ASoC: Updates for v6.8
This is a relatively quiet release, there's a lot of driver specific
changes and the usual high level of activity in the SOF core but the
one big core change was Mormioto-san's work to support more N:M
CPU:CODEC mapping cases. Highlights include:
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2.
- Support for falling back to older SOF IPC versions where firmware for
new versions is not available.
- Support for notification of control changes generated by SOF firmware
with IPC4.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases).
- ACPI parsing support for the ES83xx driver, reducing the number of
quirks neede for x86 systems.
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100.
- Removal of Freescale MPC8610 support, the SoC is no longer supported
by Linux.
The current code flow is:
1. snd_hdac_device_register()
2. set parameters needed by the hdac driver
3. request_codec_module()
the hdac driver is probed at this point
During boot the codec drivers are not loaded when the hdac device is
registered, it is going to be probed later when loading the codec module,
which point the parameters are set.
On module remove/insert
rmmod snd_sof_pci_intel_tgl
modprobe snd_sof_pci_intel_tgl
The codec module remains loaded and the driver will be probed when the
hdac device is created right away, before the parameters for the driver
has been configured:
1. snd_hdac_device_register()
the hdac driver is probed at this point
2. set parameters needed by the hdac driver
3. request_codec_module()
will be a NOP as the module is already loaded
Move the snd_hdac_device_register() later, to be done right before
requesting the codec module to make sure that the parameters are all set
before the device is created:
1. set parameters needed by the hdac driver
2. snd_hdac_device_register()
3. request_codec_module()
This way at the hdac driver probe all parameters will be set in all cases.
Link: https://github.com/thesofproject/linux/issues/4731
Fixes: a0575b4add ("ASoC: hdac_hda: Conditionally register dais for HDMI and Analog")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231207095425.19597-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/ZYvUIxtrqBQZbNlC@shine.dominikbrodowski.net
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218304
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current code flow is:
1. snd_hdac_device_register()
2. set parameters needed by the hdac driver
3. request_codec_module()
the hdac driver is probed at this point
During boot the codec drivers are not loaded when the hdac device is
registered, it is going to be probed later when loading the codec module,
which point the parameters are set.
On module remove/insert
rmmod snd_sof_pci_intel_tgl
modprobe snd_sof_pci_intel_tgl
The codec module remains loaded and the driver will be probed when the
hdac device is created right away, before the parameters for the driver
has been configured:
1. snd_hdac_device_register()
the hdac driver is probed at this point
2. set parameters needed by the hdac driver
3. request_codec_module()
will be a NOP as the module is already loaded
Move the snd_hdac_device_register() later, to be done right before
requesting the codec module to make sure that the parameters are all set
before the device is created:
1. set parameters needed by the hdac driver
2. snd_hdac_device_register()
3. request_codec_module()
This way at the hdac driver probe all parameters will be set in all cases.
Link: https://github.com/thesofproject/linux/issues/4731
Fixes: a0575b4add ("ASoC: hdac_hda: Conditionally register dais for HDMI and Analog")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231207095425.19597-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
ASoC: Updates for v6.7
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
[ the merge conflicts around SOF Intel HD-audio and CS35L41 subcodec
drivers are resolved here -- tiwai ]
In the existing IPC support, the reply to each IPC message is handled in
an IRQ thread. The assumption is that the IRQ thread is scheduled without
significant delays.
On an experimental (iow, buggy) kernel, the IRQ thread dealing with the
reply to the last IPC message before powering-down the DSP can be delayed
by several seconds. The IRQ thread will proceed with register accesses
after the DSP is powered-down which results in a kernel crash.
While the bug which causes the delay is not in the audio stack, we must
handle such cases with defensive programming to avoid such crashes.
Call synchronize_irq() before proceeding to power down the DSP to make
sure that no irq thread is pending execution.
Closes: https://github.com/thesofproject/linux/issues/4608
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231012191850.147140-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
The SOF platform drivers all use either sof_of_remove() or
sof_acpi_remove() which both return zero unconditionally. Change these
functions to return void and the drivers to use .remove_new(). There is
no semantical change.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20231009155945.285537-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
When a firmware crashes it creats a panic information into a telemetry
slot. The panic format is defined by Zephyr, includes stack and
additional information to help to identify the reason for the crash.
Part of the firmware exception handling the firmware also sends an
EXCEPTION_CAUGHT notification.
This series implements the kernel side handling of the exception: print
information into the kernel log export the whole telemetry slot to user
space for tools extract additional information from the panic dump.
There is a certain sequence needs to be followed when configuring the HDA
DMA in host and DSP.
The firmware provides a way to handle this two stage sequencing by
splitting the library loading into two stage:
1st stage: LOAD_LIBRARY_PREPARE message
the lib_id is 0, used to configure the DMA on DSP side
2nd stage: LOAD_LIBRARY message
both dma_id and lib_id is valid, used for the actual transfer of
the library
In case a firmware without support for this two stage loading is used then
the second stage message will trigger the loading and the first stage will
return with error, which is ignored by the kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Chao Song <chao.song@linux.intel.com>
Link: https://lore.kernel.org/r/20230915114018.1701-5-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns (or errors with CONFIG_WERROR):
sound/soc/sof/intel/hda.c:423:6: error: variable 'chip' is uninitialized when used here [-Werror,-Wuninitialized]
423 | if (chip && chip->check_sdw_wakeen_irq)
| ^~~~
sound/soc/sof/intel/hda.c:418:39: note: initialize the variable 'chip' to silence this warning
418 | const struct sof_intel_dsp_desc *chip;
| ^
| = NULL
1 error generated.
Add the missing initialization, following the pattern of the other irq
functions.
Fixes: 9362ab78f1 ("ASoC: SOF: Intel: add abstraction for SoundWire wake-ups")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230809-intel-hda-missing-chip-init-v1-1-61557ca6fa8a@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
This patchset first fixes a number of errors made in the hda-mlink
support, then adds Lunar Lake definitions. The main contribution is
the hda-dai changes where the HDaudio DMA is now used for SSP, DMIC
and SoundWire. In previous hardware the GPDMA (aka DesignWare) was
used and controlled by the audio firmware. The volume of code is
minimized with the abstraction added in previous kernel cycles.
Due to cross-dependencies between ASoC and SoundWire trees, the full
support for jack detection will be deferred to the next kernel
cycle. There's not much point to ask for a sync of the two trees to
support one patch for each tree - we are at -rc5 already.
