As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv
-----BEGIN PGP SIGNATURE-----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=p6Xp
-----END PGP SIGNATURE-----
Merge tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
* parsers: ofpart: add workaround for #size-cells 0
* dt-bindings: partitions: Fix partition node name pattern
* dataflash: remove duplicate SPI ID table
Raw NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND driver changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
* Misc core fixes
SPI NOR driver changes:
* Spansion: Minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3MqwACgkQJWrqGEe9
VoTnsQf/bfzBqf0LbMBU7c+2VUjnE2dgLRssf0WqJB2INvDIAHQ8HKE2rqF6j1G0
wBnJOMf9fRpH6M3k45siNL37HPnacUq8QFZE3B3A3pUewWNtx5ldFrzT1awlsTu8
zIG37pnd2rJ+W3wfDDnNjTqQUfm3sLI7k/B3S8aqJA8i63DFLqih7ju0mgPVT7TX
C1X0VAx8gNMHQ6WqTX53SRZ4Ef9dJAcVwcFhkjHY09Q9VEW56ZlQ7uxyhwYqXjiJ
zDDGfPFhAsfwcykdFI3DtvNRT2bVbJl7N4GvTD8N4Rf+GIuMhVJnUjp5yTkAeEHx
HjXqBSI3ykHimsW7BRtE3HLR4775bA==
=FLt2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- parsers: ofpart: add workaround for #size-cells 0
- dt-bindings: partitions: Fix partition node name pattern
- dataflash: remove duplicate SPI ID table
Raw NAND core changes:
- Check the data only read pattern only once
- Prepare the late addition of supported operation checks
- Support for sequential cache reads
- Fix nand_chip kdoc
Raw NAND driver changes:
- Fsl_elbc: Propagate HW ECC settings to HW
- Marvell: Add missing layouts
- Pasemi: Don't use static data to track per-device state
- Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
- tmio_nand: Remove driver
- vf610_nfc: Use regular comments for functions
SPI-NAND driver changes:
- Add support for AllianceMemory AS5F34G04SND
- Macronix: use scratch buffer for DMA operation
NAND ECC changes:
- Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
SPI NOR changes:
- Misc core fixes
SPI NOR driver changes:
- Spansion: Minor fixes"
* tag 'mtd/for-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (33 commits)
mtd: parsers: ofpart: add workaround for #size-cells 0
mtd: rawnand: sunxi: Precompute the ECC_CTL register value
mtd: rawnand: sunxi: Embed sunxi_nand_hw_ecc by value
mtd: rawnand: sunxi: Update OOB layout to match hardware
mtd: spi-nor: Sort headers alphabetically
mtd: spi-nor: Fix shift-out-of-bounds in spi_nor_set_erase_type
mtd: nand: ecc-mtk: Add ECC support fot MT7986 IC
dt-bindings: mtd: mediatek,nand-ecc-engine: Add compatible for MT7986
dt-bindings: mtd: Split ECC engine with rawnand controller
mtd: rawnand: fsl_elbc: Propagate HW ECC settings to HW
mtd: spinand: Add support for AllianceMemory AS5F34G04SND
dt-bindings: mtd: partitions: Fix partition node name pattern
mtd: spi-nor: Create macros to define chip IDs and geometries
mtd: spi-nor: spansion: Make CFRx reg fields generic
mtd: spi-nor: spansion: Consider reserved bits in CFR5 register
mtd: spi-nor: core: fix implicit declaration warning
mtd: spinand: macronix: use scratch buffer for DMA operation
mtd: rawnand: Fix nand_chip kdoc
mtd: rawnand: vf610_nfc: use regular comments for functions
mtd: rawnand: Support for sequential cache reads
...
Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work falls
into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be moved
into read-only memory (i.e. const) The recent work with Rust has
pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only making
things safer overall. This is the contuation of that work (started
last release with kobject changes) in moving struct bus_type to be
constant. We didn't quite make it for this release, but the
remaining patches will be finished up for the release after this
one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCY/ipdg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynL3gCgwzbcWu0So3piZyLiJKxsVo9C2EsAn3sZ9gN6
6oeFOjD3JDju3cQsfGgd
=Su6W
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.3-rc1.
There's a lot of changes this development cycle, most of the work
falls into two different categories:
- fw_devlink fixes and updates. This has gone through numerous review
cycles and lots of review and testing by lots of different devices.
Hopefully all should be good now, and Saravana will be keeping a
watch for any potential regression on odd embedded systems.
- driver core changes to work to make struct bus_type able to be
moved into read-only memory (i.e. const) The recent work with Rust
has pointed out a number of areas in the driver core where we are
passing around and working with structures that really do not have
to be dynamic at all, and they should be able to be read-only
making things safer overall. This is the contuation of that work
(started last release with kobject changes) in moving struct
bus_type to be constant. We didn't quite make it for this release,
but the remaining patches will be finished up for the release after
this one, but the groundwork has been laid for this effort.
Other than that we have in here:
- debugfs memory leak fixes in some subsystems
- error path cleanups and fixes for some never-able-to-be-hit
codepaths.
- cacheinfo rework and fixes
- Other tiny fixes, full details are in the shortlog
All of these have been in linux-next for a while with no reported
problems"
[ Geert Uytterhoeven points out that that last sentence isn't true, and
that there's a pending report that has a fix that is queued up - Linus ]
* tag 'driver-core-6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (124 commits)
debugfs: drop inline constant formatting for ERR_PTR(-ERROR)
OPP: fix error checking in opp_migrate_dentry()
debugfs: update comment of debugfs_rename()
i3c: fix device.h kernel-doc warnings
dma-mapping: no need to pass a bus_type into get_arch_dma_ops()
driver core: class: move EXPORT_SYMBOL_GPL() lines to the correct place
Revert "driver core: add error handling for devtmpfs_create_node()"
Revert "devtmpfs: add debug info to handle()"
Revert "devtmpfs: remove return value of devtmpfs_delete_node()"
driver core: cpu: don't hand-override the uevent bus_type callback.
devtmpfs: remove return value of devtmpfs_delete_node()
devtmpfs: add debug info to handle()
driver core: add error handling for devtmpfs_create_node()
driver core: bus: update my copyright notice
driver core: bus: add bus_get_dev_root() function
driver core: bus: constify bus_unregister()
driver core: bus: constify some internal functions
driver core: bus: constify bus_get_kset()
driver core: bus: constify bus_register/unregister_notifier()
driver core: remove private pointer from struct bus_type
...
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmP3L4MACgkQJWrqGEe9
VoSVKgf+PUOBlR6U/QaNlzavYsTOz1Hgc9MjuC32CtStED8/uKfEG9odBRw1Fp+I
fNpgVnaWrU7KpW9yzsMTLQy//6lI/Hjn4KUMqKcsBmN3dOvzca60YrbehWLlrARb
exRDFvwuw6qZ0jRYMsKC9jsKhvU69TXnAWCdC+TSWRwfXci5dfjm3HxMNpRvT+PQ
q3sWqFMGj+omLOr/R+sBzhSV0WU1FpQsG9NB6I0VbFiJGy9YMMaI2tr/TKJyYeqM
CM0T3tccjKAajJ9i9qKIPZnRYWQYx/FyJ5Uyg6DRxjeoVjsFhGom1pQbH/2eHVs6
iND3n1yQCsnPaR/D7yRZgiTERQzqdw==
=psZR
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.3' into mtd/next
NAND core changes:
* Check the data only read pattern only once
* Prepare the late addition of supported operation checks
* Support for sequential cache reads
* Fix nand_chip kdoc
Raw NAND changes:
* Fsl_elbc: Propagate HW ECC settings to HW
* Marvell: Add missing layouts
* Pasemi: Don't use static data to track per-device state
* Sunxi:
- Fix the size of the last OOB region
- Remove an unnecessary check
- Remove an unnecessary check
- Clean up chips after failed init
- Precompute the ECC_CTL register value
- Embed sunxi_nand_hw_ecc by value
- Update OOB layout to match hardware
* tmio_nand: Remove driver
* vf610_nfc: Use regular comments for functions
SPI-NAND changes:
* Add support for AllianceMemory AS5F34G04SND
* Macronix: use scratch buffer for DMA operation
NAND ECC changes:
* Mediatek:
- Add ECC support fot MT7986 IC
- Add compatible for MT7986
- dt-bindings: Split ECC engine with rawnand controller
* small fixes on core and spansion driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmPgyGUACgkQS1VPR6WN
FOkv+AgAmqp68REEM7SicPy2dIy6fdLFOLjma9CSiWwGTMEJRM60ZBNFCJcAuUjD
1Sf+TCZEkBHc2crYCun5SqBErOA9oQCxI4nVtKZEQ9RyBklz/e5DsLONsVlLKrJU
lwemyeZ2tAV8023iBdjCi1nJ831eRmYipQMIEvr2xbOP/G95Ccc/wG6vKeMDi2QR
BxWdPD4XXvIVRY923nvnz9kK65QiqEQASJ8Rpf/AIYw+C/oukQFql8J3SMMs9kLH
DLagTnyhTx8qMd0V7Z6OVA3Ljf+bMd5gI7Z2fFQhErKo1mvT1Jw13sDQwxGGs+XS
9yxomEDKX+d/LdWEoZaSWFYwHVEixQ==
=fazc
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.3' into mtd/next
SPI NOR changes:
* small fixes on core and spansion driver.
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate subsystem
trees, but the majority is in the same branch, in order to better handle
dependencies between the patches and avoid breaking bisection.
Unfortunately that leads to merge conflicts against other changes in the
subsystem trees, but they should all be trivial to resolve by removing
the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed. The
only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users.
-----BEGIN PGP SIGNATURE-----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=WejQ
-----END PGP SIGNATURE-----
Merge tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC boardfile updates from Arnd Bergmann
"Unused boardfile removal for 6.3
This is a follow-up to the deprecation of most of the old-style board
files that was merged in linux-6.0, removing them for good.
This branch is almost exclusively dead code removal based on those
annotations. Some device driver removals went through separate
subsystem trees, but the majority is in the same branch, in order to
better handle dependencies between the patches and avoid breaking
bisection.
Unfortunately that leads to merge conflicts against other changes in
the subsystem trees, but they should all be trivial to resolve by
removing the files.
See commit 7d0d3fa733 ("Merge tag 'arm-boardfiles-6.0' of
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc") for the
description of which machines were marked unused and are now removed.
The only removals that got postponed are Terastation WXL (mv78xx0) and
Jornada720 (StrongARM1100), which turned out to still have potential
users"
* tag 'arm-boardfile-remove-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (91 commits)
mmc: omap: drop TPS65010 dependency
ARM: pxa: restore mfp-pxa320.h
usb: ohci-omap: avoid unused-variable warning
ARM: debug: remove references in DEBUG_UART_8250_SHIFT to removed configs
ARM: s3c: remove obsolete s3c-cpu-freq header
MAINTAINERS: adjust SAMSUNG SOC CLOCK DRIVERS after s3c24xx support removal
MAINTAINERS: update file entries after arm multi-platform rework and mach-pxa removal
ARM: remove CONFIG_UNUSED_BOARD_FILES
mfd: remove htc-pasic3 driver
w1: remove ds1wm driver
usb: remove ohci-tmio driver
fbdev: remove w100fb driver
fbdev: remove tmiofb driver
mmc: remove tmio_mmc driver
mfd: remove ucb1400 support
mfd: remove toshiba tmio drivers
rtc: remove v3020 driver
power: remove pda_power supply driver
ASoC: pxa: remove unused board support
pcmcia: remove unused pxa/sa1100 drivers
...
These "nvmem-cells" platform devices never get probed because there's no
platform driver for it and it's never used anywhere else. So it's a
waste of memory. These devices also cause fw_devlink to block nvmem
consumers of "nvmem-cells" partition from probing because the supplier
device never probes.
So stop creating platform devices for nvmem-cells partitions to avoid
wasting memory and to avoid blocking probing of consumers.
Reported-by: Maxim Kiselev <bigunclemax@gmail.com>
Fixes: bcdf0315a6 ("mtd: call of_platform_populate() for MTD partitions")
Signed-off-by: Saravana Kannan <saravanak@google.com>
Tested-by: Maksim Kiselev <bigunclemax@gmail.com>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Luca Weiss <luca.weiss@fairphone.com> # qcom/sm7225-fairphone-fp4
Link: https://lore.kernel.org/r/20230207014207.1678715-13-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a mechanism to handle the case in which partitions are present as
direct child of the nand controller node and #size-cells is set to <0>.
This could happen if the nand-controller node in the DTS is supposed to
have #size-cells set to 0, but for some historical reason/bug it was set
to 1 in the past, and the firmware (e.g. U-Boot) is adding the partition
as direct children of the nand-controller defaulting to #size-cells
being to 1.
This prevents a real boot failure on colibri-imx7 that happened during v6.1
development cycles.
Link: https://lore.kernel.org/all/Y4dgBTGNWpM6SQXI@francesco-nb.int.toradex.com/
Link: https://lore.kernel.org/all/20221202071900.1143950-1-francesco@dolcini.it/
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230124104444.330913-1-francesco@dolcini.it
The value computed by this function never changes for a given chip.
Compute the whole register value once up front, instead of every time
the ECC engine is enabled.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-4-samuel@sholland.org
The sunxi_nand_hw_ecc object is not shared, and it has the same lifetime
as the sunxi_nand_chip which points to it, so we can embed it in the
outer structure instead of using a pointer. This removes an unnecessary
memory allocation and simplifies the error handling code.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-3-samuel@sholland.org
When using the hardware ECC engine, the OOB data is made available in
the NFC_REG_USER_DATA registers, as one 32-bit word per ECC step. Any
additional bytes are only accessible through raw reads and software
descrambling. For efficiency, and to match the vendor driver, ignore
these extra bytes when using hardware ECC.
Note that until commit 34569d8695 ("mtd: rawnand: sunxi: Fix the size
of the last OOB region"), this extra free area was reported with length
zero, so this is not a functional change for any stable kernel user.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230204143520.9682-2-samuel@sholland.org
Sort headers alphabetically - it helps locating duplicates, and makes it
easier to figure out where to insert new headers. Alphabetic order should
also prove that each header is self-contained, i.e. can be included without
prerequisites.
Link: https://lore.kernel.org/r/20230202144628.14443-1-tudor.ambarus@linaro.org
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
spi_nor_set_erase_type() was used either to set or to mask out an erase
type. When we used it to mask out an erase type a shift-out-of-bounds
was hit:
UBSAN: shift-out-of-bounds in drivers/mtd/spi-nor/core.c:2237:24
shift exponent 4294967295 is too large for 32-bit type 'int'
The setting of the size_{shift, mask} and of the opcode are unnecessary
when the erase size is zero, as throughout the code just the erase size
is considered to determine whether an erase type is supported or not.
Setting the opcode to 0xFF was wrong too as nobody guarantees that 0xFF
is an unused opcode. Thus when masking out an erase type, just set the
erase size to zero. This will fix the shift-out-of-bounds.
Fixes: 5390a8df76 ("mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories")
Cc: stable@vger.kernel.org
Reported-by: Alexander Stein <Alexander.Stein@tq-group.com>
Signed-off-by: Louis Rannou <lrannou@baylibre.com>
Tested-by: Alexander Stein <Alexander.Stein@tq-group.com>
Link: https://lore.kernel.org/r/20230203070754.50677-1-tudor.ambarus@linaro.org
[ta: refine changes, new commit message, fix compilation error]
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
It is possible that current chip->ecc.engine_type value does not match to
configured HW value (if HW ECC checking and generating is enabled or not).
This can happen with old U-Boot bootloader version which either does not
initialize NAND (and let it in some default unusable state) or initialize
NAND with different parameters than what is specified in kernel DTS file.
So if kernel chose to use some chip->ecc.engine_type settings (e.g. from
DTS file) then do not depend on bootloader HW configuration and configures
HW ECC settings according to chip->ecc.engine_type value.
BR_DECC must be set to BR_DECC_CHK_GEN when HW is doing ECC (both
generating and checking), or to BR_DECC_OFF when HW is not doing ECC.
This change fixes usage of SW ECC support in case bootloader explicitly
enabled HW ECC support and kernel DTS file has specified to use SW ECC.
(Of course this works only in case when NAND is not a boot device and both
bootloader and kernel are loaded from different location, e.g. FLASH NOR.)
Fixes: f6424c22aa ("mtd: rawnand: fsl_elbc: Make SW ECC work")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230128134111.32559-1-pali@kernel.org
The INFO() macro defines an ID array and a couple of geometry
properties. Right now all its lines are duplicated twice because of the
INFO6() macro (for extended IDs) and soon as well we will need to add a
geometry parameter to include the number of banks.
In order to limit the code duplication, let's create a number of
intermediate macros which will facilitate defining high-level INFOX()
macros.
There is no functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20221215081241.407098-2-miquel.raynal@bootlin.com
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Cypress defines two flavors of configuration registers, volatile and
non volatile, and both use the same bit fields. Rename the bitfields in
the configuration registers so that they can be used for both flavors.
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-2-tudor.ambarus@linaro.org
CFR5[6] is reserved bit and must be always 1. Set it to comply with flash
requirements. While fixing SPINOR_REG_CYPRESS_CFR5V_OCT_DTR_{EN, DS}
definition, stop using magic numbers and describe the missing bit fields
in CFR5 register. This is useful for both readability and future possible
addition of Octal STR mode support.
Fixes: c3266af101 ("mtd: spi-nor: spansion: add support for Cypress Semper flash")
Cc: stable@vger.kernel.org
Reported-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Tested-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/linux-mtd/20230110164703.83413-1-tudor.ambarus@linaro.org
spi-nor/core.c needs to include linux/delay.h,
or it would raise below compile warning:
drivers/mtd/spi-nor/core.c: In function ‘spi_nor_soft_reset’:
drivers/mtd/spi-nor/core.c:2779:2: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
2779 | usleep_range(SPI_NOR_SRST_SLEEP_MIN, SPI_NOR_SRST_SLEEP_MAX);
| ^~~~~~~~~~~~
Fixes: d73ee7534c ("mtd: spi-nor: core: perform a Soft Reset on shutdown")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/20220923031457.56103-1-zengheng4@huawei.com
Now the rpcif_{en,dis}able_rpm() wrappers just take a pointer to a
device structure, there is no point in keeping them. Remove them, and
update the callers to call Runtime PM directly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d87aa5d7e4a39b18f7e2e0649fee0a45b45d371f.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Most rpcif_*() API functions do not need access to any other fields in
the rpcif structure than the device pointer. Simplify dependencies by
passing the device pointer instead.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/0460fe82ba348cedec7a9a75a8eff762c50e817b.1669213027.git.geert+renesas@glider.be
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
The mx35lf1ge4ab_get_eccsr() function uses an SPI DMA operation to
read the eccsr, hence the buffer should not be on stack. Since commit
380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
the kernel emmits a warning and blocks such operations.
Use the scratch buffer to get eccsr instead of trying to directly read
into a stack-allocated variable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/Y8i85zM0u4XdM46z@makrotopia.org
A number of device drivers reference CONFIG_ARM_S3C24XX_CPUFREQ or
similar symbols that are no longer available with the platform gone,
though the drivers themselves are still used on newer platforms,
so remove these hacks.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These comments are not quite in kernel-doc format and they don't need
to be, so just use "/*" comment markers for them. This prevents these
kernel-doc warnings:
drivers/mtd/nand/raw/vf610_nfc.c:210: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Read accessor for internal SRAM buffer
drivers/mtd/nand/raw/vf610_nfc.c:245: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Write accessor for internal SRAM buffer
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230113064004.24391-1-rdunlap@infradead.org
Add support for sequential cache reads for controllers using the generic
core helpers for their fast read/write helpers.
Sequential reads may reduce the overhead when accessing physically
continuous data by loading in cache the next page while the previous
page gets sent out on the NAND bus.
The ONFI specification provides the following additional commands to
handle sequential cached reads:
* 0x31 - READ CACHE SEQUENTIAL:
Requires the NAND chip to load the next page into cache while keeping
the current cache available for host reads.
* 0x3F - READ CACHE END:
Tells the NAND chip this is the end of the sequential cache read, the
current cache shall remain accessible for the host but no more
internal cache loading operation is required.
On the bus, a multi page read operation is currently handled like this:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR+tRR) -- DATA1_IN
00 -- ADDR2 -- 30 -- WAIT_RDY (tR+tRR) -- DATA2_IN
00 -- ADDR3 -- 30 -- WAIT_RDY (tR+tRR) -- DATA3_IN
Sequential cached reads may instead be achieved with:
00 -- ADDR1 -- 30 -- WAIT_RDY (tR) -- \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA1_IN \
31 -- WAIT_RDY (tRCBSY+tRR) -- DATA2_IN \
3F -- WAIT_RDY (tRCBSY+tRR) -- DATA3_IN
Below are the read speed test results with regular reads and
sequential cached reads, on NXP i.MX6 VAR-SOM-SOLO in mapping mode with
a NAND chip characterized with the following timings:
* tR: 20 µs
* tRCBSY: 5 µs
* tRR: 20 ns
and the following geometry:
* device size: 2 MiB
* eraseblock size: 128 kiB
* page size: 2 kiB
============= Normal read @ 33MHz =================
mtd_speedtest: eraseblock read speed is 15633 KiB/s
mtd_speedtest: page read speed is 15515 KiB/s
mtd_speedtest: 2 page read speed is 15398 KiB/s
===================================================
========= Sequential cache read @ 33MHz ===========
mtd_speedtest: eraseblock read speed is 18285 KiB/s
mtd_speedtest: page read speed is 15875 KiB/s
mtd_speedtest: 2 page read speed is 16253 KiB/s
===================================================
We observe an overall speed improvement of about 5% when reading
2 pages, up to 15% when reading an entire block. This is due to the
~14us gain on each additional page read (tR - (tRCBSY + tRR)).
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: JaimeLiao <jaimeliao.tw@gmail.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-4-miquel.raynal@bootlin.com
Add an empty envelope just to show how to add additional checks for new
operations. This is going to be used for sequential cached reads, which
require the page size to be known (and the discovery to be over), hence
the "late" designation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-3-miquel.raynal@bootlin.com
Instead of checking if a pattern is supported each time we need it,
let's create a bitfield that only the core would be allowed to fill at
startup time. The core and the individual drivers may then use it in
order to check what operation they should use. This bitfield is supposed
to grow over time.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Liao Jaime <jaimeliao.tw@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20230112093637.987838-2-miquel.raynal@bootlin.com
With the TMIO MFD drivers gone, the NAND support is also
obsolete and can be removed.
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Up to now the pasemi nand driver only supported a single device
instance. However the check for that was racy because two parallel calls
of pasemi_nand_probe() could pass the check
if (pasemi_nand_mtd)
return -ENODEV;
before any of them assigns a non-NULL value to it.
So rework the driver to make use of per-device driver data.
As an intended side effect the driver can bind more than one device and
also gets rid of the check
if (!pasemi_nand_mtd)
return 0;
in the remove callback that could only ever trigger after the above race
happened.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230102124051.1508424-1-u.kleine-koenig@pengutronix.de
Building with -Werror=override-init reveals that two patches added
the same device ID table to this driver:
drivers/mtd/devices/mtd_dataflash.c:946:27: error: initialized field overwritten [-Werror=override-init]
946 | .id_table = dataflash_spi_ids,
| ^~~~~~~~~~~~~~~~~
drivers/mtd/devices/mtd_dataflash.c:946:27: note: (near initialization for 'dataflash_driver.id_table')
Remove one of the copies.
Fixes: 27a030e872 ("mtd: dataflash: Add device-tree SPI IDs")
Fixes: ac4f83482a ("mtd: dataflash: Add SPI ID table")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221215164736.1315815-1-arnd@kernel.org
Each chip is required to have a unique CS number ("reg" property) in the
range 0-7, so there is no need to separately count the number of chips.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-4-samuel@sholland.org
If a chip fails to initialize, we need to clean up any chips that were
already initialized/registered.
Fixes: 1fef62c142 ("mtd: nand: add sunxi NAND flash controller support")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221229181526.53766-2-samuel@sholland.org
A missing layouts were added to the driver to support NAND flashes
with ECC layouts of 12 or 16 with page sized of 2048, 4096 or 8192.
Usually theses are rare layouts, but in Marvell AC5 driver, the ECC
level is set according to the spare area, so we may use these layouts
more frequently.
Signed-off-by: Aviram Dali <aviramd@marvell.com>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221216162715.3230766-1-vadym.kochan@plvision.eu
When MTD or MTD_CFI_GEOMETRY is disabled, the spi-intel driver
fails to build, as it includes the shared CFI header:
include/linux/mtd/cfi.h:62:2: error: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
62 | #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work.
linux/mtd/spi-nor.h does not actually need to include cfi.h, so
remove the inclusion here to fix the warning. This uncovers a
missing #include in spi-nor/core.c so add that there to
prevent a different build issue.
Fixes: e23e5a05d1 ("mtd: spi-nor: intel-spi: Convert to SPI MEM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Tokunori Ikegami <ikegami.t@gmail.com>
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221220141352.1486360-1-arnd@kernel.org
This fixes the following compile error on mips architecture with clang
version 16.0.0 reported by the 0-DAY CI Kernel Test Service:
ld.lld: error: undefined symbol: __udivdi3
referenced by scpart.c
mtd/parsers/scpart.o:(scpart_parse) in archive drivers/built-in.a
As a workaround this makes 'offs' a 32-bit type. This is enough, because
the mtd containing partition table practically does not exceed 1 MB. We
can revert this when the [Link] has been resolved.
Link: https://github.com/ClangBuiltLinux/linux/issues/1635
Fixes: 9b78ef0c79 ("mtd: parsers: add support for Sercomm partitions")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/805fe58e-690f-6a3f-5ebf-2f6f6e6e4599@gmail.com
The parts needs to be freed with all its elements, otherwise it will be
leaked.
Fixes: 00a3588084 ("mtd: parsers: add TP-Link SafeLoader partitions table parser")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221208113620.78855-1-yuancan@huawei.com
BFPT_DWORD() converts 1-based indexing to 0-based indexing for C arrays,
and is used in BFPT parse. Per JESD216F.02, the conversion is applicable
to other parameter tables than BFPT. This patch renames the macro to
SFDP_DWORD() so that we can use it for other parameter tables than BFPT.
Suggested-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Link: https://lore.kernel.org/r/e42feac840fe3a31187419e91b2d514d9f259d15.1672026365.git.Takahiro.Kuwano@infineon.com
* Fix refcount error in del_mtd_device()
* Fix possible resource leak in init_mtd()
* Set ROOT_DEV for partitions marked as rootfs in DT
* Describe marking rootfs partitions in the bindings
* Fix device name leak when register device failed in add_mtd_device()
* Try to find OF node for every MTD partition
* simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
* pxa2xx-flash maps: fix memory leak in probe
* BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
* lpddr2_nvm: Fix possible null-ptr-deref
* inftlcore: fix repeated words in comments
* lart: remove driver
* tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
* mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter to after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
* Fixed-partitions: Fix 'sercomm,scpart-id' schema
* Standardize the style in the examples
* Drop object types when referencing other files
* Argue in favor of keeping additionalProperties set to true
* NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
* Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
* Physmap: Reuse the generic definitions
* SPI-NOR: Drop common properties
* Sunxi-nand: Add an example to validate the bindings
* Onenand: Mention the expected node name
* Ingenic: Mark partitions in the controller node as deprecated
* NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
* Remove useless file about partitions
* Clarify all partition subnodes
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOOBbQACgkQJWrqGEe9
VoRB7wf9EY8IeRhumaeN9WT+VrmPxGOu61m/eilUK4xvgj6JX/yhYo/kKW9eEp+o
5I8JLimG6uo7rZNlbixGMbHd41aTu9MplLrTA42nzGadl3w4D8p9c1ic6sEiv7SI
qgnAbzq3FLUPDLLDV0IfrMQvsQgJkv3b+r8ShPt9uJy3cmnKQzOvIhs43wwLnOXp
NPiMbVjpS4FAmNvG7nI0xfcBLO/eFaTuQc+UyfP2SwkVIAN5xfUAwOPOHZWBstmR
zhJlHSFJWrg+J9T9bsRW7D5q/MVxqNsMH589c9aXHNqzgzZs2FTopDUf6cWwHr0f
2Ssot2naIdvU+eLGA12hDuUDDoRwKA==
=Igti
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core changes:
- Fix refcount error in del_mtd_device()
- Fix possible resource leak in init_mtd()
- Set ROOT_DEV for partitions marked as rootfs in DT
- Describe marking rootfs partitions in the bindings
- Fix device name leak when register device fails in add_mtd_device()
- Try to find OF node for every MTD partition
- simplify (a bit) code find partition-matching dynamic OF node
MTD driver changes:
- pxa2xx-flash maps: fix memory leak in probe
- BCM parser: refer to ARCH_BCMBCA instead of ARCH_BCM4908
- lpddr2_nvm: Fix possible null-ptr-deref
- inftlcore: fix repeated words in comments
- lart: remove driver
- tplink:
- Add TP-Link SafeLoader partitions table parser and bindings
- Describe TP-Link SafeLoader parser
- Describe TP-Link SafeLoader dynamic subpartitions
- mtdoops:
- Panic caused mtdoops to call mtdoops_erase function immediately
- Add mtdoops_erase function and move mtdoops_inc_counter after it
- Change printk() to counterpart pr_ functions
MTD binding cleanup:
- Fixed-partitions: Fix 'sercomm,scpart-id' schema
- Standardize the style in the examples
- Drop object types when referencing other files
- Argue in favor of keeping additionalProperties set to true
- NVMEM-cells:
- Inherit from MTD partitions
- Drop range property from example
- Partitions:
- Change qcom,smem-part partition type
- Constrain the list of parsers
- Physmap: Reuse the generic definitions
- SPI-NOR: Drop common properties
- Sunxi-nand: Add an example to validate the bindings
- Onenand: Mention the expected node name
- Ingenic: Mark partitions in the controller node as deprecated
- NAND:
- Standardize the child node name
- Drop common properties already defined in generic files
- nand-chip.yaml should reference mtd.yaml
- Remove useless file about partitions
- Clarify all partition subnodes
SPI NOR core changes:
- Add support for flash reset using the dt reset-gpios property.
- Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
- Bypass zero erase size in spi_nor_find_best_erase_type().
- Fix select_uniform_erase to skip 0 erase size
- Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described
solely by the flash's SFDP tables.
- Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
- Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP
discoverable.
SPI NOR manufacturer drivers changes:
- Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
- Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
- Micron - ST: Enable locking for mt25qu256a.
- Winbond: Add support for W25Q512NW-IQ.
- ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Raw NAND core changes:
- Drop obsolete dependencies on COMPILE_TEST
- MAINTAINERS: rectify entry for MESON NAND controller bindings
- Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
- marvell: Enable NFC/DEVBUS arbiter
- gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
- mpc5121: Replace NO_IRQ by 0
- lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
- lpc32xx_mlc: Switch to using pm_ptr()
- cadence: Support 64-bit slave dma interface
- rockchip: Describe rk3128-nfc in the bindings
- brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
- winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification"
* tag 'mtd/for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (76 commits)
mtd: rawnand: Drop obsolete dependencies on COMPILE_TEST
mtd: maps: pxa2xx-flash: fix memory leak in probe
mtd: core: Fix refcount error in del_mtd_device()
mtd: spi-nor: add SFDP fixups for Quad Page Program
mtd: spi-nor: issi: is25wp256: Init flash based on SFDP
mtd: spi-nor: winbond: add support for W25Q512NW-IQ
mtd: spi-nor: micron-st: Enable locking for mt25qu256a
mtd: spi-nor: Fix the number of bytes for the dummy cycles
mtd: spi-nor: gigadevice: gd25q256: replace gd25q256_default_init with gd25q256_post_bfpt
mtd: spi-nor: Fix formatting in spi_nor_read_raw() kerneldoc comment
mtd: spi-nor: sysfs: print JEDEC ID for generic flash driver
mtd: spi-nor: add generic flash driver
mtd: spi-nor: fix select_uniform_erase to skip 0 erase size
mtd: spi-nor: move function declaration out of sfdp.h
mtd: spi-nor: remember full JEDEC flash ID
mtd: spi-nor: sysfs: hide manufacturer if it is not set
mtd: spi-nor: hide jedec_id sysfs attribute if not present
mtd: spi-nor: Check for zero erase size in spi_nor_find_best_erase_type()
mtd: rawnand: marvell: Enable NFC/DEVBUS arbiter
mtd: parsers: refer to ARCH_BCMBCA instead of ARCH_BCM4908
...
-----BEGIN PGP SIGNATURE-----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=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEHUIqys8OyG1eHf7fS1VPR6WNFOkFAmOJ59AACgkQS1VPR6WN
FOnzOQf/WLBTNFtPcJoS7cdjlh4fuGySDUKuLifOX+Tmk/ki3XFCZR98cESgb5m+
hCyFDeER/qfdOK9ObT3K1GBS6x7zx8YkskbucjAU0vlIsr2ZHCjNpNiAHrADsKjR
579N0Xwh2ibh7uVJ1xvsPwObdAc8P/tjGHHWF6hGEZzIPYXJVce+qDktkkLfbZ/P
Fik6+y3h68wW/0kDNt/gNmNcb5Z3fjxySs21Np5sy7bUtVVBjHWLo0OpjNadDH9M
m6AkhFA5h9OVl5E4jHBpxc4NvlAa5f6520vESpieseNJiIMWo0W/eSkVsframFew
ILdtXCHjkbS6kgvSpUViobMFsgCjaA==
=Yi2q
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-6.2' into mtd/next
SPI NOR core changes:
* Add support for flash reset using the dt reset-gpios property.
* Update hwcaps.mask to include 8D-8D-8D read and page program ops
when xSPI profile 1.0 table is defined.
* Bypass zero erase size in spi_nor_find_best_erase_type().
* Fix select_uniform_erase to skip 0 erase size
* Add generic flash driver. If a flash is not found in the flash_info
array, fall back to the generic flash driver which is described solely
by the flash's SFDP tables.
* Fix the number of bytes for the dummy cycles in
spi_nor_spimem_check_readop().
* Introduce SPI_NOR_QUAD_PP flag, as PP_1_1_4 is not SFDP discoverable.
SPI NOR manufacturer drivers changes:
* Spansion:
- use PARSE_SFDP for s28hs512t,
- add support for s28hl512t, s28hl01gt, and s28hs01gt.
* Gigadevice: Replace default_init() with post_bfpt() for gd25q256.
* Micron - ST: Enable locking for mt25qu256a.
* Winbond: Add support for W25Q512NW-IQ.
* ISSI: Use PARSE_SFDP and SPI_NOR_QUAD_PP.
Fix merge conflict in the jedec,spi-nor bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmOGGfIACgkQJWrqGEe9
VoSZVQgAmew5RtMegFus/AXflUsGYCvZKfV1LVnxmSoGIKBrJr3yjzh6mFuLyzaP
qt2KljEJ4dblk2M3efosX5YeAkz7A7evm218NHGeKWHMPCDimSE1ptAyBhhMmsVi
cgCgu3LXh369dK9OAm7ZVR4hOdDuK5rpYIcXA4mUh0yqiFxfxsuuNY7QBDVrN+qt
SNmZkTBbCgGRxo7RRanN2ljnSm31p6TyhngUDKG89puMka9gGA9yWLbWFDpwM5SS
L0Tr2ZOHctzz/X/1s2yPcnN6ZPpqsc1wLnGyLOWlhkm7oo7aiT59rlHj9GHbp82h
7lXf7MeWxSNSVr9PMHHUR7XDqlLaOw==
=aOZ+
-----END PGP SIGNATURE-----
Merge tag 'nand/for-6.2' into mtd/next
Raw NAND core changes:
* Drop obsolete dependencies on COMPILE_TEST
* MAINTAINERS: rectify entry for MESON NAND controller bindings
* Drop EXPORT_SYMBOL_GPL for nanddev_erase()
Raw NAND driver changes:
* marvell: Enable NFC/DEVBUS arbiter
* gpmi: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
* mpc5121: Replace NO_IRQ by 0
* lpc32xx_{slc,mlc}:
- Switch to using pm_ptr()
- Switch to using gpiod API
* lpc32xx_mlc: Switch to using pm_ptr()
* cadence: Support 64-bit slave dma interface
* rockchip: Describe rk3128-nfc in the bindings
* brcmnand: Update interrupts description in the bindings
SPI-NAND driver changes:
* winbond:
- Add Winbond W25N02KV flash support
- Fix flash identification
Fix merge conflict with mtd tree regarding the brcm bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
It is actually better to always build such drivers with OF enabled,
so that the test builds are closer to how each driver will actually be
built on its intended target. Building them without OF may not test
much as the compiler will optimize out potentially large parts of the
code. In the worst case, this could even pop false positive warnings.
Dropping COMPILE_TEST here improves the quality of our testing and
avoids wasting time on non-existent issues.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20221124115946.5edb771c@endymion.delvare
Linus Torvalds
Miquel Raynal
Saravana Kannan
Francesco Dolcini
Samuel Holland
Tudor Ambarus
Louis Rannou
Xiangsheng Hou
Pali Rohár
Mario Kicherer
Zeng Heng
Geert Uytterhoeven
Daniel Golle
Arnd Bergmann
Randy Dunlap
JaimeLiao
Uwe Kleine-König
Aviram Dali
Mikhail Zhilkin
Yuan Can
Takahiro Kuwano
Jean Delvare
Zheng Yongjun
Shang XiaoJing