Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, there are lots of minor driver changes across SoC platforms
from NXP, Amlogic, AMD Zynq, Mediatek, Qualcomm, Apple and Samsung.
These usually add support for additional chip variations in existing
drivers, but also add features or bugfixes.
The SCMI firmware subsystem gains a unified raw userspace interface
through debugfs, which can be used for validation purposes.
Newly added drivers include:
- New power management drivers for StarFive JH7110, Allwinner D1 and
Renesas RZ/V2M
- A driver for Qualcomm battery and power supply status
- A SoC device driver for identifying Nuvoton WPCM450 chips
- A regulator coupler driver for Mediatek MT81xxv"
* tag 'soc-drivers-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (165 commits)
power: supply: Introduce Qualcomm PMIC GLINK power supply
soc: apple: rtkit: Do not copy the reg state structure to the stack
soc: sunxi: SUN20I_PPU should depend on PM
memory: renesas-rpc-if: Remove redundant division of dummy
soc: qcom: socinfo: Add IDs for IPQ5332 and its variant
dt-bindings: arm: qcom,ids: Add IDs for IPQ5332 and its variant
dt-bindings: power: qcom,rpmpd: add RPMH_REGULATOR_LEVEL_LOW_SVS_L1
firmware: qcom_scm: Move qcom_scm.h to include/linux/firmware/qcom/
MAINTAINERS: Update qcom CPR maintainer entry
dt-bindings: firmware: document Qualcomm SM8550 SCM
dt-bindings: firmware: qcom,scm: add qcom,scm-sa8775p compatible
soc: qcom: socinfo: Add Soc IDs for IPQ8064 and variants
dt-bindings: arm: qcom,ids: Add Soc IDs for IPQ8064 and variants
soc: qcom: socinfo: Add support for new field in revision 17
soc: qcom: smd-rpm: Add IPQ9574 compatible
soc: qcom: pmic_glink: remove redundant calculation of svid
soc: qcom: stats: Populate all subsystem debugfs files
dt-bindings: soc: qcom,rpmh-rsc: Update to allow for generic nodes
soc: qcom: pmic_glink: add CONFIG_NET/CONFIG_OF dependencies
soc: qcom: pmic_glink: Introduce altmode support
...
RT9467 is a switch-mode single cell Li-Ion/Li-Polymer battery charger
for portable applications.
It integrates a synchronous PWM controller, power MOSFETs,
input current sensing and regulation, high-accuracy voltage regulation,
and charge termination. The charge current is regulated through
integrated sensing resistors.
The RT9467 also features USB On-The-Go (OTG) support. It also integrates
D+/D- pin for USB host/charging port detection.
Co-developed-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the RT9471 3A 1-Cell Li+ battery charger.
The RT9471 is a highly-integrated 3A switch mode battery charger with
low impedance power path to better optimize the charging efficiency.
Co-developed-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: Alina Yu <alina_yu@richtek.com>
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
MediaTek MT6370 is a SubPMIC consisting of a single cell battery charger
with ADC monitoring, RGB LEDs, dual channel flashlight, WLED backlight
driver, display bias voltage supply, one general purpose LDO, and the
USB Type-C & PD controller complies with the latest USB Type-C and PD
standards.
Add support for the MediaTek MT6370 Charger driver. The charger module
of MT6370 supports High-Accuracy Voltage/Current Regulation,
Average Input Current Regulation, Battery Temperature Sensing,
Over-Temperature Protection, DPDM Detection for BC1.2.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: ChiaEn Wu <chiaen_wu@richtek.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This driver supports several chip variants which all share the same I2C
register interface. Since the chip will turn off and become inaccessible
under conditions outside of software control (e.g. upon button press or
input voltage removal), some special handling is needed to delay the
initialization of the IC until it is accessible.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we detect a Samsung SDI battery, we return a static
struct power_supply_battery_info and avoid looking further.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a new battery driver for the uPI uG3105 battery monitor.
Note the uG3105 is not a full-featured autonomous fuel-gauge. Instead it
is expected to be use in combination with some always on microcontroller
reading its coulomb-counter before it can wrap (must be read every 400
seconds!).
Since Linux does not monitor coulomb-counter changes while the device is
off or suspended, the coulomb counter is not used atm.
So far this driver is only used on x86/ACPI (non devicetree) devs
(also note there is no of_match table). Therefor there is no devicetree
bindings documentation for this driver's "upisemi,rsns-microohm" property
since this is not used in actual devicetree files and the dt bindings
maintainers have requested properties with no actual dt users to
_not_ be added to the dt bindings.
The property's name has been chosen so that it should not need to be
changed if/when devicetree enumeration support gets added later, as it
mirrors "maxim,rsns-microohm" from the "maxim,max17042" bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the MAX77976 3.5/5.5A 1-Cell Li+ Battery Charger.
This is a simple implementation enough to be used as a simple battery
charger without OTG and boost.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Immutable branch between regulator and power-supply for for 5.15
This immutable branch introduces the MT6360 charger driver,
which requires a new linear range helper.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds a driver for PCHG (Peripheral CHarGer). PCHG is a
framework managing power supplies for peripheral devices.
This driver creates a sysfs node for each peripheral charge port:
/sys/class/power_supply/peripheral<n>
where <n> is the index of a charge port.
For example, when a stylus is connected to a NFC/WLC port, the node
returns:
/sys/class/power_supply/peripheral0/
capacity=50
charge_type=Standard
scope=Device
status=Charging
type=Battery
Signed-off-by: Daisuke Nojiri <dnojiri@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The "abx500" name on the charging algorithm stems from the ambition
to produce a series of these analog basebands, re-using the same
charging algorithm driver. No ASICs beside AB8500 and AB8505 were
ever produced so this terminology is confusing. Rename the
algorithm file and symbols to reflect the more narrow scope.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The PM2301 was only used in tandem with AB9540, part of U9540,
a platform that was cancelled and never deployed in products.
Delete it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, AC status is also handled via SSAM,
an ACPI shim was present to translate the standard ACPI AC interface to
SSAM requests. The SSAM interface itself, which is modeled closely after
the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support AC
status/information via the aforementioned interface on said Surface
models.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
On newer Microsoft Surface models (specifically 7th-generation, i.e.
Surface Pro 7, Surface Book 3, Surface Laptop 3, and Surface Laptop Go),
battery and AC status/information is no longer handled via standard ACPI
devices, but instead directly via the Surface System Aggregator Module
(SSAM), i.e. the embedded controller on those devices.
While on previous generation models, battery status is also handled via
SSAM, an ACPI shim was present to translate the standard ACPI battery
interface to SSAM requests. The SSAM interface itself, which is modeled
closely after the ACPI interface, has not changed.
This commit introduces a new SSAM client device driver to support
battery status/information via the aforementioned interface on said
Surface models. It is in parts based on the standard ACPI battery
driver.
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds battery gauge driver for Acer Iconia Tab A500 device.
The battery gauge function is provided via the Embedded Controller,
which is found on the Acer A500.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the LTC4162-L Li-Ion battery charger. The driver allows
reading back telemetry and to set some charging options like the input
current limit.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The BQ256XX family of devices are highly integrated buck chargers
for single cell batteries.
Signed-off-by: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add support for the BQ25980, BQ25975 and BQ25960 family of flash
chargers.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Both chips have charger and a fuel gauge.
This adds basic support for displaying the state of the battery and the
input power, settings are not modified. There are some defaults set via
OTP.
Charging also starts after plugging USB.
Known issues of the fuel gauge: There are drivers in the wild which disable
the fuel gauge at shutdown. If a kernel is booted without fuel gauge
support, after such a driver has been used, the fuel gauge will stay off
and decalibrate.
If this driver is used after that, it might display wrong values for charge
level.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This merges the MP2629 battery charge management immutable branch
between MFD, IIO and power-supply due for the v5.8 merge window
into power-supply for-next branch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The mp2629 provides switching-mode battery charge management for
single-cell Li-ion or Li-polymer battery. Driver supports the
access/control input source and battery charging parameters.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ROHM BD99954 is a Battery Management LSI for 1-4 cell Lithium-Ion
secondary battery intended to be used in space-constraint equipment such
as Low profile Notebook PC, Tablets and other applications. BD99954
provides a Dual-source Battery Charger, two port BC1.2 detection and a
Battery Monitor.
Support ROHM BD99954 Charger IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds a driver for the CellWise cw2015 fuel gauge.
The CellWise cw2015 is a shuntless, single-cell Li-Ion fuel gauge used
in the pine64 Pinebook Pro laptop and some Raspberry Pi UPS HATs.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- add HWMON compat layer
- new properties:
- input power limit
- input voltage limit
Drivers:
- qcom-pon: add gen2 support
- new driver for storing reboot move in NVMEM
- new driver for Wilco EC charger configuration
- simplify getting the adapter of a client"
* tag 'for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: nvmem-reboot-mode: add CONFIG_OF dependency
power_supply: wilco_ec: Add charging config driver
power: supply: cros: allow to set input voltage and current limit
power: supply: add input power and voltage limit properties
power: supply: fix semicolon.cocci warnings
power: reset: nvmem-reboot-mode: use NVMEM as reboot mode write interface
dt-bindings: power: reset: add document for NVMEM based reboot-mode
reset: qcom-pon: Add support for gen2 pon
dt-bindings: power: reset: qcom: Add qcom,pm8998-pon compatibility line
power: supply: Add HWMON compatibility layer
power: supply: sbs-manager: simplify getting the adapter of a client
power: supply: rt9455_charger: simplify getting the adapter of a client
power: supply: rt5033_battery: simplify getting the adapter of a client
power: supply: max17042_battery: simplify getting the adapter of a client
power: supply: max17040_battery: simplify getting the adapter of a client
power: supply: max14656_charger_detector: simplify getting the adapter of a client
power: supply: bq25890_charger: simplify getting the adapter of a client
power: supply: bq24257_charger: simplify getting the adapter of a client
power: supply: bq24190_charger: simplify getting the adapter of a client
Add a driver to control the charging algorithm used on Wilco
devices. See Documentation/ABI/testing/sysfs-class-power-wilco
for the userspace interface and other info.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add over-current health state
- Add standard, adaptive and custom charge types
- Add new properties for start/end charge threshold
New Drivers / Hardware:
- UCS1002 Programmable USB Port Power Controller
- Ingenic JZ47xx Battery Fuel Gauge
- AXP20x USB Power: Add AXP813 support
- AT91 poweroff: Add SAM9X60 support
- OLPC battery: Add XO-1.5 and XO-1.75 support
Misc Changes:
- syscon-reboot: support mask property
- AXP288 fuel gauge: Blacklist ACEPC T8/T11. Looks like some vendor
thought it's a good idea to build a desktop system with a fuel
gauge, that slowly "discharges"...
- cpcap-battery: Fix calculation errors
- misc fixes"
* tag 'for-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (54 commits)
power: supply: olpc_battery: force the le/be casts
power: supply: ucs1002: Fix build error without CONFIG_REGULATOR
power: supply: ucs1002: Fix wrong return value checking
power: supply: Add driver for Microchip UCS1002
dt-bindings: power: supply: Add bindings for Microchip UCS1002
power: supply: core: Add POWER_SUPPLY_HEALTH_OVERCURRENT constant
power: supply: core: fix clang -Wunsequenced
power: supply: core: Add missing documentation for CHARGE_CONTROL_* properties
power: supply: core: Add CHARGE_CONTROL_{START_THRESHOLD,END_THRESHOLD} properties
power: supply: core: Add Standard, Adaptive, and Custom charge types
power: supply: axp288_fuel_gauge: Add ACEPC T8 and T11 mini PCs to the blacklist
power: supply: bq27xxx_battery: Notify also about status changes
power: supply: olpc_battery: Have the framework register sysfs files for us
power: supply: olpc_battery: Add OLPC XO 1.75 support
power: supply: olpc_battery: Avoid using platform_info
power: supply: olpc_battery: Use devm_power_supply_register()
power: supply: olpc_battery: Move priv data to a struct
power: supply: olpc_battery: Use DT to get battery version
x86/platform/olpc: Use a correct version when making up a battery node
x86/platform/olpc: Trivial code move in DT fixup
...
There never was a device called LTC3651, it always was just LT3651.
This circumstance makes it pretty difficult to identify what this
driver is meant to control.channges since
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This patch adds basic support for Analog Devices I2C programmable linear
battery charger.
With this driver, some parameters can be read and configured such as:
* trickle charge current level (PRECHARGE_CURRENT)
* trickle charge voltage threshold (VOLTAGE_MIN)
* weak charge threshold (VOLTAGE_AVG)
* constant current (CONSTANT_CHARGE_CURRENT)
* constant charge voltage limit (CONSTANT_CHARGE_VOLTAGE_MAX)
* battery full (CAPACITY_LEVEL)
* input current limit (INPUT_CURRENT_LIMIT)
* charger status (STATUS)
* battery status (CAPACITY_LEVEL)
* termination current (CHARGE_TERM_CURRENT)
Datasheet:
http://www.analog.com/media/en/technical-documentation/data-sheets/ADP5061.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Pull i2c updates from Wolfram Sang:
"This contains two bigger than usual tree-wide changes this time. They
all have proper acks, caused no merge conflicts in linux-next where
they have been for a while. They are namely:
- to-gpiod conversion of the i2c-gpio driver and its users (touching
arch/* and drivers/mfd/*)
- adding a sbs-manager based on I2C core updates to SMBus alerts
(touching drivers/power/*)
Other notable changes:
- i2c_boardinfo can now carry a dev_name to be used when the device
is created. This is because some devices in ACPI world need fixed
names to find the regulators.
- the designware driver got a long discussed overhaul of its PM
handling. img-scb and davinci got PM support, too.
- at24 driver has way better OF support. And it has a new maintainer.
Thanks Bartosz for stepping up!
The rest is regular driver updates and fixes"
* 'i2c/for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (55 commits)
ARM: sa1100: simpad: Correct I2C GPIO offsets
i2c: aspeed: Deassert reset in probe
eeprom: at24: Add OF device ID table
MAINTAINERS: new maintainer for AT24 driver
i2c: nuc900: remove platform_data, too
i2c: thunderx: Remove duplicate NULL check
i2c: taos-evm: Remove duplicate NULL check
i2c: Make i2c_unregister_device() NULL-aware
i2c: xgene-slimpro: Support v2
i2c: mpc: remove useless variable initialization
i2c: omap: Trigger bus recovery in lockup case
i2c: gpio: Add support for named gpios in DT
dt-bindings: i2c: i2c-gpio: Add support for named gpios
i2c: gpio: Local vars in probe
i2c: gpio: Augment all boardfiles to use open drain
i2c: gpio: Enforce open drain through gpiolib
gpio: Make it possible for consumers to enforce open drain
i2c: gpio: Convert to use descriptors
power: supply: sbs-message: fix some code style issues
power: supply: sbs-battery: remove unchecked return var
...
