gem devices designed with multiqueue CANNOT work without this patch.
When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.
For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.
Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.
Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).
Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.
Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.
When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quentin Lambert says:
====================
Remove redundant function
tasklet_hi_enable and tasklet_enable are redundant. Since
tasklet_hi_enable is used only 6 times in 1 file, the first
patch changes calls to the function with calls to tasklet_enable.
The second patch removes tasklet_hi_enable definition.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull pstore update #2 from Tony Luck:
"Couple of pstore-ram enhancements to allow use of different memory
attributes"
* tag 'please-pull-morepstore' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
pstore-ram: Allow optional mapping with pgprot_noncached
pstore-ram: Fix hangs by using write-combine mappings
Pull btrfs update from Chris Mason:
"From a feature point of view, most of the code here comes from Miao
Xie and others at Fujitsu to implement scrubbing and replacing devices
on raid56. This has been in development for a while, and it's a big
improvement.
Filipe and Josef have a great assortment of fixes, many of which solve
problems corruptions either after a crash or in error conditions. I
still have a round two from Filipe for next week that solves
corruptions with discard and block group removal"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (62 commits)
Btrfs: make get_caching_control unconditionally return the ctl
Btrfs: fix unprotected deletion from pending_chunks list
Btrfs: fix fs mapping extent map leak
Btrfs: fix memory leak after block remove + trimming
Btrfs: make btrfs_abort_transaction consider existence of new block groups
Btrfs: fix race between writing free space cache and trimming
Btrfs: fix race between fs trimming and block group remove/allocation
Btrfs, replace: enable dev-replace for raid56
Btrfs: fix freeing used extents after removing empty block group
Btrfs: fix crash caused by block group removal
Btrfs: fix invalid block group rbtree access after bg is removed
Btrfs, raid56: fix use-after-free problem in the final device replace procedure on raid56
Btrfs, replace: write raid56 parity into the replace target device
Btrfs, replace: write dirty pages into the replace target device
Btrfs, raid56: support parity scrub on raid56
Btrfs, raid56: use a variant to record the operation type
Btrfs, scrub: repair the common data on RAID5/6 if it is corrupted
Btrfs, raid56: don't change bbio and raid_map
Btrfs: remove unnecessary code of stripe_index assignment in __btrfs_map_block
Btrfs: remove noused bbio_ret in __btrfs_map_block in condition
...
Pull HID updates from Jiri Kosina:
- i2c-hid race condition fix from Jean-Baptiste Maneyrol
- Logitech driver now supports vendor-specific HID++ protocol, allowing
us to deliver a full multitouch support on wider range of Logitech
touchpads. Written by Benjamin Tissoires
- MS Surface Pro 3 Type Cover support added by Alan Wu
- RMI touchpad support improvements from Andrew Duggan
- a lot of updates to Wacom driver from Jason Gerecke and Ping Cheng
- various small fixes all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (56 commits)
HID: rmi: The address of query8 must be calculated based on which query registers are present
HID: rmi: Check for additional ACM registers appended to F11 data report
HID: i2c-hid: prevent buffer overflow in early IRQ
HID: logitech-hidpp: disable io in probe error path
HID: logitech-hidpp: add boundary check for name retrieval
HID: logitech-hidpp: check name retrieval return code
HID: logitech-hidpp: do not return the name length
HID: wacom: Report input events for each finger on generic devices
HID: wacom: Initialize MT slots for generic devices at post_parse_hid
HID: wacom: Update maximum X/Y accounding to outbound offset
HID: wacom: Add support for DTU-1031X
HID: wacom: add defines for new Cintiq and DTU outbound tracking
HID: wacom: fix freeze on open when autosuspend is on
HID: wacom: re-add accidentally dropped Lenovo PID
HID: make hid_report_len as a static inline function in hid.h
HID: wacom: Consult the application usage when determining field type
HID: wacom: PAD is independent with pen/touch
HID: multitouch: Add quirk for VTL touch panels
HID: i2c-hid: fix race condition reading reports
HID: wacom: Add angular resolution data to some ABS axes
...
drivers/iio/imu/kmx61.c:422:5: sparse: symbol 'kmx61_set_wake_up_odr' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull UBI/UBIFS updates from Artem Bityutskiy:
"This includes the following UBI/UBIFS changes:
- UBI debug messages now include the UBI device number. This change
is responsible for the big diffstat since it touched every
debugging print statement.
- An Xattr bug-fix which fixes SELinux support
- Several error path fixes in UBI/UBIFS"
* tag 'upstream-3.19-rc1' of git://git.infradead.org/linux-ubifs:
UBI: Fix invalid vfree()
UBI: Fix double free after do_sync_erase()
UBIFS: fix a couple bugs in UBIFS xattr length calculation
UBI: vtbl: Use ubi_eba_atomic_leb_change()
UBI: Extend UBI layer debug/messaging capabilities
UBIFS: fix budget leak in error path
Pull xfs update from Dave Chinner:
"There's relatively little change in this update; it is mainly bug
fixes, cleanups and more of the on-going libxfs restructuring and
on-disk format header consolidation work.
Details:
- more on-disk format header consolidation
- move some structures shared with userspace to libxfs
- new per-mount workqueue to fix for deadlocks between nested loop
mounted filesystems
- various bug fixes for ENOSPC, stats, quota off and preallocation
- a bunch of compiler warning fixes for set-but-unused variables
- various code cleanups"
* tag 'xfs-for-linus-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (24 commits)
xfs: split metadata and log buffer completion to separate workqueues
xfs: fix set-but-unused warnings
xfs: move type conversion functions to xfs_dir.h
xfs: move ftype conversion functions to libxfs
xfs: lobotomise xfs_trans_read_buf_map()
xfs: active inodes stat is broken
xfs: cleanup xfs_bmse_merge returns
xfs: cleanup xfs_bmse_shift_one goto mess
xfs: fix premature enospc on inode allocation
xfs: overflow in xfs_iomap_eof_align_last_fsb
xfs: fix simple_return.cocci warning in xfs_bmse_shift_one
xfs: fix simple_return.cocci warning in xfs_file_readdir
libxfs: fix simple_return.cocci warnings
xfs: remove unnecessary null checks
xfs: merge xfs_inum.h into xfs_format.h
xfs: move most of xfs_sb.h to xfs_format.h
xfs: merge xfs_ag.h into xfs_format.h
xfs: move acl structures to xfs_format.h
xfs: merge xfs_dinode.h into xfs_format.h
xfs: catch invalid negative blknos in _xfs_buf_find()
...
Pull ext4 updates from Ted Ts'o:
"Lots of bugs fixes, including Zheng and Jan's extent status shrinker
fixes, which should improve CPU utilization and potential soft lockups
under heavy memory pressure, and Eric Whitney's bigalloc fixes"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (26 commits)
ext4: ext4_da_convert_inline_data_to_extent drop locked page after error
ext4: fix suboptimal seek_{data,hole} extents traversial
ext4: ext4_inline_data_fiemap should respect callers argument
ext4: prevent fsreentrance deadlock for inline_data
ext4: forbid journal_async_commit in data=ordered mode
jbd2: remove unnecessary NULL check before iput()
ext4: Remove an unnecessary check for NULL before iput()
ext4: remove unneeded code in ext4_unlink
ext4: don't count external journal blocks as overhead
ext4: remove never taken branch from ext4_ext_shift_path_extents()
ext4: create nojournal_checksum mount option
ext4: update comments regarding ext4_delete_inode()
ext4: cleanup GFP flags inside resize path
ext4: introduce aging to extent status tree
ext4: cleanup flag definitions for extent status tree
ext4: limit number of scanned extents in status tree shrinker
ext4: move handling of list of shrinkable inodes into extent status code
ext4: change LRU to round-robin in extent status tree shrinker
ext4: cache extent hole in extent status tree for ext4_da_map_blocks()
ext4: fix block reservation for bigalloc filesystems
...
Make the extent buffer allocation interface consistent. Cloned eb will
set a valid fs_info. For dummy eb, we can drop the length parameter and
set it from fs_info.
The built-in sanity checks may pass a NULL fs_info that's queried for
nodesize, but we know it's 4096.
Signed-off-by: David Sterba <dsterba@suse.cz>
Finally it's clear that the requested blocksize is always equal to
nodesize, with one exception, the superblock.
Superblock has fixed size regardless of the metadata block size, but
uses the same helpers to initialize sys array/chunk tree and to work
with the chunk items. So it pretends to be an extent_buffer for a
moment, btrfs_read_sys_array is full of special cases, we're adding one
more.
Signed-off-by: David Sterba <dsterba@suse.cz>
This chip is present on older revisions of the DE2 development kit.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip is present on the Nios2 Development Kit 2C35.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware 1.12.25.0 added support for QSA module, adding the driver code for it.
Also fixes some ethtool get settings for other module types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karen Xie says:
====================
cxgb4/cxgbi: misc. fixes for cxgb4i
This patch set fixes cxgb4i's tx credit calculation and adds handling of
additional rx message and negative advice types. It also removes the duplicate
code in cxgb4i to set the outgoing queues of a packet.
Karen Xie (7):
cxgb4i: fix tx immediate data credit check
cxgb4i: fix credit check for tx_data_wr
cxgb4/cxgb4i: set max. outgoing pdu length in the f/w
cxgb4i: add more types of negative advice
cxgb4i: handle non pdu-aligned rx data
cxgb4i: use cxgb4's set_wr_txq() for setting outgoing queues
libcxgbi: fix the debug print accessing skb after it is freed
Sending to net as the fixes are mostly in the network area and it touches
cxgb4's header file (t4fw_api.h).
v2 corrects the "CHECK"s flagged by checkpatch.pl --strict.
v3 splits the 3rd patch from v2 to two separate patches. Adds detailed commit
messages and makes subject more concise. Patch 3/6 also changes the return
value of is_neg_adv() from int to bool.
v4 -- please ignore.
v5 splits the 1st patch from v3 to two separate patches and reduces code
duplication in make_tx_data_wr().
v6 removed the code style cleanup in the 2nd patch. The style update will be
addressed in a separate patch.
v7 updates the 7th patch with more detailed commit message.
v8 removes the duplicate subject lines from the message bodies.
v9 reformatted the commit messages to be max. 80 characters per line.
v10 rebased to net-next tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With debug turned on the debug print would access the skb after it is freed.
Fix it to free the skb after the debug print.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use cxgb4's set_wr_txq() for setting of the tx queue for a outgoing packet.
remove the similar function in cxgb4i.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abort the connection upon receiving of cpl_rx_data, which means the pdu cannot
be recovered from the tcp stream. This generally is due to pdu header
corruption.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat both CPL_ERR_KEEPALV_NEG_ADVICE and CPL_ERR_PERSIST_NEG_ADVICE as
negative advice.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Programs the firmware of the maximum outgoing iscsi pdu length per connection.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make sure any tx credit related checking is done before adding the wr header.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only data skbs need the wr header added while control skbs do not. Make sure
they are treated differently.
Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building the bcmgenet driver as module, I get:
ERROR: "fixed_phy_register" [drivers/net/ethernet/broadcom/genet/genet.ko] undefined!
commit b0ba512e225d72 ("net: bcmgenet: enable driver to work without device
tree") which added a call to fixed_phy_register. But fixed_phy_register
needs to be exported if used from a module.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses an issue with the level compression of the fib_trie.
Specifically in the case of adding a new leaf that triggers a new node to
be added that takes the place of the old node. The result is a trie where
the 1 child tnode is on one side and one leaf is on the other which gives
you a very deep trie. Below is the script I used to generate a trie on
dummy0 with a 10.X.X.X family of addresses.
ip link add type dummy
ipval=184549374
bit=2
for i in `seq 1 23`
do
ifconfig dummy0:$bit $ipval/8
ipval=`expr $ipval - $bit`
bit=`expr $bit \* 2`
done
cat /proc/net/fib_triestat
Running the script before the patch:
Local:
Aver depth: 10.82
Max depth: 23
Leaves: 29
Prefixes: 30
Internal nodes: 27
1: 26 2: 1
Pointers: 56
Null ptrs: 1
Total size: 5 kB
After applying the patch and repeating:
Local:
Aver depth: 4.72
Max depth: 9
Leaves: 29
Prefixes: 30
Internal nodes: 12
1: 3 2: 2 3: 7
Pointers: 70
Null ptrs: 30
Total size: 4 kB
What this fix does is start the rebalance at the newly created tnode
instead of at the parent tnode. This way if there is a gap between the
parent and the new node it doesn't prevent the new tnode from being
coalesced with any pre-existing nodes that may have been pushed into one
of the new nodes child branches.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the real device can segment packets by software, a vlan device
can set TSO/UFO even when the real device doesn't have those features.
Unlike GSO, this allows packets to be segmented after Qdisc.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have a race between the schedule timing out and the command
completing, we could have the task issuing the command exit
nvme_submit_sync_cmd() while the irq is running sync_completion().
If that happens, we could be corrupting memory, since the stack
that held 'cmdinfo' is no longer valid.
Fix this by always calling nvme_abort_cmd_info(). Once that call
completes, we know that we have either run sync_completion() if
the completion came in, or that we will never run it since we now
have special_completion() as the command callback handler.
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We use WUFE (Wake Up from Sleep Engine) and BTSE (Back to Sleep Engine)
to detect general motion input.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
During imx_thermal probe we have the following log:
[ 1.514819] imx_thermal 2000000.aips-bus:tempmon: failed to register cpufreq cooling device: -517
[ 1.515064] platform 2000000.aips-bus:tempmon: Driver imx_thermal requests probe deferral
Avoid printing the error message in the EPROBE_DEFER case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Per sensor state (ACTIVE/STANDBY) is saved in driver's
private data (acc_stby/mag_stby) and restored when
resume is called.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
By default both sensors are ACTIVE, in this way the driver
will work even if CONFIG_PM_RUNTIME is not selected.
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
This driver uses two IIO devices one for accelerometer and one for magnetometer.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 04489eeb02 ("ALSA: wm8750: add missing VREF output") added the
previously missing VREF widget. And while adding the widget as OUTPUT widget
silences the error of the missing widget it should have rather been a VMID
widget.
The VREF widget is only used internally as a source for the VREF input of
the Out3 Mux. Selecting that input means that the path should be kept
powered up at the VREF/VMID voltage, but that there is no actual audio
signal. Using a VMID widget will do this, whereas using a OUTPUT widget will
simply cause the path to completely power down.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two halves of this part can run largely independently. Hence
a version 4 of this patch followed that reorganized things completely.
This reverts commit d7d787d291.
The codec driver uses regmap to do i2c read/write.
The codec driver started to use REGMAP_IRQ since:
5e3363ad1b
ASoC: rt5677: add GPIO IRQ support
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Invalid buck4 configuration for linear mapping of voltage in S2MPS14
regulators caused boot failure on Gear 2 (dw_mmc-exynos):
[ 3.569137] EXT4-fs (mmcblk0p15): mounted filesystem with ordered data mode. Opts: (null)
[ 3.571716] VFS: Mounted root (ext4 filesystem) readonly on device 179:15.
[ 3.629842] mmcblk0: error -110 sending status command, retrying
[ 3.630244] mmcblk0: error -110 sending status command, retrying
[ 3.636292] mmcblk0: error -110 sending status command, aborting
Buck4 voltage regulator has different minimal voltage value than other
bucks. Commit merging multiple regulator description macros caused to
use linear_min_sel from buck[1235] regulators as value for buck4. This
lead to lower voltage of buck4 than required.
Output of the buck4 is used internally as power source for
LDO{3,4,7,11,19,20,21,23}. On Gear 2 board LDO11 is used as MMC
regulator (V_EMMC_1.8V).
Fixes: 5a867cf288 ("regulator: s2mps11: Optimize the regulator description macro")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
Since multicast frames are marked as no-ack, using
IEEE80211_TX_STAT_ACK to check if they have been
successfully transmitted by the driver is incorrect
since a driver can choose to ignore transmission status
for no-ack frames. This results in incorrect accounting
for such frames.
To fix this issue, this patch introduces a new flag
that can be used by drivers to indicate error-free
transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
[add a note about not setting the flag for non-no-ack frames]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
