Moving disable GPEs from enter_sleep up into sleep_prepare fixed
the disabled SCI on S4 on Acer laptops.
However, it caused an immediate S3 resume on the HP nx6125.
Apparently, on the HP, a GPE was getting re-enabled after
the prepare, but before the enter.
Close that window by restoring the GPE disable on enter.
This is redundant in most cases, but closes this window,
where S3 and S4 paths differ.
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Acked-by: Ray Lee <ray-lk@madrabbit.org>
This fixs address defines for IXP4XX_NPE[ABC]_BASE_VIRT.
They are defined as (IXP4XX_PERIPHERAL_BASE_PHYS + 0x[678]000) now,
but they should be defined as (IXP4XX_PERIPHERAL_BASE_VIRT + 0x[678]000). Note PHYS vs VIRT in IXP4XX_PERIPHERAL_BASE...
Signed-off-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The SDHC controllers cannot process shorter transfers.
They has to be handled as longer ones, but it such case CRC
error is evaluated. There was a case in the code still,
where this error is not ignored as it should to be process
these transfers.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only System PLL clock source is selectable by CSCR_SYSTEM_SEL
bit. MPU PLL is driven by 512*CLK32 for each case.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The minimal bus clock prescaler should be kept at value
selected by the board / boot loader designer.
Switching frequency above startup limit could
lead to the external memory/devices misbehave.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes bogus zeroing of unused bits in output reports,
introduced in Simon's patch in commit d4ae650a.
According to the specification, any sane device should not care
about values of unused bits.
What is worse, the zeroing is done in a way which is broken and
might clear certain bits in output reports which are actually
_used_ - a device that has multiple fields with one value of
the size 1 bit each might serve as an example of why this is
bogus - the second call of hid_output_report() would clear the
first bit of report, which has already been set up previously.
This patch will break LEDs on SpaceNavigator, because this device
is broken and takes into account the bits which it shouldn't touch.
The quirk for this particular device will be provided in a separate
patch.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
hid_parser is non-trivially large structure, so it should be allocated
using vmalloc() to avoid unsuccessful allocations when memory fragmentation
is too high.
This structue has a very short life, it's destroyed as soon as the report
descriptor has been completely parsed.
This should be considered a temporary solution, until the hid_parser is
rewritten to consume less memory during report descriptor parsing.
Acked-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The code for performing the calculation was only in the SH-4 probe
path, move it out to the common path so the other parts get this
right too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up some compile failures for cases where we don't include
all of the headers. There's not much point in keeping the struct
references around anyways, most of the others have been converted
already.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
For some reason sh was missing __NR_readahead, even though the
syscall was wired up, and the slot was reserved. Caught with
dwmw2's missing syscall checker.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When a SH7751R system includes a card that has wide range space
like a graphics card, the pci-pci bridge controller can't set the
correct address range.
For example, when *lower_limit is 0xfd000000 and bar_size is
0x4000000, in the following code at arch/sh/drivers/pci/pci-auto.c,
0x0 is set in bar_value.
pciauto_setup_bars()
{
...
bar_value = ((*lower_limit - 1) & ~(bar_size - 1)) + bar_size;
...
*lower_limit = bar_value + bar_size;
}
As a result, 0x4000000 is set in *lower_limit, but this value is wrong.
The following patch avoids this problem by checking the range of the
value and refusing to update the BAR if the calculated value ends up
being bogus.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I forgot to do this when wiring up the syscall.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add the "wapf" param. This param allows to define the behavior
of the Fn F2 key (wlan switch).
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
Clean the write_status function, and implement special case with
a switch inside write_status. It also make sure bt and wl status
are right when booting with the hardware switch off.
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Len Brown <len.brown@intel.com>
This driver was removed a while ago by commit
099175c94a
However, it seems that pci2000.h wasn't properly eliminated, so remove
it now.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The failure to map user-space pages leads to scsi command leak. It can
happens mostly because of user-space daemon bugs (or OOM). This patch
makes tgt just notify a LLD of the failure with sense when
blk_rq_map_user() fails.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch simplify the way to notify LLDs of the command completion
and addresses the following sense buffer problems:
- can't handle both data and sense.
- forces user-space to use aligned sense buffer
tgt copies sense_data from userspace to cmnd->sense_buffer (if
necessary), maps user-space pages (if necessary) and then calls
host->transfer_response (host->transfer_data is removed).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
scsi tgt breaks up a command into multple scatterlists
if we cannot fit all the data in one. This was because
the block rq helpers did not support large requests and
because we can get a command of any old size so it is
hard to preallocate pages for scatterlist large enough
(we cannot really preallocate pages with the bio map
user path). In 2.6.20, we added large request support to
the block layer helper, blk_rq_map_user. And at LSF,
we talked about increasing SCSI_MAX_PHYS_SEGMENTS for
scsi tgt if we want to support really really :) large
(greater than 256 * PAGE_SIZE in the worst mapping case)
requests.
The only target currently implemented does not even support
the multiple scatterlists stuff and only supports smaller
requests, so this patch just coverts scsi tgt to use
blk_rq_map_user.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
People do not read the README and seem to like to
unselect the crc32c module even though iscsi_tcp selects
it for them. This patch spits a error that tells the user
that they really do need the module. Hopefully, we will
get fewer people asking about this now.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
For a while now, the block layer has seperated max sectors
and max hw sectors. Software iscsi has no limit so this patch
increases max hw sectors, so we can support large pass through
commands.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Dave Miller meantioned that the data buffer in a past
sense fixup patch was not gauranteed to be aligned
properly for ia64. This patch has libiscsi use get_unalinged
to make sure. There are a couple more places in the
digest handling we may need to do this, but we are in the middle
of fixing that code for big endien systems so just the sense
access is fixed here.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
qla4xxx and iscsi_tcp or iser could be creating
sessions at the same time, so make session_nr id
allocation atomic.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch renames DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH to avoid
confusion with the drivers default values (DEFAULT_MAX_RECV_DATA_SEGMENT_LENGTH
is the iscsi RFC specific default).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add missing additional sense code and provide pointer to upstream
reference (from Doug Gilbert).
Add missing const (from Michael Tokarev).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Convert the sd.c SCSI logging calls to scmd_printk()/sd_printk()
instead of plain printk().
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make SCSI disk printing more consistent:
- Define sd_printk(), sd_print_sense_hdr() and sd_print_result()
- Move relevant header bits into sd.h
- Remove all the legacy disk_name passing and use scsi_disk pointers
where possible
- Switch printk() lines to the new sd_ functions so that output is
consistent
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enhances SCSI error printing by:
- Making use of scsi_print_result() in the completion functions.
- Having scmd_printk() output the disk name (when applicable).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Clean up constants.c and make result printing more user friendly:
- Refactor the command and sense functions so that the actual
formatting can be called from the various helper functions with the
correct prefix.
- Replace scsi_print_hostbyte() and scsi_print_driverbyte() with
scsi_print_result() which is verbose when CONFIG_SCSI_CONSTANTS is
on.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recent alterations to the gdth_fill_raw_cmd() path no longer set the
sg_ranz field for zero transfer commands. However, this field is used
lower down in the function to initialise ha->cmd_len to the size of
the firmware packet. If this uninitialised field contains a bogus
value, ha->cmd_len can become much larger than the actual firmware
packet and end up oopsing in gdth_copy_cmd() as it tries to copy this
huge packet to the device (usually because it runs into an unallocated
page).
The fix is to initialise the sg_ranz field to zero at the start of
gdth_fill_raw_cmd().
Signed-off-by: Joerg Dorchain <joerg@dorchain.net>
Acked-by: "Leubner, Achim" <Achim_Leubner@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This fix's an oops during driver load time. mptsas_probe calls
mpt_attach(over in mptbase.c). Inside that call, we read some
manufacturing config pages to setup some defaults. While reading the
config pages, the firmware doesn't complete the reply in time, and we
have a timeout. The timeout results in hardreset handler being called.
The hardreset handler calls all the fusion upper layer driver reset
callback handlers. The mptsas_ioc_reset function is the callback
handler in mptsas.c. So where I'm getting to, is mptsas_ioc_reset is
getting called before scsi_host_alloc is called, and the pointer ioc->sh
is NULL as well as the hostdata.
Signed-off-by: Judith Lebzelter <judith@osdl.org>
Acked-by: "Moore, Eric" <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If a PCI error is detected that cannot be recovered from, there
will be a double call of lpfc_pci_remove_one(), with the second call
resulting in a null-pointer dereference. The first call occurs in
lpfc_io_error_detected(), and the second call during pci device
remove. This patch eliminates the first call; its un-needed.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Acked-by: James Smart <James.Smart@Emulex.Com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When a BIOS bug presents multiple APIC/MADTs,
Linux currently uses the 1st and ignores the 2nd.
But some machines work better if we use the 2nd.
http://bugzilla.kernel.org/show_bug.cgi?id=7465
Add a warning and boot parameter "acpi_apic_instance=2"
to allow parsing the 2nd.
No change to default behaviour in this patch.
Signed-off-by: Len Brown <len.brown@intel.com>
Delete apparently unused header file drivers/char/drm/via_mm.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The overflows could lead to the AGP aperture overlapping the framebuffer are in the card's address space when the latter is located at the very end of th 32 bit address space, which would result in a freeze on X server startup,
probably because the card read commands from the framebuffer instead of from AGP.
See http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=392915 .
Signed-off-by: Dave Airlie <airlied@linux.ie>
