The help text of CONFIG_MTD_OF_PARTS refers to additional documentation
in booting-without-of.txt but this documentation was moved to another
file in commit efcc2da3fd (Stefan Roese:
Factor MTD physmap bindings out of booting-without-of). This updates the
help text to point to the right place.
Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
[Brian: fixed doc reference]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
update a comment in nand_command_lp() about specific requirements of
individual commands, the DEPLETE1 command was removed in the past and
the comment no longer applied
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since commit 89168b4899 ("mmc: core: restore detect line inversion
semantics"), the SD card on i.MX28 (and possibly other) devices isn't
detected and booting stops at:
[ 4.120617] Waiting for root device /dev/mmcblk0p3...
This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly
when the host controller doesn't use a GPIO for card detection (but
instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will
return before assigning to the gpio_invert variable, leaving the
variable uninitialized. The variable then gets used to set the flag.
This patch fixes the issue by making sure gpio_invert is set to false
when a GPIO isn't used. After this patch, i.MX28 boots fine.
The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly
for the exact same reason (it uses the same uninitialized variable), so
this patch fixes that too.
Fixes: 89168b4899 ("mmc: core: restore detect line inversion semantics")
Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the DDR Quad read, the dummy cycles maybe 3 or 6 which is less then 8.
The dummy cycles is actually 8 for SPI fast/dual/quad read.
This patch makes preparations for the DDR quad read, it fixes the wrong dummy
value for both the spi-nor.c and m25p80.c.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
NAND devices with page sizes over 4 KiB require more than 4-bits of ECC
coverage. This patch calculates the value of ecc_bytes based on a still
assumed 512-byte step size (13-bits) and the ecc_strength.
Example:
Micron M73A devices (8 KiB page) require 8-bit ECC per 512-byte
Signed-off-by: Jordan Friendshuh <jfriendshuh@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Zoltan HERPAI <wigyori@uid0.hu>
In the absence of a DTB configuration table, the EFI stub will happily
continue attempting to boot a kernel, despite the fact that this kernel
may not function without a description of the hardware. In this case, as
with a typo'd "dtb=" option (e.g. "dbt=") or many other possible
failures, the only output seen by the user will be the rather terse
output from the EFI stub:
EFI stub: Booting Linux Kernel...
To aid those attempting to debug such failures, this patch adds a notice
when no DTB is found, making the output more helpful:
EFI stub: Booting Linux Kernel...
EFI stub: Generating empty DTB
Additionally, a positive acknowledgement is added when a user-specified
DTB is in use:
EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from command line
Similarly, a positive acknowledgement is added when a DTB from a
configuration table is in use:
EFI stub: Booting Linux Kernel...
EFI stub: Using DTB from configuration table
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This sets the DMI string, containing system type, serial number,
firmware version etc. as dump stack arch description, so that oopses
and other kernel stack dumps automatically have this information
included, if available.
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
SMBIOS is important for server hardware vendors. It implements a spec for
providing descriptive information about the platform. Things like serial
numbers, physical layout of the ports, build configuration data, and the like.
Signed-off-by: Yi Li <yi.li@linaro.org>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The DMTF SMBIOS reference spec v3.0.0 defines a new 64-bit entry point,
which enables support for SMBIOS structure tables residing at a physical
offset over 4 GB. This is especially important for upcoming arm64
platforms whose system RAM resides entirely above the 4 GB boundary.
For the UEFI case, this code attempts to detect the new SMBIOS 3.0
header magic at the offset passed in the SMBIOS3_TABLE_GUID UEFI
configuration table. If this configuration table is not provided, or
if we fail to parse the header, we fall back to using the legacy
SMBIOS_TABLE_GUID configuration table. This is in line with the spec,
that allows both configuration tables to be provided, but mandates that
they must point to the same structure table, unless the version pointed
to by the 64-bit entry point is a superset of the 32-bit one.
For the non-UEFI case, the detection logic is modified to look for the
SMBIOS 3.0 header magic before it looks for the legacy header magic.
Note that this patch is based on version 3.0.0d [draft] of the
specification, which is expected not to deviate from the final version
in ways that would affect the correctness of this implementation.
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Tested-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
This adds support to the UEFI side for detecting the presence of
a SMBIOS 3.0 64-bit entry point. This allows the actual SMBIOS
structure table to reside at a physical offset over 4 GB, which
cannot be supported by the legacy SMBIOS 32-bit entry point.
Since the firmware can legally provide both entry points, store
the SMBIOS 3.0 entry point in a separate variable, and let the
DMI decoding layer decide which one will be used.
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The EFI_CONFIG_TABLES bit already gets set by efi_config_init(),
so there is no reason to set it again after this function returns
successfully.
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Instead of reserving the memory regions based on which types we know
need to be reserved, consider only regions of the following types as
free for general use by the OS:
EFI_LOADER_CODE
EFI_LOADER_DATA
EFI_BOOT_SERVICES_CODE
EFI_BOOT_SERVICES_DATA
EFI_CONVENTIONAL_MEMORY
Note that this also fixes a problem with the original code, which would
misidentify a EFI_RUNTIME_SERVICES_DATA region as not reserved if it
does not have the EFI_MEMORY_RUNTIME attribute set. However, it is
perfectly legal for the firmware not to request a virtual mapping for
EFI_RUNTIME_SERVICES_DATA regions that contain configuration tables, in
which case the EFI_MEMORY_RUNTIME attribute would not be set.
Acked-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Change our PE/COFF header to use the minimum file alignment of
512 bytes (0x200), as mandated by the PE/COFF spec v8.3
Also update the linker script so that the Image file itself is also a
round multiple of FileAlignment.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Position independent AArch64 code needs to be linked and loaded at the
same relative offset from a 4 KB boundary, or adrp/add and adrp/ldr
pairs will not work correctly. (This is how PC relative symbol
references with a 4 GB reach are emitted)
We need to declare this in the PE/COFF header, otherwise the PE/COFF
loader may load the Image and invoke the stub at an offset which
violates this rule.
Reviewed-by: Roy Franz <roy.franz@linaro.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
After the EFI stub has done its business, it jumps into the kernel by
branching to offset #0 of the loaded Image, which is where it expects
to find the header containing a 'branch to stext' instruction.
However, the UEFI spec 2.1.1 states the following regarding PE/COFF
image loading:
"A UEFI image is loaded into memory through the LoadImage() Boot
Service. This service loads an image with a PE32+ format into memory.
This PE32+ loader is required to load all sections of the PE32+ image
into memory."
In other words, it is /not/ required to load parts of the image that are
not covered by a PE/COFF section, so it may not have loaded the header
at the expected offset, as it is not covered by any PE/COFF section.
So instead, jump to 'stext' directly, which is at the base of the
PE/COFF .text section, by supplying a symbol 'stext_offset' to
efi-entry.o which contains the relative offset of stext into the Image.
Also replace other open coded calculations of the same value with a
reference to 'stext_offset'
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Roy Franz <roy.franz@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
The drivers/mtd/nand/gpio.c driver does not GPIO bitbang the complete
NAND protocol, but instead is GPIO _assisted_ -- a memory mapped interface
communicates commands and data, and only few control signals are connected
to GPIO pins.
Expand comments in the driver source and in the Kconfig description to
better reflect the very nature of the driver. The previous text could be
mistaken for complete GPIO bitbanging.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Expand the description of the 'gpios' property in the GPIO assisted
NAND flash binding, to explicitly list the required GPIO pin references
and their order.
Update the example section to individually bracket the GPIO references,
and capitalize the signal names for improved readability.
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Without the fix, the mute led can't work on these three machines.
After apply this fix, these three machines will fall back on the led
control quirk as below, and through testing, the mute led works very
well.
PIN_QUIRK(0x10ec0282, 0x103c, "HP", ALC269_FIXUP_HP_LINE1_MIC1_LED,
ALC282_STANDARD_PINS,
{0x12, 0x90a60140},
...
BugLink: https://bugs.launchpad.net/bugs/1389497
Tested-by: TieFu Chen <tienfu.chen@canonical.com>
Cc: Kailang Yang <kailang@realtek.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alt is booted from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from chosen/bootargs.
This change has a side-effect of changing the console speed from 38400
to 115200. This is intentional as 115200 is consistently used on
all other shmobile boards.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PCI core will soon automatically handle the PCI domain number,
allowing the internal PCI and external PCIe bridges work at the same time.
In order for that to work, we need to enable PCI_DOMAINS.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Lee Jones as a new co-maintainer.
The kernel.org repo moved to allow us both to push to it. Update
MAINTAINERS to match.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.18, 2nd round" from Shawn Guo:
"This is the second round of i.MX fixes for 3.18. The clk-vf610 fix is
relatively big, because it needs some adaption to the change made by
offending commit dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits
from clk-pllv3 driver). And it should have been sent to you for earlier
-rc inclusion, but unfortunately it got delayed for some time because
Stefan wasn't aware of my email address change."
The i.MX fixes for 3.18, 2nd round:
- Fix a regression on Vybrid platform which is caused by commit
dc4805c2e7 (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3
driver), and results in a missing configuration on PLL clocks.
- Fix a regression with i.MX defconfig files where CONFIG_SPI option
gets lost accidentally.
* tag 'imx-fixes-3.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (460 commits)
ARM: imx: Fix the removal of CONFIG_SPI option
ARM: imx: clk-vf610: define PLL's clock tree
+ Linux 3.18-rc3
Signed-off-by: Olof Johansson <olof@lixom.net>
If the OPEN rpc call to the server fails with an ENOENT call, nfs_atomic_open
will create a negative dentry for that file, however it currently fails
to call nfs_set_verifier(), thus causing the dentry to be immediately
revalidated on the next call to nfs_lookup_revalidate() instead of following
the usual lookup caching rules.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
If a system wants to reduce the booting time as a top priority, now we can
use a mount option, -o fastboot.
With this option, f2fs conducts a little bit slow write_checkpoint, but
it can avoid the node page reads during the next mount time.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
__submit_merged_bio f2fs_write_end_io f2fs_write_end_io
wait_io = X wait_io = x
complete(X) complete(X)
wait_io = NULL
wait_for_completion()
free(X)
spin_lock(X)
kernel panic
In order to avoid this, this patch removes the wait_io facility.
Instead, we can use wait_on_all_pages_writeback(sbi) to wait for end_ios.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
If there is a chance to make a huge sized discard command, we don't need
to split it out, since each blkdev_issue_discard should wait one at a
time.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
This patch simplifies the inline_data usage with the following rule.
1. inline_data is set during the file creation.
2. If new data is requested to be written ranges out of inline_data,
f2fs converts that inode permanently.
3. There is no cases which converts non-inline_data inode to inline_data.
4. The inline_data flag should be changed under inode page lock.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Thermal hysteresis represents a temperature difference.
But the original code treats it as a temperature value,
Convert it from tenths of degree Kelvin to Milli-Celsius
by deducing 273200. This is not right.
Kelvin and Celsius have same degree size. From temperature
difference view, the conversion between tenths of degree
Kelvin unit and Milli-Celsius unit is just to multiply 100.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
I've tried to cc all the people who have recently added new stuff
but forgotten to update documentation.
I've also decided not to bother documenting the massive property list
in struct drm_mode_config. If that beast keeps on growing we might want
to extract it into a separate structure which we won't document.
Cc: Thomas Wood <thomas.wood@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
While writing atomic docs I've noticed that I don't get any errors
for my screw-ups in drm_crtc.h. Fix this immediately.
This just does the bare minimum to get starts, lots of stuff isn't
properly documented yet unfortunately.
v2: Fix adjacent spelling error Sean noticed.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a bit of OCD cleanup on headers - this function isn't the core
interface any more but just a helper for drivers who haven't yet
transitioned to universal planes. Put the declaration at the right
spot and sprinkle necessary #includes over all drivers.
Maybe this helps to encourage driver maintainers to do the switch.
v2: Fix #include ordering for tegra, reported by 0-day builder.
v3: Include required headers, reported by Thierry.
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Thierry Reding <treding@nvidia.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Merge "Renesas ARM Based SoC DT Clocksource Updates for v3.19" from Simon
Horman:
* sh_mtu2: Drop incorrect SoC family name
* sh_tmu: Document r8a7778 and r8a7740 bindings
* tag 'renesas-dt-clocksource-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
clocksource: sh_mtu2: Drop incorrect SoC family name
clocksource: sh_tmu: Document r8a7778 binding
clocksource: sh_tmu: Document R-Mobile r8a7740 binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC Cleanup for v3.19" from Simon Horman:
* Remove FSF address from copyright headers
* tag 'renesas-cleanup-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove FSF address from copyright headers
Signed-off-by: Olof Johansson <olof@lixom.net>
Userspace expects to see a long space before the first pulse is sent on
the lirc device. Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything. This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession. When a reset event is delivered, we cannot know
anything about the duration of the space. But it should be safe to
assume it has been a long time and we just set the duration to maximum.
Signed-off-by: Austin Lund <austin.lund@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Merge "first bunch on Rockchip dt changes" from Heiko Stübner:
First hunk of rockchip devicetree patches, containing:
- cpu operating points and supplies
- dma support for spi controllers
- i2s on rk3066 and rk3188
- default core clock settings for rk3288
* tag 'v3.19-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add SPI DMA into rk3288.dtsi
ARM: dts: rockchip: enable init rate for clock
ARM: dts: rockchip: add I2S controllers for rk3066 and rk3188
ARM: dts: rockchip: enable DMA on SPI for rk3066 and rk3188
ARM: dts: rockchip: add cpu supplies to boards
ARM: dts: rockchip: add operating points and armclk references
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC Soc Cleanups for v3.19" from Simon Horman:
* Remove sh73a0_init_delay and r8a7778_init_delay wrappers
* tag 'renesas-soc-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0: Remove wrapper sh73a0_init_delay()
ARM: shmobile: r8a7778: Remove wrapper r8a7778_init_delay()
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC Boards Cleanups for v3.19" from Simon Horman:
* Sort armadillo800eva includes
* tag 'renesas-boards-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: armadillo800eva: Sort includes
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC Kconfig Cleanups for v3.19
* Remove reference to ARCH_HAS_OPP, it has been removed
* tag 'renesas-kconfig-cleanups-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: Remove ARCH_HAS_OPP completely
Signed-off-by: Olof Johansson <olof@lixom.net>
