When a port that was used to listen for inbound connections gets closed
and reused for outgoing connections (like rsh ends up doing for stderr
flow), current we may reject the SYN/ACK packet for the new connection
because tcp_conntracks states forbirds a port to become a client while
there is still a TIME_WAIT entry in there for it.
As TCP may expire the TIME_WAIT socket in 60s and conntrack's timeout
for it is 120s, there is a ~60s window that the application can end up
opening a port that conntrack will end up blocking.
This patch fixes this by simply allowing such state transition: if we
see a SYN, in TIME_WAIT state, on REPLY direction, move it to sSS. Note
that the rest of the code already handles this situation, more
specificly in tcp_packet(), first switch clause.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This adds the MMC/SD card reader (MMCI) block to the
RealView PB1176 DTS file. Add a special MCLK derived clock
and a fixed regulator to represent the 3.3V rail hardwired
to the MMC reader on the board.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Keyboard Mouse Interface (KMI) blocks to the
PB1176 DTS file, and defines the special KMI clock derived
from the 24 MHz chrystal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the PL022 SSP/SPI block to the PL1176 DTS file, also
define the separate SSPCLK clock derived from the 24MHz
chrystal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PB1176 has two PL031 RTC clocks, one in the devchip and one
in the FPGA. Add them to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates a node in the device tree to hold the FPGA devices
as a "simple-bus" and moves the GIC found on the FPGA to this
node, so it reflects the actual topology of the system.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This implements basic device tree boot support for the RealView
platforms, with a basic device tree for ARM PB1176 as an example.
The implementation is done with a new DT-specific board file
using only pre-existing bindings for the basic IRQ, timer and
serial port drivers. A new compatible type is added to the GIC
for the ARM1176.
This implementation uses the MFD syscon handle from day one to
access the system controller registers, and register the devices
using the SoC bus.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh@kernel.org>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'walked' flag was used to avoid walking paths that have already been
walked. But since we started caching the number of inputs and outputs of a
path we never actually get into a situation where we try to walk a path that
has the 'walked' flag set.
There are two cases in which we can end up walking a path multiple times
within a single run of is_connected_output_ep() or is_connected_input_ep().
1) If a path splits up and rejoins later:
.--> C ---v
A -> B E --> F
'--> D ---^
When walking from A to F we'll end up at E twice, once via C and once via D.
But since we do a depth first search we'll fully discover the path and
initialize the number of outputs/inputs of the widget the first time we get
there. The second time we get there we'll use the cached value and not
bother to check any of the paths again. So we'll never see a path where
'walked' is set in this case.
2) If there is a circle:
A --> B <-- C <-.--> F
'--> D ---'
When walking from A to F we'll end up twice at B. But since there is a
circle the 'walking' flag will still be set on B once we get there the
second time. This means we won't look at any of it's outgoing paths. So in
this case we won't ever see a path where 'walked' is set either.
So it is safe to remove the flag. This on one hand means we remove some
always true checks from one of the hottest paths of the DAPM algorithm and
on the other hand means we do not have to do the tedious clearing of the
flag after checking the number inputs or outputs of a widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
dapm_adc_check_power() checks if the widget is active, if yes it only checks
whether there are any connected input paths. Otherwise it calls
dapm_generic_check_power() which will check for both connected input and
output paths. But the function that checks for connected output paths will
return true if the widget is a active sink. Which means the generic power
check function will work just fine and there is no need for a special power
check function.
The same applies for dapm_dac_check_power(), but with input and output paths
reversed.
This patch removes both dapm_adc_check_power() and dapm_dac_check_power()
and replace their usage with dapm_generic_check_power().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
A path has always a valid source and a valid sink otherwise we wouldn't add
it in the first place. Hence all tests that check if sink/source is non NULL
always evaluate to true and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Each widget has a list of all the paths that it is connected to. There is no
need to iterate over all paths when we are only interested in the paths of a
specific widget.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use strncpy() instead of strcpy(). That's not a security issue, as the
source buffer is taken from DT nodes, but we should still enforce bound
checks. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The actions taken in both branches are identical, so we can simplify the
code. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
this is a series of patches to just convert the plain info callback
for enum ctl elements to snd_ctl_elem_info(). Also, it includes the
extension of snd_ctl_elem_info(), for catching the unexpected string
cut-off and handling the zero items.
Some architectures like PARISC is known not to support mmap properly
with the DMA buffer, where dma_mmap_coherent() returns -EINVAL
unconditionally. From the API POV, we should rather drop the mmap
support there and expose it before the user-space tries to call mmap.
The patch contains again ugly ifdef's, unfortunately, as there is no
global flag indicating this. Once when such macro is defined, we can
get rid of this instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that the call to of_match_device() (introduced in commit
df59fa7f ["spi: orion: support armada extended baud rates"]) may return
a NULL if there is no match in the device tree (or perhaps no device tree
at all). Check the return pointer and set the local device data to the
lowest common denominator orion device data if it is NULL.
Reported-by: Karl Beldan <karl.beldan@gmail.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have consistently dma_mmap_coherent() for all architectures,
the current ifdef and arch-specific codes in pcm core can be cleaned
up gracefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently unknown consumer page codes are ignored, which means that they cannot
later be mapped from userspace using udev / hwdb. Map them to KEY_UNKNOWN, so
that userspace can remap them for keyboards which make up their own consumer
page codes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a key is tainted during resume, it is no longer programmed
into the device; however, it's uploaded flag may (will) be set.
Clear the flag when not programming it because it's tainted to
avoid attempting to remove it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the input PGA to work correctly the ALC clock needs to be active.
Otherwise volume changes are not applied.
Fixes: dab464b60b ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: stable@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Entrega is misspelled as Entregra or Entrgra, so fix that.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sometimes the trx offsets are 0, in that case there is no partition and
we should not try to add one.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
[Brian: rewrapped]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the currently existing APIs between mac80211 and the low
level driver to implement WMM admission control.
The low level driver needs to report the media time used by
each transmitted packet in ieee80211_tx_status. Based on that
information, mac80211 will modify the QoS parameters of the
admission controlled Access Category when the limit is
reached. Once the original QoS parameters can be restored,
mac80211 will do so.
One issue with this approach is that management frames will
also erroneously be downgraded, but the upside is that the
implementation is simple. In the future, it can be extended
to driver- or device-based implementations that are better.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no reason to ever set invalid CW_min/CW_max to the
drivers, we should catch it in higher layers. However, the
consequences of setting it wrong can be quite severe, so
double-check at a low level and error out for invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During the review of the corresponding wpa_supplicant patches we
noticed that the only way for it to detect that this functionality
is supported currently is to check for the command support. This
can be misleading though, as the command was also designed to, in
the future, support pure 802.11 TSPECs.
Expose the WMM-TSPEC feature flag to nl80211 so later we can also
expose an 802.11-TSPEC feature flag (if needed) to differentiate
the two cases.
Note: this change isn't needed in 3.18 as there's no driver there
yet that supports the functionality at all.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make drm_mode_add_fb() call drm_mode_add_fb2() after converting its
args to the new internal format, instead of duplicating code.
Also picks up a lot more error checking, which the legacy modes
should pass after being converted to the new format.
Signed-off-by: Chuck Ebbert <cebbert.lkml@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When clk_prepare_enable(q->clk) fails it is clearer to disable the previous
acquired clock (q->clk_en) in the error path rather than doing it locally.
So disable q->clk_en in the error path only.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The 'map_failed' label will return 'ret', so we need to assign the error
code to 'ret', otherwise the probe function will return success.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This replaces kzalloc() and ioremap() calls by devm_ functions
in the probe() routine, which automatically release the corresponding
resources when probe() fails or when the device is removed.
This simplifies simplifies the error management code, and brings
the below improvements or changes:
A. Fixing a bug reported by "make coccicheck":
If "board = devm_kzalloc()" fails, the probe() function jumps
incorrectly to label "no_res" and therefore returns without
running iounmap().
B. Requesting the memory region
Using devm_ioremap_resource() makes the probe() function request
the corresponding memory region before running ioremap(), as
it is supposed to do.
C. Standardizing the error codes:
The use of devm_ioremap_resource() changes the return value:
* -ENOMEM instead of -EIO in case of ioremap() failure,
* -EINVAL instead of -ENODEV in case of platform_get_resource()
failure.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
