser to recognize it.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use a local mutex instead of BKL. This should suffice since each device
type has also its open_mutex.
Also, a bit of clean-up of the legacy device auto-loading code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
at91 slow-clock resume: Don't wait for a disabled PLL to lock.
We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When CFQ dispatches requests forcefully due to a barrier or changing iosched,
it runs through all cfqq's dispatching requests and then expires each queue.
However, it does not activate a cfqq before flushing its IOs resulting in
using stale values for computing slice_used.
This patch fixes it by calling activate queue before flushing reuqests from
each queue.
This is useful mostly for barrier requests because when the iosched is changing
it really doesnt matter if we have incorrect accounting since we're going to
break down all structures anyway.
We also now expire the current timeslice before moving on with the dispatch
to accurately account slice used for that cfqq.
Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
1) group_wait_time - This is the amount of time the cgroup had to wait to get a
timeslice for one of its queues from when it became busy, i.e., went from 0
to 1 request queued. This is different from the io_wait_time which is the
cumulative total of the amount of time spent by each IO in that cgroup waiting
in the scheduler queue. This stat is a great way to find out any jobs in the
fleet that are being starved or waiting for longer than what is expected (due
to an IO controller bug or any other issue).
2) empty_time - This is the amount of time a cgroup spends w/o any pending
requests. This stat is useful when a job does not seem to be able to use its
assigned disk share by helping check if that is happening due to an IO
controller bug or because the job is not submitting enough IOs.
3) idle_time - This is the amount of time spent by the IO scheduler idling
for a given cgroup in anticipation of a better request than the exising ones
from other queues/cgroups.
All these stats are recorded using start and stop events. When reading these
stats, we do not add the delta between the current time and the last start time
if we're between the start and stop events. We avoid doing this to make sure
that these numbers are always monotonically increasing when read. Since we're
using sched_clock() which may use the tsc as its source, it may induce some
inconsistency (due to tsc resync across cpus) if we included the current delta.
Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
These stats are useful for getting a feel for the queue depth of the cgroup,
i.e., how filled up its queues are at a given instant and over the existence of
the cgroup. This ability is useful when debugging problems in the wild as it
helps understand the application's IO pattern w/o having to read through the
userspace code (coz its tedious or just not available) or w/o the ability
to run blktrace (since you may not have root access and/or not want to disturb
performance).
Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This includes both the number of bios merged into requests belonging to this
cgroup as well as the number of requests merged together.
In the past, we've observed different merging behavior across upstream kernels,
some by design some actual bugs. This stat helps a lot in debugging such
problems when applications report decreased throughput with a new kernel
version.
This needed adding an extra elevator function to capture bios being merged as I
did not want to pollute elevator code with blkiocg knowledge and hence needed
the accounting invocation to come from CFQ.
Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
that include some minor fixes and addresses all comments.
Changelog: (most based on Vivek Goyal's comments)
o renamed blkiocg_reset_write to blkiocg_reset_stats
o more clarification in the documentation on io_service_time and io_wait_time
o Initialize blkg->stats_lock
o rename io_add_stat to blkio_add_stat and declare it static
o use bool for direction and sync
o derive direction and sync info from existing rq methods
o use 12 for major:minor string length
o define io_service_time better to cover the NCQ case
o add a separate reset_stats interface
o make the indexed stats a 2d array to simplify macro and function pointer code
o blkio.time now exports in jiffies as before
o Added stats description in patch description and
Documentation/cgroup/blkio-controller.txt
o Prefix all stats functions with blkio and make them static as applicable
o replace IO_TYPE_MAX with IO_TYPE_TOTAL
o Moved #define constant to top of blk-cgroup.c
o Pass dev_t around instead of char *
o Add note to documentation file about resetting stats
o use BLK_CGROUP_MODULE in addition to BLK_CGROUP config option in #ifdef
statements
o Avoid struct request specific knowledge in blk-cgroup. blk-cgroup.h now has
rq_direction() and rq_sync() functions which are used by CFQ and when using
io-controller at a higher level, bio_* functions can be added.
Signed-off-by: Divyesh Shah<dpshah@google.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'nouveau/for-airlied' of ../drm-nouveau-next: (21 commits)
drm/nouveau: bail out of auxch transaction if we repeatedly recieve defers
drm/nv50: implement gpio set/get routines
drm/nv50: parse/use some more de-magiced parts of gpio table entries
drm/nouveau: store raw gpio table entry in bios gpio structs
drm/nv40: Init some tiling-related PGRAPH state.
drm/nv50: Add NVA3 support in ctxprog/ctxvals generator.
drm/nv50: another dodgy DP hack
drm/nv50: punt hotplug irq handling out to workqueue
drm/nv50: preserve an unknown SOR_MODECTRL value for DP encoders
drm/nv50: Allow using the NVA3 new compute class.
drm/nv50: cleanup properly if PDISPLAY init fails
drm/nouveau: fixup the init failure paths some more
drm/nv50: fix instmem init on IGPs if stolen mem crosses 4GiB mark
drm/nv40: add LVDS table quirk for Dell Latitude D620
drm/nv40: rework lvds table parsing
drm/nouveau: detect vram amount once, and save the value
drm/nouveau: remove some unused members from drm_nouveau_private
drm/nouveau: Make use of TTM busy_placements.
drm/nv50: add more 0x100c80 flushy magic
drm/nv50: fix fbcon when framebuffer above 4GiB mark
...
The command processor (CP) fetches command buffers and
feeds the GPU. This patch requires the evergreen
family me and pfp ucode files.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initializes the gfx engine so accel can
eventually be used.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Allows *some* DP cards to keep working in some corner cases that most
people shouldn't hit. I hit it all the time with development, so this
can stay for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
