This change is needed to not fool drop monitor.
(perf record ... -e skb:kfree_skb )
Packets were properly sent and are consumed after TX completion.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on neighbors based on dpipe's host table
counter status. This patch also adds the ability for getting the counter
value, which will be used by the dpipe host table implementation in the
next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing support for neighbor
counters. The flow counter's type enum is used by many registers, yet,
until now it was used only by mgpc and thus it was private. This patch
updates the namespace for more generic usage.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing the ability to dump the
host table via dpipe, and to count the table size. The mlxsw's neighbor
representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work queues cannot be allocated when a mutex is held because the mutex
may be in use and that would make it sleep. Doing so generates the
following splat with 4.13+:
[ 19.513298] ======================================================
[ 19.513429] WARNING: possible circular locking dependency detected
[ 19.513557] 4.13.0-rc5+ #6 Not tainted
[ 19.513638] ------------------------------------------------------
[ 19.513767] cpuhp/0/12 is trying to acquire lock:
[ 19.513867] (&tz->lock){+.+.+.}, at: [<ffffffff924afebb>] thermal_zone_get_temp+0x5b/0xb0
[ 19.514047]
[ 19.514047] but task is already holding lock:
[ 19.514166] (cpuhp_state){+.+.+.}, at: [<ffffffff91cc4baa>] cpuhp_thread_fun+0x3a/0x210
[ 19.514338]
[ 19.514338] which lock already depends on the new lock.
This lock dependency already existed with previous kernel versions,
but it was not detected until commit 49dfe2a677 ("cpuhotplug: Link
lock stacks for hotplug callbacks") was introduced.
Reported-by: David Weinehall <david.weinehall@intel.com>
Reported-by: Jiri Kosina <jikos@kernel.org>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a flow table entry (fte) to a flow table (ft), we first
need to find its flow group (fg). Currently, this is done by
traversing a linear list of all flow groups in the flow table.
Furthermore, since multiple flow groups which correspond to the same
fte mask may exist in the same ft, we can't just stop at the first
match. Converting the linear list to rhltable in order to speed things
up.
The last four patches increases the steering rules update rate by a
factor of more than 7 (for insertion of 50K steering rules).
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When adding a flow table entry (fte) to a flow group (fg), we first
need to check whether this fte exist. In such a case we just merge
the destinations (if possible). Currently, this is done by traversing
the fte list available in a fg. This could take a lot of time when
using large flow groups. Speeding this up by using rhashtable, which
is much faster.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code stores fte_match_param in the software representation
of FTEs and FGs. fte_match_param contains a large reserved area at the
bottom of the struct. Since downstream patches are going to hash this
part, we would like to avoid doing so on a reserved part.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When allocating a flow table entry, we need to allocate a free index
in the flow group. Currently, this is done by traversing the existing
flow table entries in the flow group, until a free index is found.
Replacing this by using a ida, which allows us to find a free index
much faster.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix the following checkpatch warning in en_ethtool.c:
WARNING: suspect code indent for conditional statements (8, 9)
+ for (i = 0; i < NUM_PCIE_PERF_STALL_COUNTERS(priv); i++)
+ strcpy(data + (idx++) * ETH_GSTRING_LEN,
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The blank line should be after u32 val = ...
and not after __be32 __iomem *addr = ...
Fixes: ad5b39a95c ("net/mlx5: Add a blank line after declarations")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Joe Perches <joe@perches.com>
Stephen Rothwell reported quite a few conflicts in iwlwifi between
wireless-drivers and wireless-drivers-next. To avoid any problems later in
other trees merge w-d to w-d-next to fix those conflicts early.
Make these const as they are only stored in the const field of a
net_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ieee80211_ops are not supposed to change at runtime. All functions
working with ieee80211_ops provided by <net/mac80211.h> work with
const ieee80211_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Check memory allocation failure and return -ENOMEM in such a case, as
already done a few lines below.
As 'dev->tx_q' can be NULL, we also need to check for that in
'mt7601u_free_tx()', and return early.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a static checker fix. "cal_num" is 10. We're declaring the
tx_dt[] and rx_td[] arrays as 3 element arrays. The static checker
complains that we do:
tx_dt[cal] = (vdf_y[1]>>20)-(vdf_y[0]>>20);
"cal" is the iterator and it is in the 0-9 range so it looks like
we could corrupt memory.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactor code in order to avoid identical code for different branches.
This issue was detected with the help of Coccinelle.
Addresses-Coverity-ID: 1415177
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following commits:
commit c815fdebef ("wlcore: spi: Populate config firmware data")
commit d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Populated the nvs entry for wilink6 and wilink7 only while it is
still needed for wilink8 as well.
This broke user space backward compatibility when upgrading from older
kernels, as the alternate mac address would not be read from the nvs that
is present in the file system (lib/firmware/ti-connectivity/wl1271-nvs.bin)
causing mac address change of the wlan interface.
This patch fix this and update the structure field with the same default
nvs file name that has been used before.
In addition, some distros hold a default wl1271-nvs.bin in the file
system with a bogus mac address (deadbeef...) that overrides the mac
address that is stored inside the device.
Warn users about this bogus mac address and use the internal mac address
Fixes: c815fdebef ("wlcore: spi: Populate config firmware data")
Fixes: d776fc86b8 ("wlcore: sdio: Populate config firmware data")
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.14. Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
bnxt_hwrm_func_qcaps() is called during probe to get all device
resources and it also sets up the factory MAC address. The same function
is called when SRIOV is disabled to reclaim all resources. If
the MAC address has been overridden by a user administered MAC
address, calling this function will overwrite it.
Separate the logic that sets up the default MAC address into a new
function bnxt_init_mac_addr() that is only called during probe time.
Fixes: 4a21b49b34 ("bnxt_en: Improve VF resource accounting.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take back ownership of the MSIX vectors when unregistering the device
from bnxt_re.
Fixes: a588e4580a ("bnxt_en: Add interface to support RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the number of TX rings is changed in bnxt_setup_tc(), we need to
include the XDP rings in the total TX ring count.
Fixes: 3841340627 ("bnxt_en: Add support for XDP_TX action.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX completion may happen any time after HW queue was kicked.
We can't access the skb afterwards. Move the time stamping
before ringing the doorbell.
Fixes: 4c3523623d ("net: add driver for Netronome NFP4000/NFP6000 NIC VFs")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions set_ctrl0 and set_ctrl1 are local to the source and do
not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'set_ctrl0' was not declared. Should it be static?
symbol 'set_ctrl1' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If action is gact goto_chain, offload it to HW by jumping to another
ruleset.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to lookup ruleset in order to offload goto_chain termination
action. This patch adds it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For goto_chain action we need to know group_id of a ruleset to jump to.
Provide infrastructure in order to get it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflect chain index coming down from TC core and create a ruleset per
chain. Note that only chain 0, being the implicit chain, is bound to the
device for processing. The rest of chains have to be "jumped-to" by
actions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch uses the tso API to implement the tso functionality in Marvell
PPv2 driver.
Using iperf and 10G ports, using TSO shows a significant performance
improvement by a factor 2 to reach around 9.5Gbps in TX; as well as a
significant CPU usage drop (from 25% to 15%).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The txq size is defined by MVPP2_AGGR_TXQ_SIZE, which is sometime not
used directly but through variables. As it is a fixed value use the
define everywhere in the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver receives a muxed frame, but it can't find the representor
netdev it is destined to it will try to "drop" that frame, i.e. reuse
the buffer. The issue is that the replacement buffer has already been
allocated at this point, and reusing the buffer from received frame
will leak it. Change the code to put the new buffer on the ring
earlier and not reuse the old buffer (make the buffer parameter
to nfp_net_rx_drop() a NULL).
Fixes: 91bf82ca9e ("nfp: add support for tx/rx with metadata portid")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
App start/stop callbacks can perform application initialization.
Unfortunately, flower app started using them for creating and
destroying representors. This can lead to a situation where
lower vNIC netdev is destroyed while representors still try
to pass traffic. This will most likely lead to a NULL-dereference
on the lower netdev TX path.
Move the start/stop callbacks, so that representors are created/
destroyed when vNICs are fully initialized.
Fixes: 5de73ee467 ("nfp: general representor implementation")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling SR-IOV VFs will cause the PCI subsystem to schedule a
work and flush its workqueue. Since the nfp driver schedules its
own work we can't enable VFs while holding driver load. Commit
6d48ceb27a ("nfp: allocate a private workqueue for driver work")
tried to avoid this deadlock by creating a separate workqueue.
Unfortunately, due to the architecture of workqueue subsystem this
does not guarantee a separate thread of execution. Luckily
we can simply take pci_enable_sriov() from under the driver lock.
Take pci_disable_sriov() from under the lock too for symmetry.
Fixes: 6d48ceb27a ("nfp: allocate a private workqueue for driver work")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NIC firmware, the 1-bit flag indicating "firmware is loaded" moved
from SLI_SCRATCH_1 to SLI_SCRATCH_2 (these are Octeon general-purpose
scratch registers). Make the PF driver conform to this change.
Remove code that sets the "firmware is loaded" flag because it's now the
firmware's job to do that.
In the code that detects whether or not the firmware is loaded, don't just
rely on checking the "firmware is loaded" flag because that may cause a
rare false negative. Add code that deduces whether or not the firmware is
loaded; that will never give a false negative.
Also bump up driver version to match newer NIC firmware.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MII/GMII/SGMII in the Altera SoC, the phy needs to be
wired through the FPGA. To ensure correct behavior, the appropriate
bit in the System Manager FPGA Interface Group register needs to be
set.
Signed-off-by: Stephan Gatzka <stephan.gatzka@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Junote Cai reported that he was not able to get a DSA setup involving the
Freescale DPAA/FMAN driver to work and narrowed it down to
of_find_net_device_by_node(). This function requires the network device's
device reference to be correctly set which is the case here, though we have
lost any device_node association there.
The problem is that dpaa_eth_add_device() allocates a "dpaa-ethernet" platform
device, and later on dpaa_eth_probe() is called but SET_NETDEV_DEV() won't be
propagating &pdev->dev.of_node properly. Fix this by inherenting both the parent
device and the of_node when dpaa_eth_add_device() creates the platform device.
Fixes: 3933961682 ("fsl/fman: Add FMan MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zorro_device_id are not supposed to change at runtime. All functions
working with zorro_device_id provided by <linux/zorro.h> work with
const zorro_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
