The USB PHY member of the HCD structure is renamed to 'usb_phy' and
modifications are done in all drivers accessing it.
This is in preparation to adding the generic PHY support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
[Sergei: added missing 'drivers/usb/misc/lvstest.c' file, resolved rejects,
updated changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "usb: gadget: uvc: rename functions to avoid conflicts with host uvc"
renamed a lot of symbols but missed one references that was inside of
an #ifdef:
drivers/usb/gadget/function/uvc_v4l2.c:363:23: error: 'uvcg_v4l2_get_unmapped_area' undeclared here (not in a function)
.get_unmapped_area = uvcg_v4l2_get_unmapped_area,
^
drivers/usb/gadget/function/uvc_v4l2.c:344:22: warning: 'uvc_v4l2_get_unmapped_area' defined but not used [-Wunused-function]
static unsigned long uvc_v4l2_get_unmapped_area(struct file *file,
^
This renames the reference according the changed function name.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ea95b1108 ("usb: gadget: uvc: rename functions to avoid conflicts with host uvc")
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly added sti ehci and ohci drivers come with a single
Kconfig entry that does not depend on either of the base drivers,
which leads to a link error when they are disabled:
drivers/built-in.o: In function `ohci_platform_init':
:(.init.text+0x14788): undefined reference to `ohci_init_driver'
To fix that, this patch introduces two separate Kconfig options
with proper dependencies, which avoids the problem and is also
more consistent with the other glue drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d115837259 ("usb: host: ohci-st: Add OHCI driver support for ST STB devices")
Cc: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we have completely moved from older USB-PHY drivers
to newer GENERIC-PHY drivers for PHYs available with USB controllers
on Exynos series of SoCs, we can remove the support for the same
in our host drivers too.
We also defer the probe for our host in case we end up getting
EPROBE_DEFER error when getting PHYs.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code only returns -ENOTSUPP for OTG host, but in fact,
embedded host also needs to returns -ENOTSUPP if the peripheral
is not at TPL.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For function and group configuration nodes, use "function"
"groups" string pairs, not "pins" where there should be
"groups".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set multicast support for 6lowpan network interface.
This is needed in every network interface that supports IPv6.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If skb is going to multiple destinations, then make sure that we
do not overwrite the common IPv6 headers. So before compressing
the IPv6 headers, we copy the skb and that is then sent to 6LoWPAN
Bluetooth devices.
This is a similar patch as what was done for IEEE 802.154 6LoWPAN
in commit f19f4f9525 ("ieee802154: 6lowpan: ensure header compression
does not corrupt ipv6 header")
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We refactor the DT parser to look for either a config or a
function and then look for further nodes and reserve maps,
not the two things mixed up like prior to this patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some platforms with no power management capabilities, the hotplug
implementation is allowed to return from a smp_ops.cpu_die() call as a
function return. Upon a CPU onlining event, the KVM CPU notifier tries
to reinstall the hyp stub, which fails on platform where no reset took
place following a hotplug event, with the message:
CPU1: smp_ops.cpu_die() returned, trying to resuscitate
CPU1: Booted secondary processor
Kernel panic - not syncing: unexpected prefetch abort in Hyp mode at: 0x80409540
unexpected data abort in Hyp mode at: 0x80401fe8
unexpected HVC/SVC trap in Hyp mode at: 0x805c6170
since KVM code is trying to reinstall the stub on a system where it is
already configured.
To prevent this issue, this patch adds a check in the KVM hotplug
notifier that detects if the HYP stub really needs re-installing when a
CPU is onlined and skips the installation call if the stub is already in
place, which means that the CPU has not been reset.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The kernel used to contain two functions for length-delimited,
case-insensitive string comparison, strnicmp with correct semantics
and a slightly buggy strncasecmp. The latter is the POSIX name, so
strnicmp was renamed to strncasecmp, and strnicmp made into a wrapper
for the new strncasecmp to avoid breaking existing users.
To allow the compat wrapper strnicmp to be removed at some point in
the future, and to avoid the extra indirection cost, do
s/strnicmp/strncasecmp/g.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch ensures the cpus to kexec/reboot at nominal frequency.
Nominal frequency is the highest cpu frequency on PowerPC at
which the cores can run without getting throttled.
If the host kernel had set the cpus to a low pstate and then it
kexecs/reboots to a cpufreq disabled kernel it would cause the target
kernel to perform poorly. It will also increase the boot up time of
the target kernel. So set the cpus to high pstate, in this case to
nominal frequency before rebooting to avoid such scenarios.
The reboot notifier will set the cpus to nominal frequncy.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Its possible today that the pstate of a core is held at a high even after the
entire core is hotplugged out if a load had just run on the hotplugged cpu. This is
fair, since it is assumed that the pstate does not matter to a cpu in a deep idle
state, which is the expected state of a hotplugged core on powerpc. However on powerpc,
the pstate at a socket level is held at the maximum of the pstates of each core. Even
if the pstates of the active cores on that socket is low, the socket pstate is held
high due to the pstate of the hotplugged core in the above mentioned scenario. This
can cost significant amount of power loss for no good.
Besides, since it is a non active core, nothing can be done from the kernel's end
to set the frequency of the core right. Hence make use of the stop_cpu callback
to explicitly set the pstate of the core to a minimum when the last cpu of the
core gets hotplugged out.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 367dc4aa93 ("cpufreq: Add stop CPU callback to
cpufreq_driver interface") introduced the stop CPU callback for
intel_pstate drivers. During the CPU_DOWN_PREPARE stage, this
callback is invoked so that drivers can take some action on the
pstate of the cpu before it is taken offline. This callback was
assumed to be useful only for those drivers which have implemented
the set_policy CPU callback because they have no other way to take
action about the cpufreq of a CPU which is being hotplugged out
except in the exit callback which is called very late in the offline
process.
The drivers which implement the target/target_index callbacks were
expected to take care of requirements like the ones that commit
367dc4aa addresses in the GOV_STOP notification event. But there
are disadvantages to restricting the usage of stop CPU callback
to cpufreq drivers that implement the set_policy callbacks and who
want to take explicit action on the setting the cpufreq during a
hotplug operation.
1.GOV_STOP gets called for every CPU offline and drivers would usually
want to take action when the last cpu in the policy->cpus mask
is taken offline. As long as there is more than one cpu in the
policy->cpus mask, cpufreq core itself makes sure that the freq
for the other cpus in this mask is set according to the maximum load.
This is sensible and drivers which implement the target_index callback
would mostly not want to modify that. However the cpufreq core leaves a
loose end when the cpu in the policy->cpus mask is the last one to go offline;
it does nothing explicit to the frequency of the core. Drivers may need
a way to take some action here and stop CPU callback mechanism is the
best way to do it today.
2. We cannot implement driver specific actions in the GOV_STOP mechanism.
So we will need another driver callback which is invoked from here which is
unnecessary.
Therefore this patch extends the usage of stop CPU callback to be used
by all cpufreq drivers as long as they have this callback implemented
and irrespective of whether they are set_policy/target_index drivers.
The assumption is if the drivers find the GOV_STOP path to be a suitable
way of implementing what they want to do with the freq of the cpu
going offine,they will not implement the stop CPU callback at all.
Signed-off-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We use cma reserved area for creating guest hash page table.
Don't do the reservation in non-hypervisor mode. This avoids unnecessary
CMA reservation when booting with limited memory configs like
fadump and kdump.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When building this driver as a module, we get a helpful warning
about the return type:
drivers/cpufreq/integrator-cpufreq.c:232:2: warning: initialization from incompatible pointer type
.remove = __exit_p(integrator_cpufreq_remove),
If the remove callback returns void, the caller gets an undefined
value as it expects an integer to be returned. This fixes the
problem by passing down the value from cpufreq_unregister_driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
BDW display - DP buffer translation values changed to give better margin.
Further change to entry 6; set dword 0 bit 31=1.
Both changes were approved already but this one didn't landed BSpec yet
this is why it is in a separated patch. Making reviewer's life easier.
Also alowing separated tests and any future bisect that might be needed.
Reference: Predator r74080 / HSD 4394389
v2: Arthur noticed I was changing the wrong bit.
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's make sure PSR is propperly disabled before to re-enabled it.
According to Spec, after disabled PSR CTL, the Idle state might occur
up to 24ms, that is one full frame time (1/refresh rate),
plus SRD exit training time (max of 6ms),
plus SRD aux channel handshake (max of 1.5ms).
So if something went wrong PSR will be disabled until next full
enable/disable setup.
v2: The 24ms above takes in account 16ms for refresh rate on 60Hz mode. However
on low frequency modes this can take longer. So let's use 50ms for safeness.
v3: Move wait out of psr.lock critical area.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The sw cache clean on BDW is a tempoorary workaround because we cannot
set cache clean on blt ring with risk of hungs. So we are doing the cache clean on sw.
However we are doing much more than needed. Not only when using blt ring.
So, with this extra w/a we minimize the ammount of cache cleans and call it only
on same cases that it was being called on gen7.
The traditional FBC Cache clean happens over LRI on BLT ring when there is a
frontbuffer touch happening. frontbuffer tracking set fbc_dirty variable
to let BLT flush that it must clean FBC cache.
fbc.need_sw_cache_clean works in the opposite information direction
of ring->fbc_dirty telling software on frontbuffer tracking to perform
the cache clean on sw side.
v2: Clean it a little bit and fully check for Broadwell instead of gen8.
v3: Rebase after frontbuffer organization.
v4: Wiggle confused me. So fixing v3!
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
sys_tz is already declared in include/linux/time.h
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jan Kara <jack@suse.cz>
If stat data exceeds wmi-htc buffer limits
firmware splits it into many wmi stats update
events which are delivered in a ping-pong fashion
triggered by wmi stats request command.
Since there's only an implicit start-of-data and
no end-of-data indications the driver has to
perform some trickery to get complete stat data.
kvalo: use %zu to fix a compiler warning and fix a typo in a comment
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Stats were requested and processed for each read
call. This caused inconsistent readings.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The parsing function was rather complex. Simplify
by splitting it up into firmware branch specific
implementations.
While at it move the parsing code into wmi.c where
it belongs.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The return values are not used by callers of these functions
so change the functions to return void.
Other miscellanea:
o add __printf verification to wil6210 logging functions
No format/argument mismatches found
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Given following iptables ruleset:
-P FORWARD DROP
-A FORWARD -m sctp --dport 9 -j ACCEPT
-A FORWARD -p tcp --dport 80 -j ACCEPT
-A FORWARD -p tcp -m conntrack -m state ESTABLISHED,RELATED -j ACCEPT
One would assume that this allows SCTP on port 9 and TCP on port 80.
Unfortunately, if the SCTP conntrack module is not loaded, this allows
*all* SCTP communication, to pass though, i.e. -p sctp -j ACCEPT,
which we think is a security issue.
This is because on the first SCTP packet on port 9, we create a dummy
"generic l4" conntrack entry without any port information (since
conntrack doesn't know how to extract this information).
All subsequent packets that are unknown will then be in established
state since they will fallback to proto_generic and will match the
'generic' entry.
Our originally proposed version [1] completely disabled generic protocol
tracking, but Jozsef suggests to not track protocols for which a more
suitable helper is available, hence we now mitigate the issue for in
tree known ct protocol helpers only, so that at least NAT and direction
information will still be preserved for others.
[1] http://www.spinics.net/lists/netfilter-devel/msg33430.html
Joint work with Daniel Borkmann.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The Kconfig symbol ARCH_HAS_OPP became redundant in v3.16: commit
049d595a4d ("PM / OPP: Make OPP invisible to users in Kconfig")
removed the only dependency that used it. Setting it had no effect
anymore.
So commit 78c5e0bb14 ("PM / OPP: Remove ARCH_HAS_OPP") removed it. For
some reason that commit did not remove all select statements for that
symbol. These statements are now useless. Remove one from devfreq too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
It is possible to turn off the card clock by setting
the frequency to zero via debugfs e.g.
echo 0 > /sys/kernel/debug/mmc0/clock
However that produces an incorrect warning that is
designed to warn if the frequency is below the minimum
operating frequency. So correct the warning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want to know in which cases the user explicitly sets the policy
options. In that case, we also want to dump back the info.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
mmc_gpiod_free_cd() is paired with mmc_gpiod_request_cd()
and both must reference the same device which is the
actual host controller device not the mmc_host class
device.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As of 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe"),
the atmci_probe() function calls atmci_cleanup_slot in the failure path.
This causes a new warning whenever the driver is built:
WARNING: drivers/mmc/host/built-in.o(.init.text+0xa04): Section mismatch in reference from the function atmci_probe() to the function .exit.text:atmci_cleanup_slot()
The function __init atmci_probe() references
a function __exit atmci_cleanup_slot().
Gcc correctly warns about this function getting dropped in the link stage
for the built-in case, which would cause undefined behavior when this error
path is hit. The solution is to simply drop the __exit annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 528bc7808f ("mmc: atmel-mci: Release mmc resources on failure in probe")
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is safe to call the pm sync calls in interrupt context in this driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As written, the __init for ti_clk_get_div_table is in the middle of the return
type.
The gcc documentation indicates that section attributes should be added to the
end of the function declaration:
extern void foobar (void) __attribute__ ((section ("bar")));
However gcc seems to be very permissive with where attributes can be placed.
clang on the other hand isn't so permissive, and fails if you put the section
definition in the middle of the return type:
drivers/clk/ti/divider.c:298:28: error: expected ';' after struct
static struct clk_div_table
^
;
drivers/clk/ti/divider.c:298:1: warning: 'static' ignored on this
declaration [-Wmissing-declarations]
static struct clk_div_table
^
drivers/clk/ti/divider.c:299:9: error: type specifier missing,
defaults to 'int' [-Werror,-Wimplicit-int]
__init *ti_clk_get_div_table(struct device_node *node)
~~~~~~ ^
drivers/clk/ti/divider.c:345:9: warning: incompatible pointer types
returning 'struct clk_div_table *' from a function with result type 'int *' [-Wincompatible-pointer-types]
return table;
^~~~~
drivers/clk/ti/divider.c:419:9: warning: incompatible pointer types
assigning to 'const struct clk_div_table *' from 'int *' [-Wincompatible-pointer-types]
*table = ti_clk_get_div_table(node);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
3 warnings and 2 errors generated.
By convention, most of the kernel code puts section attributes between the
return type and function name. In the case where the return type is a pointer,
it's important to place the '*' on left of the __init.
This updated code works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
I "forgot" to update the dtb and the kernel crashed:
|Unable to handle kernel NULL pointer dereference at virtual address 0000002e
|PC is at __clk_get_flags+0x4/0xc
|LR is at ti_dt_clockdomains_setup+0x70/0xe8
because I did not have the clock nodes. of_clk_get() returns an error
pointer which is not checked here.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
of_clk_add_provider makes an internal copy of the parent_names property
while its called, thus it is no longer needed after this call and can
be freed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Previously, the TI clock driver initialized all the clocks hierarchically
under each separate clock provider node. Now, each clock that requires
IO access will instead check their parent node to find out which IO range
to use.
This patch allows the TI clock driver to use a few new features provided
by the generic of_clk_init, and also allows registration of clock nodes
outside the clock hierarchy (for example, any external clocks.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Stefan Assmann <sassmann@kpanic.de>
Acked-by: Tony Lindgren <tony@atomide.com>
