rk3328_pin_ctrl uses type of RK3288 which has a hack in
rockchip_pinctrl_suspend and rockchip_pinctrl_resume to restore GPIO6-C6
at assume, the hack is not applicable to RK3328 as GPIO6 is not even
exist in it. So use a dedicated pinctrl type to skip this hack.
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Link: https://lore.kernel.org/r/20240606125755.53778-4-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux bits for GPIO3-B1 to GPIO3-B6 pins are not explicitly
specified in RK3328 TRM, however we can get hint from pad name and its
correspinding IOMUX setting for pins in interface descriptions. The
correspinding IOMIX settings for these pins can be found in the same
row next to occurrences of following pad names in RK3328 TRM.
GPIO3-B1: IO_TSPd5m0_CIFdata5m0_GPIO3B1vccio6
GPIO3-B2: IO_TSPd6m0_CIFdata6m0_GPIO3B2vccio6
GPIO3-B3: IO_TSPd7m0_CIFdata7m0_GPIO3B3vccio6
GPIO3-B4: IO_CARDclkm0_GPIO3B4vccio6
GPIO3-B5: IO_CARDrstm0_GPIO3B5vccio6
GPIO3-B6: IO_CARDdetm0_GPIO3B6vccio6
Add pinmux data to rk3328_mux_recalced_data as mux register offset for
these pins does not follow rockchip convention.
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Link: https://lore.kernel.org/r/20240606125755.53778-3-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinmux bits for GPIO2-B0 to GPIO2-B6 actually have 2 bits width,
correct the bank flag for GPIO2-B. The pinmux bits for GPIO2-B7 is
recalculated so it remain unchanged.
The pinmux bits for those pins are not explicitly specified in RK3328
TRM, however we can get hint from pad name and its correspinding IOMUX
setting for pins in interface descriptions. The correspinding IOMIX
settings for GPIO2-B0 to GPIO2-B6 can be found in the same row next to
occurrences of following pad names in RK3328 TRM.
GPIO2-B0: IO_SPIclkm0_GPIO2B0vccio5
GPIO2-B1: IO_SPItxdm0_GPIO2B1vccio5
GPIO2-B2: IO_SPIrxdm0_GPIO2B2vccio5
GPIO2-B3: IO_SPIcsn0m0_GPIO2B3vccio5
GPIO2-B4: IO_SPIcsn1m0_FLASHvol_sel_GPIO2B4vccio5
GPIO2-B5: IO_ I2C2sda_TSADCshut_GPIO2B5vccio5
GPIO2-B6: IO_ I2C2scl_GPIO2B6vccio5
This fix has been tested on NanoPi R2S for fixing confliting pinmux bits
between GPIO2-B7 with GPIO2-B5.
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Fixes: 3818e4a767 ("pinctrl: rockchip: Add rk3328 pinctrl support")
Link: https://lore.kernel.org/r/20240606125755.53778-2-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In create_pinctrl(), pinctrl_maps_mutex is acquired before calling
add_setting(). If add_setting() returns -EPROBE_DEFER, create_pinctrl()
calls pinctrl_free(). However, pinctrl_free() attempts to acquire
pinctrl_maps_mutex, which is already held by create_pinctrl(), leading to
a potential deadlock.
This patch resolves the issue by releasing pinctrl_maps_mutex before
calling pinctrl_free(), preventing the deadlock.
This bug was discovered and resolved using Coverity Static Analysis
Security Testing (SAST) by Synopsys, Inc.
Fixes: 42fed7ba44 ("pinctrl: move subsystem mutex to pinctrl_dev struct")
Suggested-by: Maximilian Heyne <mheyne@amazon.de>
Signed-off-by: Hagar Hemdan <hagarhem@amazon.com>
Link: https://lore.kernel.org/r/20240604085838.3344-1-hagarhem@amazon.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing support for LP8764 PMIC in the probe().
Issue detected with v6.10-rc1 (and reproduced with 6.10-rc2) using a TI
J7200 EVM board.
tps6594-pinctrl tps6594-pinctrl.8.auto: error -EINVAL:
Couldn't register gpio_regmap driver
tps6594-pinctrl tps6594-pinctrl.8.auto: probe with driver tps6594-pinctrl
failed with error -22
Fixes: 2088297159 (pinctrl: pinctrl-tps6594: Add TPS65224 PMIC pinctrl and GPIO)
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://lore.kernel.org/r/20240603082110.2104977-1-thomas.richard@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPMI GPIO driver assumes that the parent device is an SPMI device
and accesses random data when backcasting the parent struct device
pointer for non-SPMI devices.
Fortunately this does not seem to cause any issues currently when the
parent device is an I2C client like the PM8008, but this could change if
the structures are reorganised (e.g. using structure randomisation).
Notably the interrupt implementation is also broken for non-SPMI devices.
Also note that the two GPIO pins on PM8008 are used for interrupts and
reset so their practical use should be limited.
Drop the broken GPIO support for PM8008 for now.
Fixes: ea119e5a48 ("pinctrl: qcom-pmic-gpio: Add support for pm8008")
Cc: stable@vger.kernel.org # 5.13
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240529162958.18081-9-johan+linaro@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull MFD updates from Lee Jones:
"New Device Support:
- Add support for X-Powers AXP717 PMIC to AXP22X
- Add support for Rockchip RK816 PMIC to RK8XX
- Add support for TI TPS65224 PMIC to TPS6594
New Functionality:
- Add Power Off functionality to Rohm BD71828
- Allow I2C SMBus access in Renesas RSMU
Fix-ups:
- Device Tree binding adaptions/conversions/creation
- Shift Intel support over to MSI interrupts
- Generify adding platform data away from being ACPI specific
- Use device core supplied attribute to register sysfs entries
- Replace hand-rolled functionality with generic APIs
- Utilise centrally provided helpers and macros
- Clean-up error handling
- Remove superfluous/duplicated/unused sections
- Trivial; spelling, whitespace, coding-style adaptions
- More Maple Tree conversions"
* tag 'mfd-next-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (44 commits)
dt-bindings: mfd: Use full path to other schemas
mfd: rsmu: support I2C SMBus access
dt-bindings: mfd: Convert lp873x.txt to json-schema
dt-bindings: mfd: aspeed: Drop 'oneOf' for pinctrl node
dt-bindings: mfd: allwinner,sun6i-a31-prcm: Use hyphens in node names
mfd: ssbi: Remove unused field 'slave' from 'struct ssbi'
mfd: kempld: Remove custom DMI matching code
mfd: cs42l43: Update patching revision check
dt-bindings: mfd: qcom: pm8xxx: Add pm8901 compatible
mfd: timberdale: Remove redundant assignment to variable err
dt-bindings: mfd: qcom,spmi-pmic: Add pbs to SPMI device types
dt-bindings: mfd: syscon: Add ti,am62p-cpsw-mac-efuse compatible
dt-bindings: mfd: qcom,tcsr: Add compatible for SDX75
mfd: axp20x: Convert to use Maple Tree register cache
mfd: bd71828: Remove commented code lines
mfd: intel-m10-bmc: Change staging size to a variable
dt-bindings: mfd: Add ROHM BD71879
mfd: Tidy Kconfig dependency's parentheses
mfd: ocelot-spi: Use spi_sync_transfer()
dt-bindings: mfd: syscon: Add missing simple syscon compatibles
...
Pull pin control updates from Linus Walleij:
"Core changes:
- Use DEFINE_SHOW_STORE_ATTRIBUTE() in debugfs entries
New drivers:
- Qualcomm PMIH0108, PMD8028, PMXR2230 and PM6450 pin control support
Improvements:
- Serious cleanup of the recently merged aw9523 driver
- Fix PIN_CONFIG_BIAS_DISABLE handling in pinctrl-single
- A slew of device tree binding cleanups
- Support a bus clock in the Samsung driver"
* tag 'pinctrl-v6.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (48 commits)
pinctrl: bcm2835: Make pin freeing behavior configurable
dt-bindings: pinctrl: qcom,pmic-gpio: Fix "comptaible" typo for PMIH0108
pinctrl: qcom: pinctrl-sm7150: Fix sdc1 and ufs special pins regs
dt-bindings: pinctrl: mediatek: mt7622: add "antsel" function
dt-bindings: pinctrl: mediatek: mt7622: fix array properties
pinctrl: samsung: drop redundant drvdata assignment
pinctrl: samsung: support a bus clock
dt-bindings: pinctrl: samsung: google,gs101-pinctrl needs a clock
pinctrl: renesas: rzg2l: Limit 2.5V power supply to Ethernet interfaces
pinctrl: renesas: r8a779h0: Add INTC-EX pins, groups, and function
pinctrl: renesas: r8a779h0: Fix IRQ suffixes
pinctrl: renesas: rzg2l: Remove extra space in function parameter
dt-bindings: pinctrl: qcom,pmic-mpp: add support for PM8901
pinctrl: pinconf-generic: print hex value
pinctrl: realtek: fix module autoloading
pinctrl: qcom: sm7150: fix module autoloading
pinctrl: loongson2: fix module autoloading
pinctrl: mediatek: fix module autoloading
pinctrl: freescale: imx8ulp: fix module autoloading
dt-bindings: pinctrl: qcom,pmic-gpio: Allow gpio-hog nodes
...
Pull gpio updates from Bartosz Golaszewski
"This was a quiet release cycle for the GPIO tree and so this
pull-request is relatively small.
We have one new driver, some minor improvements to the GPIO core code
and across several drivers, some DT and documentation updates but in
general nothing stands out or is controversial. All changes have spent
time in next with no reported issues (or ones that were quickly
fixed).
GPIO core:
- remove more unused legacy interfaces (after converting the last
remaining users to better alternatives)
- update kerneldocs
- improve error handling and log messages in GPIO ACPI code
- remove dead code (always true checks) from GPIOLIB
New drivers:
- add a driver for Intel Granite Rapids-D vGPIO
Driver improvements:
- use -ENOTSUPP consistently in gpio-regmap and gpio-pcie-idio-24
- provide an ID table for gpio-cros-ec to avoid a driver name
fallback check
- add support for gpio-ranges for GPIO drivers supporting multiple
GPIO banks
- switch to using dynamic GPIO base in gpio-brcmstb
- fix irq handling in gpio-npcm-sgpio
- switch to memory mapped IO accessors in gpio-sch
DT bindings:
- add support for gpio-ranges to gpio-brcmstb
- add support for a new model and the gpio-line-names property to
gpio-mpfs
Documentation:
- replace leading tabs with spaces in code blocks
- fix typos"
* tag 'gpio-updates-for-v6.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (30 commits)
gpio: nuvoton: Fix sgpio irq handle error
gpiolib: Discourage to use formatting strings in line names
gpio: brcmstb: add support for gpio-ranges
gpio: of: support gpio-ranges for multiple gpiochip devices
dt-bindings: gpio: brcmstb: add gpio-ranges
gpio: Add Intel Granite Rapids-D vGPIO driver
gpio: brcmstb: Use dynamic GPIO base numbers
gpiolib: acpi: Set label for IRQ only lines
gpiolib: acpi: Add fwnode name to the GPIO interrupt label
gpiolib: Get rid of never false gpio_is_valid() calls
gpiolib: acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
gpiolib: acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
gpiolib: acpi: Simplify error handling in __acpi_find_gpio()
gpiolib: acpi: Extract __acpi_find_gpio() helper
gpio: sch: Utilise temporary variable for struct device
gpio: sch: Switch to memory mapped IO accessors
gpio: regmap: Use -ENOTSUPP consistently
gpio: pcie-idio-24: Use -ENOTSUPP consistently
Documentation: gpio: Replace leading TABs by spaces in code blocks
gpiolib: acpi: Check for errors first in acpi_find_gpio()
...
Pull SoC driver updates from Arnd Bergmann:
"As usual, these are updates for drivers that are specific to certain
SoCs or firmware running on them.
Notable updates include
- The new STMicroelectronics STM32 "firewall" bus driver that is used
to provide a barrier between different parts of an SoC
- Lots of updates for the Qualcomm platform drivers, in particular
SCM, which gets a rewrite of its initialization code
- Firmware driver updates for Arm FF-A notification interrupts and
indirect messaging, SCMI firmware support for pin control and
vendor specific interfaces, and TEE firmware interface changes
across multiple TEE drivers
- A larger cleanup of the Mediatek CMDQ driver and some related bits
- Kconfig changes for riscv drivers to prepare for adding Kanaan k230
support
- Multiple minor updates for the TI sysc bus driver, memory
controllers, hisilicon hccs and more"
* tag 'soc-drivers-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (103 commits)
firmware: qcom: uefisecapp: Allow on sc8180x Primus and Flex 5G
soc: qcom: pmic_glink: Make client-lock non-sleeping
dt-bindings: soc: qcom,wcnss: fix bluetooth address example
soc/tegra: pmc: Add EQOS wake event for Tegra194 and Tegra234
bus: stm32_firewall: fix off by one in stm32_firewall_get_firewall()
bus: etzpc: introduce ETZPC firewall controller driver
firmware: arm_ffa: Avoid queuing work when running on the worker queue
bus: ti-sysc: Drop legacy idle quirk handling
bus: ti-sysc: Drop legacy quirk handling for smartreflex
bus: ti-sysc: Drop legacy quirk handling for uarts
bus: ti-sysc: Add a description and copyrights
bus: ti-sysc: Move check for no-reset-on-init
soc: hisilicon: kunpeng_hccs: replace MAILBOX dependency with PCC
soc: hisilicon: kunpeng_hccs: Add the check for obtaining complete port attribute
firmware: arm_ffa: Fix memory corruption in ffa_msg_send2()
bus: rifsc: introduce RIFSC firewall controller driver
of: property: fw_devlink: Add support for "access-controller"
soc: mediatek: mtk-socinfo: Correct the marketing name for MT8188GV
soc: mediatek: mtk-socinfo: Add entry for MT8395AV/ZA Genio 1200
soc: mediatek: mtk-mutex: Add support for MT8188 VPPSYS
...
RISC-V SoC Kconfig Updates for v6.10
A few different bits of SoC-related Kconfig work. The first part of
this is shared with the DT updates - the modification of all SOC_CANAAN
users to SOC_CANAAN_K210 to split the existing m-mode nommu k210 away
from the k230 that is able to be used in a "common" kernel.
The other thing here is the removal of most of the SOC_VENDOR options,
with their ARCH_VENDOR equivalents that've been waiting in the wings for
1 year+ now made visible. Due a lapse on my part when originally adding
the ARCH_VENDOR stuff, the Microchip transition isn't complete - the
_POLARFIRE was a mistake to keep as there's gonna be non-PolarFire
RISC-V stuff from Microchip soonTM.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-config-for-v6.10' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: config: enable ARCH_CANAAN in defconfig
RISC-V: drop SOC_VIRT for ARCH_VIRT
RISC-V: drop SOC_SIFIVE for ARCH_SIFIVE
RISC-V: drop SOC_MICROCHIP_POLARFIRE for ARCH_MICROCHIP
RISC-V: Drop unused SOC_CANAAN
reset: k210: Deprecate SOC_CANAAN and use SOC_CANAAN_K210
pinctrl: k210: Deprecate SOC_CANAAN and use SOC_CANAAN_K210
clk: k210: Deprecate SOC_CANAAN and use SOC_CANAAN_K210
soc: canaan: Deprecate SOC_CANAAN and use SOC_CANAAN_K210 for K210
riscv: Kconfig.socs: Split ARCH_CANAAN and SOC_CANAAN_K210
Link: https://lore.kernel.org/r/20240503-mardi-underling-3d81a9f97329@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
intel-gpio for v6.10-1
* New driver for vGPIO controller on Intel Granite Rapids-D
* Update ACPI GPIO library to unify the IRQ code path
* Better GPIO IRQ line labeling for ACPI
* Switched Intel SCH driver to use "mapped" I/O accessors
The following is an automated git shortlog grouped by driver:
Add Intel Granite Rapids-D vGPIO driver:
- Add Intel Granite Rapids-D vGPIO driver
crystalcove:
- Use -ENOTSUPP consistently
gpiolib:
- acpi: Set label for IRQ only lines
- acpi: Add fwnode name to the GPIO interrupt label
- acpi: Pass con_id instead of property into acpi_dev_gpio_irq_get_by()
- acpi: Move acpi_can_fallback_to_crs() out of __acpi_find_gpio()
- acpi: Simplify error handling in __acpi_find_gpio()
- acpi: Extract __acpi_find_gpio() helper
- acpi: Check for errors first in acpi_find_gpio()
- acpi: Remove never true check in acpi_get_gpiod_by_index()
sch:
- Utilise temporary variable for struct device
- Switch to memory mapped IO accessors
wcove:
- Use -ENOTSUPP consistently
Samsung pinctrl drivers changes for v6.10
1. Add support for toggling bus clock (PCLK) for any pin controller
register accesses. This looks needed on newer Samsung chips, like
Google GS101 and probably Exynos850.
2. Drop old, deprecated in v6.1 bindings header with register constants.
The constants were moved to DTS headers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Until now after a bcm2835 pin was freed its pinmux was set to GPIO_IN.
So in case it was configured as GPIO_OUT before the configured output
level also get lost. As long as GPIO sysfs was used this wasn't
actually a problem because the pins and their possible output level
were kept by sysfs.
Since more and more Raspberry Pi users start using libgpiod they are
confused about this behavior. So make the pin freeing behavior of
GPIO_OUT configurable via module parameter. In case
pinctrl-bcm2835.persist_gpio_outputs is set to 1, the output level is
kept.
This patch based on the downstream work of Phil Elwell.
Link: https://github.com/raspberrypi/linux/pull/6117
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Message-ID: <20240503062745.11298-1-wahrenst@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull pin control fixes from Linus Walleij:
- Fix a double-free in the pinctrl_enable() errorpath
- Fix a refcount leak in pinctrl_dt_to_map()
- Fix selecting the GPIO pin control state and the UART3 pin config
group in the Intel Baytrail driver
- Fix readback of schmitt trigger status in the Mediatek Paris driver,
along with some semantic pin config issues in this driver
- Fix a pin suffix typo in the Meson A1 driver
- Fix an erroneous register offset in he Aspeed G6 driver
- Fix an inconsistent lock state and the interrupt type on resume in
the Renesas RZG2L driver
- Fix some minor confusion in the Renesas DT bindings
* tag 'pinctrl-v6.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: renesas: rzg2l: Configure the interrupt type on resume
pinctrl: devicetree: fix refcount leak in pinctrl_dt_to_map()
pinctrl: baytrail: Add pinconf group for uart3
pinctrl: baytrail: Fix selecting gpio pinctrl state
pinctrl: mediatek: paris: Rework support for PIN_CONFIG_{INPUT,OUTPUT}_ENABLE
pinctrl: mediatek: paris: Fix PIN_CONFIG_INPUT_SCHMITT_ENABLE readback
pinctrl: core: delete incorrect free in pinctrl_enable()
pinctrl/meson: fix typo in PDM's pin name
pinctrl: pinctrl-aspeed-g6: Fix register offset for pinconf of GPIOR-T
pinctrl: renesas: rzg2l: Execute atomically the interrupt configuration
dt-bindings: pinctrl: renesas,rzg2l-pinctrl: Allow 'input' and 'output-enable' properties
Arm SCMI updates for v6.10
1. Basic support for SCMI v3.2 pincontrol protocol
SCMI v3.2 introduces pincontrol protocol which is intended for
controlling pins and their configuration. The pin control protocol
provides commands to:
- List the pins, groups of pins, available functions, and their
association with each other.
- Set the parameter configuration and multiplexing of the pins or
groups of pins
- Optionally request exclusive access to a pin or group of pins.
- Optionally configure the permissions of an agent to access a pin
or group of pins.
These changes adds basic support for the same in the SCMI core layer
and an implementation of the generic scmi-pinctrl driver with associated
DT bindings.
2. Framework support for multiple vendors custom protocols
With the fixed space for vendor protocols, the possibility of having
multiple vendors implementing distinct SCMI vendor protocols with
the same overlapping protocol number is very high and with the need
to support them all in a single kernel image or a module is also high.
In order to implement the same we assume:
- vendor protocols has to be tagged at build time with a vendor_id
- vendor protocols could also optionally be tagged at build time with
sub_vendor_id and implementation version
At the initialisation all the built vendor protocols are registered
with the SCMI core using a key derived from the above tags
3. Logging and tracing improvements
This includes using dev_err_probe() to bail out from probe, adding
message dump traces for bad and unexpected replies and widening of
the tag buffer in trace_scmi_dump_msg to allow diverse tag names
4. Miscellaneous updates or improvements
This includes adding the accessor function get_max_msg_size() used
in pinctl protocol, updation of dt-bindings examples for protocol@13
to promote new bindings and simplification of scmi_devm_notifier_unregister
* tag 'scmi-updates-6.10' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
pinctrl: Implementation of the generic scmi-pinctrl driver
firmware: arm_scmi: Add basic support for SCMI v3.2 pincontrol protocol
dt-bindings: firmware: Support SCMI pinctrl protocol
firmware: arm_scmi: Introduce get_max_msg_size() helper/accessor
firmware: arm_scmi: Add support for multiple vendors custom protocols
dt-bindings: firmware: arm,scmi: Update examples for protocol@13
firmware: arm_scmi: Avoid non-constant printk format strings
firmware: arm_scmi: Use dev_err_probe to bail out
firmware: arm_scmi: Simplify scmi_devm_notifier_unregister
firmware: arm_scmi: Add message dump traces for bad and unexpected replies
firmware: arm_scmi: Add helper to trace bad messages
include: trace: Widen the tag buffer in trace_scmi_dump_msg
firmware: arm_scmi: Log the perf domain names in the error paths
Link: https://lore.kernel.org/r/20240426105031.1526987-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On some Samsung-based SoCs there are separate bus clocks / gates each
for each pinctrl instance. To be able to access each pinctrl instance's
registers, this bus clock needs to be running, otherwise register
access will hang. Google Tensor gs101 is one example for such an
implementation.
Update the driver to handle this optional bus clock:
* handle an optional bus clock from DT
* prepare it during driver probe
* enclose all relevant register accesses with a clock enable & disable
Signed-off-by: André Draszik <andre.draszik@linaro.org>
Link: https://lore.kernel.org/r/20240426-samsung-pinctrl-busclock-v3-2-adb8664b8a7e@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
intel-pinctrl for v6.9-1
* Correct GPIO selection and add UART3 pins for Intel Bay Trail
The following is an automated git shortlog grouped by driver:
baytrail:
- Add pinconf group for uart3
- Fix selecting gpio pinctrl state
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The RZ/G3S SoC supports configurable supply voltages for several of its
I/O interfaces. All of these interfaces support both 1.8V and 3.3V
supplies, but only the Ethernet and XSPI interfaces support a 2.5V
supply.
Voltage selection for the XSPI interface is not yet supported, so this
leaves only the Ethernet interfaces currently supporting selection of a
2.5V supply. So we need to return an error if there is an attempt to
select a 2.5V supply for any non-Ethernet interface.
Fixes: 51996952b8 ("pinctrl: renesas: rzg2l: Add support to select power source for Ethernet pins")
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240417114132.6605-1-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Commit dce0919c83 ("irqchip/renesas-rzg2l: Do not set TIEN and TINT
source at the same time") removed the setup of TINT from
rzg2l_irqc_irq_enable(). To address the spurious interrupt issue the
setup of TINT has been moved in rzg2l_tint_set_edge() through
rzg2l_disable_tint_and_set_tint_source(). With this, the interrupts are
not properly re-configured after a suspend-to-RAM cycle. To address
this issue and avoid spurious interrupts while resumming set the
interrupt type before enabling it.
Fixes: dce0919c83 ("irqchip/renesas-rzg2l: Do not set TIEN and TINT source at the same time")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240419063822.3467424-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
pinctrl: renesas: Fixes for v6.9
- Fix a dtbs_check warning on RZ/G3S,
- Fix a lockdep warning on RZ/G2L.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table. Pin controllers are
considered core components, so usually they are built-in, however these
can be built and used as modules on some generic kernel.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-ID: <20240411064614.7409-5-krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table. Pin controllers are
considered core components, so usually they are built-in, however these
can be built and used as modules on some generic kernel.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-ID: <20240411064614.7409-3-krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table. Pin controllers are
considered core components, so usually they are built-in, however these
can be built and used as modules on some generic kernel.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <20240411064614.7409-2-krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add MODULE_DEVICE_TABLE(), so the module could be properly autoloaded
based on the alias from of_device_id table. Pin controllers are
considered core components, so usually they are built-in, however these
can be built and used as modules on some generic kernel.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Message-ID: <20240411064614.7409-1-krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_S0_SC57 / GPIO_S0_SC61 can be muxed to PCU_UART_TXD / PCU_UART_RXD,
add a pinconf group for this.
On Bay Trail board schematics using these pins as UART these are
called UART3_TXD / UART3_RXD, name the pinconf group "uart3_grp"
to be consistent with the schematics.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For all the "score" pin-groups all the intel_pingroup-s to select
the non GPIO function are re-used for byt_score_gpio_groups[].
But this is incorrect since a pin-group includes the mode setting,
which for the non GPIO functions generally is 1, where as to select
the GPIO function mode must be set to 0.
So the GPIO function needs separate intel_pingroup-s with their own mode
value of 0.
Add a new PIN_GROUP_GPIO macro which adds a foo_gpio entry to each
pin-group defined this way and update byt_score_gpio_groups[] to point
to the new foo_gpio entries.
The "sus" usb_oc_grp usb_ulpi_grp and pcu_spi_grp pin-groups are special
because these have a non 0 mode value to select the GPIO functions and
these already have matching foo_gpio pin-groups, leave these are unchanged.
The pmu_clk "sus" groups added in commit 2f46d7f7e9 ("pinctrl: baytrail:
Add pinconf group + function for the pmu_clk") do need to use the new
PIN_GROUP_GPIO macro.
Fixes: 2f46d7f7e9 ("pinctrl: baytrail: Add pinconf group + function for the pmu_clk")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The pinctrl-single driver handles pin_config_set by looking up the
requested setting in a DT-defined lookup table, which defines what bits
correspond to each setting. There is no way to add
PIN_CONFIG_BIAS_DISABLE entries to the table, since there is instead
code to disable the bias by applying the disable values of both the
pullup and pulldown entries in the table.
However, this code is inside the table-lookup loop, so it would only
execute if there is an entry for PIN_CONFIG_BIAS_DISABLE in the table,
which can never exist, so this code never runs.
This commit lifts the offending code out of the loop, so it just
executes directly whenever PIN_CONFIG_BIAS_DISABLE is requested,
skippipng the table lookup loop.
This also introduces a new `param` variable to make the code slightly
more readable.
This bug seems to have existed when this code was first merged in commit
9dddb4df90 ("pinctrl: single: support generic pinconf"). Earlier
versions of this patch did have an entry for PIN_CONFIG_BIAS_DISABLE in
the lookup table, but that was removed, which is probably how this bug
was introduced.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Reviewed-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Message-ID: <20240319110633.230329-1-matthijs@stdin.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
