Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Extend slot-gpio to be used for host specific card detect interrupts
- Align to common busy polling behaviour for mmc ioctls
- Suggest the BFQ I/O scheduler to be built along with MMC/SD support
- Add devm_mmc_alloc_host() to enable further cleanups in host drivers
MMC host:
- atmel-mci: Fix race condition when stopping/starting a command
- dw_mmc-starfive: Add new driver to support the StarFive JH7110 variant
- dw_mmc-rockchip: Add support for the RK3588 variant
- jz4740: Add support for the vqmmc power supply
- meson-gx: Convert the DT bindings to the dt-schema
- meson-gx: Enable the platform interrupt to be used for card detect
- moxart: Set the supported maximum request/block/segment sizes
- renesas,sdhi: Add support for the RZ/V2M variants
- sdhci: Rework code to drop SDHCI_QUIRK_MISSING_CAPS
- sdhci-esdhc-imx: Improve tuning logic support
- sdhci-msm: Add support for the IPQ5332 and the IPQ9574 variants
- sdhci-of-dwcmshc: Add the missing device table IDs for acpi
- sdhci-of-dwcmshc: Improve clock support for the Rockchip variant
- sdhci-of-dwcmshc: Enable support of V4 host for the BlueField-3 variant
- sdhci-pxav2: Add support for the PXA168 V1 variant
- sdhci-pxav2: Add support for SDIO IRQs for the PXA168 V1 variant
- uniphier-sd: Add support for SD UHS-I speed modes"
* tag 'mmc-v6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
mmc: meson-gx: Use devm_platform_get_and_ioremap_resource()
mmc: meson-gx: constify member data of struct meson_host
mmc: meson-gx: use devm_clk_get_enabled() for core clock
mmc: core: fix return value check in devm_mmc_alloc_host()
dt-bindings: mmc: meson-gx: fix interrupt binding
mmc: meson-gx: support platform interrupt as card detect interrupt
dt-bindings: mmc: meson-gx: support specifying cd interrupt
mmc: core: support setting card detect interrupt from drivers
mmc: starfive: Add sdio/emmc driver support
dt-bindings: mmc: Add StarFive MMC module
dt-bindings: mmc: sdhci-msm: Allow 1 icc path
dt-bindings: mmc: rockchip-dw-mshc: Add RK3588 compatible string
mmc: core: Align to common busy polling behaviour for mmc ioctls
dt-bindings: mmc: Add resets property to cadence SDHCI binding
mmc: meson-gx: remove meson_mmc_get_cd
mmc: moxart: set maximum request/block/segment sizes
mmc: sdhci-brcmstb: Use devm_platform_get_and_ioremap_resource()
mmc: sdhci-of-dwcmshc: add the missing device table IDs for acpi
mmc: sdhci-of-dwcmshc: Update DLL and pre-change delay for rockchip platform
mmc: jz4740: Add support for vqmmc power supply
...
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
Per datasheet: maximum block length is 2048 bytes,
data length field is in bits 0-23 of the Data Length Register.
Also for DMA mode we have to take into account rx/tx buffers' sizes.
In my tests this change doubles SD card I/O performance on big files.
Before the change Linux used default request size of 4 KB.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Link: https://lore.kernel.org/r/20230210143843.369943-1-saproj@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge the mmc fixes for v6.2-rc[n] into the next branch, to allow them to
get tested together with the new mmc changes that are targeted for v6.3.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The original TPS65010 dependency was only needed for MACH_OMAP_H2,
which is now gone, but I messed up the conversion when I removed that
symbol.
Now the missing TPS65010 causes a boot failure on other machines
such as the SX1.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Fixes: 0d7bb85e94 ("ARM: omap1: remove unused board files")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This commit fixes a race between completion of stop command and start of a
new command.
Previously the command ready interrupt was enabled before stop command
was written to the command register. This caused the command ready
interrupt to fire immediately since the CMDRDY flag is asserted constantly
while there is no command in progress.
Consequently the command state machine will immediately advance to the
next state when the tasklet function is executed again, no matter
actual completion state of the stop command.
Thus a new command can then be dispatched immediately, interrupting and
corrupting the stop command on the CMD line.
Fix that by dropping the command ready interrupt enable before calling
atmci_send_stop_cmd. atmci_send_stop_cmd does already enable the
command ready interrupt, no further writes to ATMCI_IER are necessary.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20221230194315.809903-2-t.schramm@manjaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The devicetree bindings for this driver specify that the two allowed
clock names are io and core. Change this driver to look for io, but
allow any name if it fails for backwards compatibility. Follow the same
pattern used in sdhci-pxav3, but add support for EPROBE_DEFER.
Get rid of an unnecessary pdev->dev while we're at it.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-5-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PXA168 has a documented silicon bug that results in a data abort
exception when accessing the SDHCI_HOST_VERSION register on SDH2 and
SDH4 through a 16-bit read. Implement the workaround described in the
errata, which performs a 32-bit read from a lower address instead. This
is safe to use on all four SDH peripherals.
Signed-off-by: Doug Brown <doug@schmorgal.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230116194401.20372-4-doug@schmorgal.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_MISSING_CAPS is not needed because __sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with __sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Link: https://lore.kernel.org/r/20230113110011.129835-6-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230113110011.129835-5-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20230113110011.129835-4-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_MISSING_CAPS is not needed because sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with sdhci_read_caps().
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230113110011.129835-3-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHCI_QUIRK_MISSING_CAPS is not needed because __sdhci_read_caps() can be
called instead.
In preparation to get rid of SDHCI_QUIRK_MISSING_CAPS, replace
SDHCI_QUIRK_MISSING_CAPS with __sdhci_read_caps() for Ricoh SDHCI
controller.
__sdhci_read_caps() is also called from sdhci_setup_host() via
sdhci_read_caps(), however only the first call to __sdhci_read_caps() does
anything because after that host->read_caps has been set to true.
Note, __sdhci_read_caps() does more than just set host->caps, such as do a
reset, so calling __sdhci_read_caps() earlier could have unforeseen
side-effects. However the code flow has been reviewed with that in mind.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20230113110011.129835-2-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
USDHC IP has one limitation: the tuning circuit can't handle the async
sdio device interrupt correctly. When sdio device use 4 data lines,
async sdio interrupt will use the shared DAT[1], if enable auto tuning
circuit to check these 4 data lines, include the DAT[1], this circuit
will detect this interrupt, take this as data on DAT[1], and adjust the
delay cell wrongly, finally will cause the DATA/CMD CRC error.
So for SDIO device, only enable DAT[0] and CMD line for auto tuning.
To distinguish the card type during card init, involve init_card().
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221223025022.1893102-3-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All board support that was marked as 'unused' earlier can
now be removed, leaving the five machines that that still
had someone using them in 2022, or that are supported in
qemu.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull MMC and MEMSTICK updates from Ulf Hansson:
"MMC core:
- A few minor improvements and cleanups
MMC host:
- Remove some redundant calls to local_irq_{save,restore}()
- Replace kmap_atomic() with kmap_local_page()
- Take return values from mmc_add_host() into account
- dw_mmc-pltfm: Add support to configure clk-phase for socfpga
- hsq: Minimize latency by using a fifo to dispatch requests
- litex_mmc: Fixup corner case for polling mode
- mtk-sd: Add inline crypto engine clock control
- mtk-sd: Add support for the mediatek MT7986 variant
- renesas_sdhi: Improve reset from HS400 mode
- renesas_sdhi: Take DMA end interrupts into account
- sdhci: Avoid unnecessary update of clock
- sdhci: Fix an SD tuning issue
- sdhci-brcmst: Add Kamal Dasu as maintainer for the Broadcom driver
- sdhci-esdhc-imx: Improve tuning logic
- sdhci-esdhc-imx: Improve support for the imxrt1050 variant
- sdhci_f_sdh30: Add support for non-removable media
- sdhci_f_sdh30: Add support for the Socionext F_SDH30_E51 variant
- sdhci_f_sdh30: Add reset control support
- sdhci-msm: Add support for the Qcom SM8550/SM8350/SM6375 variants
- sdhci-msm: Add support for the Qcom MSM8976 variant
- sdhci-of-arasan: Add support for dynamic configuration
- sdhci-of-esdhc: Limit the clock frequency to confirm to spec
- sdhci-pci: Enable asynchronous probe
- sdhci-sprd: Improve card detection
- sdhci-tegra: Improve reset support
- sdhci-tegra: Add support to program MC stream ID
- sunplus-mmc: Add new mmc driver for the Sunplus SP7021 controller
- vub300: Fix warning splat for SDIO irq
MEMSTICK core:
- memstick: A few minor improvements and cleanups
CLK/IOMMU:
- clk: socfpga: Drop redundant support for clk-phase for the SD/MMC clk
- iommu: Add tegra specific helper to get stream_id"
* tag 'mmc-v6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (108 commits)
mmc: sdhci-sprd: Disable CLK_AUTO when the clock is less than 400K
mmc: sdhci-of-esdhc: Modify mismatched function name
memstick/mspro_block: Convert to use sysfs_emit()/sysfs_emit_at() APIs
mmc: sdhci-tegra: Issue CMD and DAT resets together
mmc: sdhci-tegra: Add support to program MC stream ID
mmc: sdhci-tegra: Separate Tegra194 and Tegra234 SoC data
mmc: sdhci-tegra: Sort includes alphabetically
iommu/tegra: Add tegra_dev_iommu_get_stream_id() helper
iommu: Add note about struct iommu_fwspec usage
mmc: sdhci-brcmstb: Resolve "unused" warnings with CONFIG_OF=n
dt-bindings: mmc: sdhci-msm: allow dma-coherent
dt-bindings: mmc: sdhci-msm: drop properties mentioned in common MMC
dt-bindings: mmc: sdhci-msm: cleanup style
dt-bindings: mmc: sdhci-am654: cleanup style
dt-bindings: mmc: sdhci: document sdhci-caps and sdhci-caps-mask
mmc: vub300: fix warning - do not call blocking ops when !TASK_RUNNING
MAINTAINERS: Update maintainer for SDHCI Broadcom BRCMSTB driver
mmc: sdhci-of-esdhc: limit the SDHC clock frequency
mmc: sdhci: Remove unneeded semicolon
mmc: core: Normalize the error handling branch in sd_read_ext_regs()
...
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
