In order to let drivers have more dynamic U-APSD support,
move the enablement flag to the virtual interface driver
flags. This lets drivers not only set it up differently
for different interfaces, but also enable/disable on the
fly if needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The power level might have been set, but as the interface was idle
it might not have taken effect yet. Ask the driver to check the
power level when starting up an AP so that in this case the correct
power level is used in case the device/driver can only set it when
the interface is actually active.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is curently possible to run a VM with architected timers support
without creating an in-kernel VGIC, which will result in interrupts from
the virtual timer going nowhere.
To address this issue, move the architected timers initialization to the
time when we run a VCPU for the first time, and then only initialize
(and enable) the architected timers if we have a properly created and
initialized in-kernel VGIC.
When injecting interrupts from the virtual timer to the vgic, the
current setup should ensure that this never calls an on-demand init of
the VGIC, which is the only call path that could return an error from
kvm_vgic_inject_irq(), so capture the return value and raise a warning
if there's an error there.
We also change the kvm_timer_init() function from returning an int to be
a void function, since the function always succeeds.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Userspace assumes that it can wire up IRQ injections after having
created all VCPUs and after having created the VGIC, but potentially
before starting the first VCPU. This can currently lead to lost IRQs
because the state of that IRQ injection is not stored anywhere and we
don't return an error to userspace.
We haven't seen this problem manifest itself yet, presumably because
guests reset the devices on boot, but this could cause issues with
migration and other non-standard startup configurations.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
LFP brighness control from the VBT block 43 indicates which
controller is used for brightness.
LFP1 brightness control method:
Bit 7-4 = This field controller number of the brightnes controller.
0 = Controller 0
1 = Controller 1
2 = Controller 2
3 = Controller 3
Others = Reserved
Bits 3-0 = This field specifies the brightness control pin to be used on the
platform.
0 = PMIC pin is used for brightness control
1 = LPSS PWM is used for brightness control
2 = Display DDI is used for brightness control
3 = CABC method to control brightness
Others = Reserved
Adding the above fields in dev_priv->vbt and corresponding changes in
parse_backlight()
v2: Jani's review comments addressed
- Move PWM definitions to intel_bios.h
- Moving vbt_version to intel_vbt_data
- Rename brightness to bl_ctrl_data
- Logging just control_pin instead of string
- Avoid adding vbt_version in dev_priv
- Since only DDI option is available as of now, let control pin DDI
affect dev_priv->vbt.backlight.present
v3: Jani's review comments addressed
- Drop control_pin
- Use bdb->version
- set controller to 0 instead of using control pin define
- check controller bounds
- remove superfluous changes in intel_parse_bios
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Execlist support in the i915 driver is now considered good enough for the
feature to be enabled by default on Gen8 and later and routinely tested.
Adjusted i915 parameters structure initialization to reflect this and updated
the comment in intel_sanitize_enable_execlists().
There's still work to do before we can let the wider massive onto it,
but there's still time left before the 3.20 cutoff.
v2: Update the MODULE_PARM_DESC too.
Issue: VIZ-2020
Signed-off-by: Thomas Daniel <thomas.daniel@intel.com>
[danvet: Add note that there's still some work left to do.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The pipe wm parameters is not correctly updated with sprite parameters
because it copies them for each plane from plane_list to the sprite
offset in pipe wm parameters. Since plane_list also contains primary and
cursor planes, we end up updating wrong params for sprites.
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A short section describing background, implementation and intended usage.
v2:
* Align section name between template and DOC comment. (Michel Thierry)
For: VIZ-4544
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Things like reliable GGTT mappings and mirrored 2d-on-3d display will need
to map objects into the same address space multiple times.
Added a GGTT view concept and linked it with the VMA to distinguish between
multiple instances per address space.
New objects and GEM functions which do not take this new view as a parameter
assume the default of zero (I915_GGTT_VIEW_NORMAL) which preserves the
previous behaviour.
This now means that objects can have multiple VMA entries so the code which
assumed there will only be one also had to be modified.
Alternative GGTT views are supposed to borrow DMA addresses from obj->pages
which is DMA mapped on first VMA instantiation and unmapped on the last one
going away.
v2:
* Removed per view special casing in i915_gem_ggtt_prepare /
finish_object in favour of creating and destroying DMA mappings
on first VMA instantiation and last VMA destruction. (Daniel Vetter)
* Simplified i915_vma_unbind which does not need to count the GGTT views.
(Daniel Vetter)
* Also moved obj->map_and_fenceable reset under the same check.
* Checkpatch cleanups.
v3:
* Only retire objects once the last VMA is unbound.
v4:
* Keep scatter-gather table for alternative views persistent for the
lifetime of the VMA.
* Propagate binding errors to callers and handle appropriately.
v5:
* Explicitly look for normal GGTT view in i915_gem_obj_bound to align
usage in i915_gem_object_ggtt_unpin. (Michel Thierry)
* Change to single if statement in i915_gem_obj_to_ggtt. (Michel Thierry)
* Removed stray semi-colon in i915_gem_object_set_cache_level.
For: VIZ-4544
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
[danvet: Drop hunk from i915_gem_shrink since it's just prettification
but upsets a __must_check warning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes random memory corruption triggered when all three of the
following are true:
* scsi-mq enabled
* T10 Protection Information (DIF) enabled
* SCSI host with sg_tablesize > SCSI_MAX_SG_SEGMENTS (128)
The symptoms of this bug are unpredictable memory corruption, BUG()s,
oopses, lockups, etc., any of which may appear to be completely
unrelated to the root cause.
Cc: <stable@vger.kernel.org> # 3.17.x, 3.18.x
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Reviewed-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch adds codec ID (0x80862809) and module alias for Skylake
display codec.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This code tends to use unsigned variables by default and it causes
signedness bugs when we use negative variables for error handling.
The "i" and "j" variables are used to iterated over small positive
values and so they should be type "int". The "len" variable doesn't
*need* to be signed but it should be signed to make the code easier to
read and audit.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
According to updated BSpec, Render/Common/media Wells register range changed.
Updating the same to match the spec and avoid extra forcewake for none
forcewake range.
v2: Update media forcewake range (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From now on for both DSI Ports A & C, the seq_port value has been
set to 0. seq_port value is parsed from Sequence block#53 of VBT.
So, for packets that needs to be read/write for DSI single link on
Port A and Port C will now be based on the DVO port from VBT block 2,
instead of seq_port.
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Faster feedback to errors is always better. This is inspired by the
addition to WARN_ONs to mask/enable helpers for registers to make sure
callers have the arguments ordered correctly: Pretty much always the
arguments are static.
We use WARN_ON(1) a lot in default switch statements though where we
should always handle all cases. So add a new macro specifically for
that.
The idea to use __builtin_constant_p is from Chris Wilson.
v2: Use the ({}) gcc-ism to avoid the static inline, suggested by
Dave. My first attempt used __cond as the temp var, which is the same
used by BUILD_BUG_ON, but with inverted sense. Hilarity ensued, so
sprinkle i915 into the name.
Also use a temporary variable to only evaluate the condition once,
suggested by Damien.
v3: It's crazy but apparently 32bit gcc can't compile out the
BUILD_BUG_ON in a lot of cases and just falls over. I have no idea
why, but until clue grows just disable this nifty idea on 32bit
builds. Reported by 0-day builder.
v4: Got it all wrong, apparently its the gcc version. We need 4.9+.
Now reported by Imre.
v5: Chris suggested to add the case to MISSING_CASE for speedier
debug.
v6: Even some gcc 4.9 versions don't see through the maze, so give up
for now. Keep the skeleton and MISSING_CASE stuff though.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
We consistently use the _irq_handler postfix for functions called in
hardirq context. Especially when it's a non-static function hardirq is
a crazy enough calling context to warrant this level of ocd. So rename
it.
Cc: Thomas Daniel <thomas.daniel@intel.com>
Reviewed-by: Thomas Daniel <thomas.daniel@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
When compiling in module some symbol aren't missing,
export them correctly.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows the sdplite/Zebu images to run on OSCI simulation platform
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: <stable@vger.kernel.org> #3.10, 3.12, 3.14, 3.16
Pull security layer updates from James Morris:
"In terms of changes, there's general maintenance to the Smack,
SELinux, and integrity code.
The IMA code adds a new kconfig option, IMA_APPRAISE_SIGNED_INIT,
which allows IMA appraisal to require signatures. Support for reading
keys from rootfs before init is call is also added"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (23 commits)
selinux: Remove security_ops extern
security: smack: fix out-of-bounds access in smk_parse_smack()
VFS: refactor vfs_read()
ima: require signature based appraisal
integrity: provide a hook to load keys when rootfs is ready
ima: load x509 certificate from the kernel
integrity: provide a function to load x509 certificate from the kernel
integrity: define a new function integrity_read_file()
Security: smack: replace kzalloc with kmem_cache for inode_smack
Smack: Lock mode for the floor and hat labels
ima: added support for new kernel cmdline parameter ima_template_fmt
ima: allocate field pointers array on demand in template_desc_init_fields()
ima: don't allocate a copy of template_fmt in template_desc_init_fields()
ima: display template format in meas. list if template name length is zero
ima: added error messages to template-related functions
ima: use atomic bit operations to protect policy update interface
ima: ignore empty and with whitespaces policy lines
ima: no need to allocate entry for comment
ima: report policy load status
ima: use path names cache
...
Newer versions of OPAL will provide this, so let's expose it to user
space so tools like perf can use it to properly decode samples in
firmware space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Winkle is a deep idle state supported in power8 chips. A core enters
winkle when all the threads of the core enter winkle. In this state
power supply to the entire chiplet i.e core, private L2 and private L3
is turned off. As a result it gives higher powersavings compared to
sleep.
But entering winkle results in a total hypervisor state loss. Hence the
hypervisor context has to be preserved before entering winkle and
restored upon wake up.
Power-on Reset Engine (PORE) is a dedicated engine which is responsible
for powering on the chiplet during wake up. It can be programmed to
restore the register contests of a few specific registers. This patch
uses PORE to restore register state wherever possible and uses stack to
save and restore rest of the necessary registers.
With hypervisor state restore things fall under three categories-
per-core state, per-subcore state and per-thread state. To manage this,
extend the infrastructure introduced for sleep. Mainly we add a paca
variable subcore_sibling_mask. Using this and the core_idle_state we can
distingush first thread in core and subcore.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Deep idle states like sleep and winkle are per core idle states. A core
enters these states only when all the threads enter either the
particular idle state or a deeper one. There are tasks like fastsleep
hardware bug workaround and hypervisor core state save which have to be
done only by the last thread of the core entering deep idle state and
similarly tasks like timebase resync, hypervisor core register restore
that have to be done only by the first thread waking up from these
state.
The current idle state management does not have a way to distinguish the
first/last thread of the core waking/entering idle states. Tasks like
timebase resync are done for all the threads. This is not only is
suboptimal, but can cause functionality issues when subcores and kvm is
involved.
This patch adds the necessary infrastructure to track idle states of
threads in a per-core structure. It uses this info to perform tasks like
fastsleep workaround and timebase resync only once per core.
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Originally-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The secondary threads should enter deep idle states so as to gain maximum
powersavings when the entire core is offline. To do so the offline path
must be made aware of the available deepest idle state. Hence probe the
device tree for the possible idle states in powernv core code and
expose the deepest idle state through flags.
Since the device tree is probed by the cpuidle driver as well, move
the parameters required to discover the idle states into an appropriate
common place to both the driver and the powernv core code.
Another point is that fastsleep idle state may require workarounds in
the kernel to function properly. This workaround is introduced in the
subsequent patches. However neither the cpuidle driver or the hotplug
path need be bothered about this workaround.
They will be taken care of by the core powernv code.
Originally-by: Srivatsa S. Bhat <srivatsa@mit.edu>
Signed-off-by: Preeti U. Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Reviewed-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: linux-pm@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Currently, when going idle, we set the flag indicating that we are in
nap mode (paca->kvm_hstate.hwthread_state) and then execute the nap
(or sleep or rvwinkle) instruction, all with the MMU on. This is bad
for two reasons: (a) the architecture specifies that those instructions
must be executed with the MMU off, and in fact with only the SF, HV, ME
and possibly RI bits set, and (b) this introduces a race, because as
soon as we set the flag, another thread can switch the MMU to a guest
context. If the race is lost, this thread will typically start looping
on relocation-on ISIs at 0xc...4400.
This fixes it by setting the MSR as required by the architecture before
setting the flag or executing the nap/sleep/rvwinkle instruction.
Cc: stable@vger.kernel.org
[ shreyas@linux.vnet.ibm.com: Edited to handle LE ]
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull tty/serial driver updates from Greg KH:
"Here's the big tty/serial driver update for 3.19-rc1.
There are a number of TTY core changes/fixes in here from Peter Hurley
that have all been teted in linux-next for a long time now. There are
also the normal serial driver updates as well, full details in the
changelog below"
* tag 'tty-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (219 commits)
serial: pxa: hold port.lock when reporting modem line changes
tty-hvsi_lib: Deletion of an unnecessary check before the function call "tty_kref_put"
tty: Deletion of unnecessary checks before two function calls
n_tty: Fix read_buf race condition, increment read_head after pushing data
serial: of-serial: add PM suspend/resume support
Revert "serial: of-serial: add PM suspend/resume support"
Revert "serial: of-serial: fix up PM ops on no_console_suspend and port type"
serial: 8250: don't attempt a trylock if in sysrq
serial: core: Add big-endian iotype
serial: samsung: use port->fifosize instead of hardcoded values
serial: samsung: prefer to use fifosize from driver data
serial: samsung: fix style problems
serial: samsung: wait for transfer completion before clock disable
serial: icom: fix error return code
serial: tegra: clean up tty-flag assignments
serial: Fix io address assign flow with Fintek PCI-to-UART Product
serial: mxs-auart: fix tx_empty against shift register
serial: mxs-auart: fix gpio change detection on interrupt
serial: mxs-auart: Fix mxs_auart_set_ldisc()
serial: 8250_dw: Use 64-bit access for OCTEON.
...
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
Pull squashfs update from Phillip Lougher:
"These patches optionally add LZ4 compression support to Squashfs.
LZ4 is a lightweight compression algorithm which can be used on
embedded systems to reduce CPU and memory overhead (in comparison to
the standard zlib compression).
These patches add the wrapper code to allow Squashfs to use the
existing LZ4 decompression code, and the necessary configuration
option"
* tag 'squashfs-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/pkl/squashfs-next:
Squashfs: Add LZ4 compression configuration option
Squashfs: add LZ4 compression support
Pull take two of the GPIO updates:
"Same stuff as last time, now with a fixup patch for the previous
compile error plus I ran a few extra rounds of compile-testing.
This is the bulk of GPIO changes for the v3.19 series:
- A new API that allows setting more than one GPIO at the time. This
is implemented for the new descriptor-based API only and makes it
possible to e.g. toggle a clock and data line at the same time, if
the hardware can do this with a single register write. Both
consumers and drivers need new calls, and the core will fall back
to driving individual lines where needed. Implemented for the
MPC8xxx driver initially
- Patched the mdio-mux-gpio and the serial mctrl driver that drives
modems to use the new multiple-setting API to set several signals
simultaneously
- Get rid of the global GPIO descriptor array, and instead allocate
descriptors dynamically for each GPIO on a certain GPIO chip. This
moves us closer to getting rid of the limitation of using the
global, static GPIO numberspace
- New driver and device tree bindings for 74xx ICs
- New driver and device tree bindings for the VF610 Vybrid
- Support the RCAR r8a7793 and r8a7794
- Guidelines for GPIO device tree bindings trying to get things a bit
more strict with the advent of combined device properties
- Suspend/resume support for the MVEBU driver
- A slew of minor fixes and improvements"
* tag 'gpio-v3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (33 commits)
gpio: mcp23s08: fix up compilation error
gpio: pl061: document gpio-ranges property for bindings file
gpio: pl061: hook request if gpio-ranges avaiable
gpio: mcp23s08: Add option to configure IRQ output polarity as active high
gpio: fix deferred probe detection for legacy API
serial: mctrl_gpio: use gpiod_set_array function
mdio-mux-gpio: Use GPIO descriptor interface and new gpiod_set_array function
gpio: remove const modifier from gpiod_get_direction()
gpio: remove gpio_descs global array
gpio: mxs: implement get_direction callback
gpio: em: Use dynamic allocation of GPIOs
gpio: Check if base is positive before calling gpio_is_valid()
gpio: mcp23s08: Add simple IRQ support for SPI devices
gpio: mcp23s08: request a shared interrupt
gpio: mcp23s08: Do not free unrequested interrupt
gpio: rcar: Add r8a7793 and r8a7794 support
gpio-mpc8xxx: add mpc8xxx_gpio_set_multiple function
gpiolib: allow simultaneous setting of multiple GPIO outputs
gpio: mvebu: add suspend/resume support
gpio: gpio-davinci: remove duplicate check on resource
..
Pull aio updates from Benjamin LaHaise.
* git://git.kvack.org/~bcrl/aio-next:
aio: Skip timer for io_getevents if timeout=0
aio: Make it possible to remap aio ring
This reverts commit 16b7c275c0.
My previous commit 16b7c275c0 ("tools: cpupower: fix return checks for
sysfs_get_idlestate_count()") was not correct. After looking
at the changelog for cpupower I noticed that Thomas had changed the return of
sysfs_get_idlestate_count() to an unsigned int to simplify the code. The
problem is really that both he (in his original change) and I (in my new
change) missed the obvious that sysfs_get_idlestate_count()
can't return -ENODEV. It should just return 0 for "no c-states".
Fixes: 16b7c275c0 (tools: cpupower: fix return checks for ...)
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 2ae83bf938 ("[CIFS] Fix setting time before epoch (negative
time values)") changed "u64 t" to "s64 t", which makes do_div() complain
about a pointer signedness mismatch:
CC fs/cifs/netmisc.o
In file included from ./arch/mips/include/asm/div64.h:12:0,
from include/linux/kernel.h:124,
from include/linux/list.h:8,
from include/linux/wait.h:6,
from include/linux/net.h:23,
from fs/cifs/netmisc.c:25:
fs/cifs/netmisc.c: In function ‘cifs_NTtimeToUnix’:
include/asm-generic/div64.h:43:28: warning: comparison of distinct pointer types lacks a cast [enabled by default]
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
^
fs/cifs/netmisc.c:941:22: note: in expansion of macro ‘do_div’
ts.tv_nsec = (long)do_div(t, 10000000) * 100;
Introduce a temporary "u64 abs_t" variable to fix this.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Steve French <steve.french@primarydata.com>
We have encountered failures when When testing smb2 mounts on ppc64
machines when using both Samba as well as Windows 2012.
On poking around, the problem was determined to be caused by the
high endian MessageID passed in the header for smb2. On checking the
corresponding MID for smb1 is converted to LE before being sent on the
wire.
We have tested this patch successfully on a ppc64 machine.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
Pull md updates from Neil Brown:
"Three fixes for md.
I did have a largish set of locking changes queued, but late testing
showed they weren't quite as stable as I thought and while I fixed
what I found, I decided it safer to delay them a release ...
particularly as I'll be AFK for a few weeks. So expect a larger batch
next time :-)"
* tag 'md/3.19' of git://neil.brown.name/md:
md: Check MD_RECOVERY_RUNNING as well as ->sync_thread.
md: fix semicolon.cocci warnings
md/raid5: fetch_block must fetch all the blocks handle_stripe_dirtying wants.
Pull x86 fixes from Ingo Molnar:
"Misc fixes (mainly Andy's TLS fixes), plus a cleanup"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tls: Disallow unusual TLS segments
x86/tls: Validate TLS entries to protect espfix
MAINTAINERS: Add me as x86 VDSO submaintainer
x86/asm: Unify segment selector defines
x86/asm: Guard against building the 32/64-bit versions of the asm-offsets*.c file directly
x86_64, switch_to(): Load TLS descriptors before switching DS and ES
x86/mm: Use min() instead of min_t() in the e820 printout code
x86/mm: Fix zone ranges boot printout
x86/doc: Update documentation after file shuffling
Commit af906faabc ("Input: gpio_keys - fix warning regarding uninitialized
'irq' variable") introduced the following build warning:
drivers/input/keyboard/gpio_keys.c:625:16: warning: 'button' may be used uninitialized in this function [-Wmaybe-uninitialized]
Move the 'button' initialization to a proper location to avoid such warning.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
virtio 1.0 spec says:
Drivers MUST NOT assume reads from fields greater than 32 bits wide are
atomic, nor are reads from multiple fields: drivers SHOULD read device
configuration space fields like so:
u32 before, after;
do {
before = get_config_generation(device);
// read config entry/entries.
after = get_config_generation(device);
} while (after != before);
Do exactly this, for transports that support it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This code causes a static checker warning:
sound/firewire/oxfw/oxfw.c:46 detect_loud_models()
warn: signedness bug returning '(-2)'
The detect_loud_models() function should return false on falure, so that
we don't try to set up the loud code for hardware that doesn't support
it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add macro to disable all legacy register defines.
Helpful to make sure legacy macros don't leak
through into modern code.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
New FW has chunks that are larger than the size limit of the
FH's DMA. To make sure we don't crash it - actively limit the
max size of each chunk.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the very unlikely case in which no firmware could be,
found. the same pointer was freed twice. Fix that.
Fixes: 490fefebb6 ("iwlwifi: define the .ucode file format for debug")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we reset the device, the CSR_INT gets cleared as well
as CSR_INT_MASK. Meaning that we shouldn't get any interrupt
but, due to a hardware bug, recent devices will keep sending
interrupts. This leads to an interrupt storm while stopping
the device.
The way to fix this is to ACK all the interrupts after the
device is reset so that the value of CSR_INT will stay
0xffffffff.
Fixes: 522713c81e ("iwlwifi: pcie: properly reset the device")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
On stop(), we already cleared our internal state,
and the restart_complete() callback won't be
called, so simply clear the IN_HW_RESTART flag.
Keeping the flag might result in invalid state
on the next start(), preventing the driver starting
properly.
Additionally, don't take IWL_MVM_REF_UCODE_DOWN on stop()
if hw restart was requested, as the ref was already
taken in this case.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Users have no business installing custom code segments into the
GDT, and segments that are not present but are otherwise valid
are a historical source of interesting attacks.
For completeness, block attempts to set the L bit. (Prior to
this patch, the L bit would have been silently dropped.)
This is an ABI break. I've checked glibc, musl, and Wine, and
none of them look like they'll have any trouble.
Note to stable maintainers: this is a hardening patch that fixes
no known bugs. Given the possibility of ABI issues, this
probably shouldn't be backported quickly.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@vger.kernel.org # optional
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: security@kernel.org <security@kernel.org>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
