In addition to these changes I doubt the 'volatile' on all the ticket
lock asm()-s are really necessary.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some architectures have moved the asm/ into arch/ and some have not.
This patch checks for a.out.h and kvh.h in both places before exporting
the corresponding file from linux/
[dwmw2: simplified a little]
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is a ordering related problem with clockevents code, due to which
clockevents_register_device() called after tickless/highres switch
will not work. The new clockevent ends up with clockevents_handle_noop as
event handler, resulting in no timer activity.
The problematic path seems to be
* old device already has hrtimer_interrupt as the event_handler
* new clockevent device registers with a higher rating
* tick_check_new_device() is called
* clockevents_exchange_device() gets called
* old->event_handler is set to clockevents_handle_noop
* tick_setup_device() is called for the new device
* which sets new->event_handler using the old->event_handler which is noop.
Change the ordering so that new device inherits the proper handler.
This does not have any issue in normal case as most likely all the clockevent
devices are setup before the highres switch. But, can potentially be affecting
some corner case where HPET force detect happens after the highres switch.
This was a problem with HPET in MSI mode code that we have been experimenting
with.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
64-bit has X86_HT set too, so use that instead of SMP.
This also removes a include/asm-x86/processor.h ifdef.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Which top-level unit's SMI interface to use should be a property of
the top-level unit, not of the individual ports. This patch moves the
->shared_smi pointer from the per-port platform data to the global
platform data.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Simplify receive and transmit queue handling by requiring the set
of queue numbers to be contiguous starting from zero.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Adjust various debug outputs to use the new *_BUF macro variants for
correct output of v4/v6 addresses.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Convert functions for looking up destinations (real servers) to support
IPv6 services/dests.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add xmit functions for IPv6. Also add the already needed __ip_vs_get_out_rt_v6()
to ip_vs_core.c. Bind the new xmit functions to v6 connections.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Extend functions for getting/creating connections and connection
templates for IPv6 support and fix the callers.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Extend protocol DNAT/SNAT and state handlers to work with IPv6. Also
change/introduce new checksumming helper functions for this.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add 'af' arguments to conn_schedule(), conn_in_get(), conn_out_get() and
csum_check() function pointers in struct ip_vs_protocol. Extend the
respective functions for TCP, UDP, AH and ESP and adjust the callers.
The changes in the callers need to be somewhat extensive, since they now
need to pass a filled out struct ip_vs_iphdr * to the modified functions
instead of a struct iphdr *.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add 'supports_ipv6' flag to struct ip_vs_scheduler to indicate whether a
scheduler supports IPv6. Set the flag to 1 in schedulers that work with
IPv6, 0 otherwise. This flag is checked in a later patch while trying to
add a service with a specific scheduler. Adjust debug in v6-supporting
schedulers to work with both address families.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add support for selecting services based on their address family to
ip_vs_service_get() and adjust the callers.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add extended internal versions of struct ip_vs_service_user and struct
ip_vs_dest_user (the originals can't be modified as they are part
of the old sockopt interface). Adjust ip_vs_ctl.c to work with the new
data structures and add some minor AF-awareness.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add some debugging macros that allow conditional output of either v4 or v6
addresses, depending on an 'af' parameter. This is done by creating a
temporary string buffer in an outer debug macro and writing addresses'
string representations into it from another macro which can only be used
when inside the outer one.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Add a struct ip_vs_iphdr for easier handling of common v4 and v6 header
fields in the same code path. ip_vs_fill_iphdr() helps to fill this struct
from an IPv4 or IPv6 header. Add further helper functions for copying and
comparing addresses.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Introduce new 'af' fields into IPVS data structures for specifying an
entry's address family. Convert IP addresses to be of type union
nf_inet_addr.
Signed-off-by: Julius Volz <juliusv@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
1. add extended_cpuid_level for 32bit
2. add generic_identify for 64bit
3. add early_identify_cpu for 32bit
4. early_identify_cpu not be called by identify_cpu
5. remove early in get_cpu_vendor for 32bit
6. add get_cpu_cap
7. add cpu_detect for 64bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
add reserve_region_with_split() to not lose e820 reserved entries if
they overlap with existing IO regions:
with test case by extend 0xe0000000 - 0xeffffff to 0xdd800000 -
we get:
e0000000-efffffff : PCI MMCONFIG 0
e0000000-efffffff : reserved
and in /proc/iomem we get:
found conflict for reserved [dd800000, efffffff], try to reserve with split
__reserve_region_with_split: (PCI Bus #80) [dd000000, ddffffff], res: (reserved) [dd800000, efffffff]
__reserve_region_with_split: (PCI Bus #00) [de000000, dfffffff], res: (reserved) [de000000, efffffff]
initcall pci_subsys_init+0x0/0x121 returned 0 after 381 msecs
in dmesg
various fixes and improvements suggested by Linus.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
so could let BAR res register at first, or even pnp.
v2: insert e820 reserve resources before pnp_system_init
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
At the moment, 64-bit platforms (other than Alpha) are all redefining
things for themselves instead of using <asm-generic/statfs.h>.
As is ARM, since it has special requirements w.r.t. padding.
Make <asm-generic/statfs.h> more generic, and they can use it directly.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Also, stop looking at the NAND controller (0x4100) and checking the
device class. For a while during development, all three functions on the
chip had the same ID. We made them fix that fairly promptly, and we can
forget about it now.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This patch adds a generic infrastructure for policy-based dequeueing of
TX packets and provides two policies:
* a simple FIFO policy (which is the default) and
* a priority based policy (set via socket options).
Both policies honour the tx_qlen sysctl for the maximum size of the write
queue (can be overridden via socket options).
The priority policy uses skb->priority internally to assign an u32 priority
identifier, using the same ranking as SO_PRIORITY. The skb->priority field
is set to 0 when the packet leaves DCCP. The priority is supplied as ancillary
data using cmsg(3), the patch also provides the requisite parsing routines.
Signed-off-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch consolidates the code common to TCP and CCID-2:
* TCP uses RFC 3390 in a packet-oriented manner (tcp_input.c) and
* CCID-2 uses RFC 3390 in packet-oriented manner (RFC 4341).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This extends the packet dequeuing interface of dccp_write_xmit() to allow
1. CCIDs to take care of timing when the next packet may be sent;
2. delayed sending (as before, with an inter-packet gap up to 65.535 seconds).
The main purpose is to take CCID2 out of its polling mode (when it is network-
limited, it tries every millisecond to send, without interruption).
The interface can also be used to support other CCIDs.
The mode of operation for (2) is as follows:
* new packet is enqueued via dccp_sendmsg() => dccp_write_xmit(),
* ccid_hc_tx_send_packet() detects that it may not send (e.g. window full),
* it signals this condition via `CCID_PACKET_WILL_DEQUEUE_LATER',
* dccp_write_xmit() returns without further action;
* after some time the wait-condition for CCID becomes true,
* that CCID schedules the tasklet,
* tasklet function calls ccid_hc_tx_send_packet() via dccp_write_xmit(),
* since the wait-condition is now true, ccid_hc_tx_packet() returns "send now",
* packet is sent, and possibly more (since dccp_write_xmit() loops).
Code reuse: the taskled function calls dccp_write_xmit(), the timer function
reduces to a wrapper around the same code.
If the tasklet finds that the socket is locked, it re-schedules the tasklet
function (not the tasklet) after one jiffy.
Changed DCCP_BUG to dccp_pr_debug when transmit_skb returns an error (e.g. when a
local qdisc is used, NET_XMIT_DROP=1 can be returned for many packets).
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The problem with Ack Vectors is that
i) their length is variable and can in principle grow quite large,
ii) it is hard to predict exactly how large they will be.
Due to the second point it seems not a good idea to reduce the MPS; in
particular when on average there is enough room for the Ack Vector and an
increase in length is momentarily due to some burst loss, after which the
Ack Vector returns to its normal/average length.
The solution taken by this patch is to subtract a minimum-expected Ack Vector
length from the MPS (previous patch), and to defer any larger Ack Vectors onto
a separate Sync - but only if indeed there is no space left on the skb.
This patch provides the infrastructure to schedule Sync-packets for transporting
(urgent) out-of-band data. Its signalling is quicker than scheduling an Ack, since
it does not need to wait for new application data.
It can thus serve other parts of the DCCP code as well.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
The constants DCCPO_{MIN,MAX}_CCID_SPECIFIC are nowhere used in the code, but
instead for the CCID-specific options numbers are used.
This patch unifies the use of CCID-specific option numbers, by adding symbolic
names reflecting the definitions in RFC 4340, 10.3.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
This patch takes care of initialising and type-checking sysctls related to
feature negotiation. Type checking is important since some of the sysctls
now directly act on the feature-negotiation process.
The sysctls are initialised with the known default values for each feature.
For the type-checking the value constraints from RFC 4340 are used:
* Sequence Window uses the specified Wmin=32, the maximum is ulong (4 bytes),
tested and confirmed that it works up to 4294967295 - for Gbps speed;
* Ack Ratio is between 0 .. 0xffff (2-byte unsigned integer);
* CCIDs are between 0 .. 255;
* request_retries, retries1, retries2 also between 0..255 for good measure;
* tx_qlen is checked to be non-negative;
* sync_ratelimit remains as before.
Further changes:
----------------
Performed s@sysctl_dccp_feat@sysctl_dccp@g since the sysctls are now in feat.c.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This adds full support for local/remote Sequence Window feature, from which the
* sequence-number-validity (W) and
* acknowledgment-number-validity (W') windows
derive as specified in RFC 4340, 7.5.3.
Specifically, the following changes are introduced:
* integrated new socket fields into dccp_sk;
* updated the update_gsr/gss routines with regard to these fields;
* updated handler code: the Sequence Window feature is located at the TX side,
so the local feature is meant if the handler-rx flag is false;
* the initialisation of `rcv_wnd' in reqsk is removed, since
- rcv_wnd is not used by the code anywhere;
- sequence number checks are not done in the LISTEN state (cf. 7.5.3);
- dccp_check_req checks the Ack number validity more rigorously;
* the `struct dccp_minisock' became empty and is now removed.
Until the handshake completes with activating negotiated values, the local/remote
Sequence-Window values are undefined and thus can not reliably be estimated.
This issue is addressed in a separate patch.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This initialises feature negotiation from two tables, which are initialised
from sysctls.
As a novel feature, specifics of the implementation (e.g. currently short
seqnos and ECN are not supported) are advertised for robustness.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
This removes the use of the sysctl and the minisock variable for the Send Ack
Vector feature, which is now handled fully dynamically via feature negotiation;
i.e. when CCID2 is enabled, Ack Vectors are automatically enabled (as per
RFC 4341, 4.).
Using a sysctl in parallel to this implementation would open the door to
crashes, since much of the code relies on tests of the boolean minisock /
sysctl variable. Thus, this patch replaces all tests of type
if (dccp_msk(sk)->dccpms_send_ack_vector)
/* ... */
with
if (dp->dccps_hc_rx_ackvec != NULL)
/* ... */
The dccps_hc_rx_ackvec is allocated by the dccp_hdlr_ackvec() when feature
negotiation concluded that Ack Vectors are to be used on the half-connection.
Otherwise, it is NULL (due to dccp_init_sock/dccp_create_openreq_child),
so that the test is a valid one.
The activation handler for Ack Vectors is called as soon as the feature
negotiation has concluded at the
* server when the Ack marking the transition RESPOND => OPEN arrives;
* client after it has sent its ACK, marking the transition REQUEST => PARTOPEN.
Adding the sequence number of the Response packet to the Ack Vector has been
removed, since
(a) connection establishment implies that the Response has been received;
(b) the CCIDs only look at packets received in the (PART)OPEN state, i.e.
this entry will always be ignored;
(c) it can not be used for anything useful - to detect loss for instance, only
packets received after the loss can serve as pseudo-dupacks.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
Updating the NDP count feature is handled automatically now:
* for CCID-2 it is disabled, since the code does not use NDP counts;
* for CCID-3 it is enabled, as NDP counts are used to determine loss lengths.
Allowing the user to change NDP values leads to unpredictable and failing
behaviour, since it is then possible to disable NDP counts even when they
are needed (e.g. in CCID-3).
This means that only those user settings are sensible that agree with the
values for Send NDP Count implied by the choice of CCID. But those settings
are already activated by the feature negotiation (CCID dependency tracking),
hence this form of support is redundant.
At startup the initialisation of the NDP count feature is with the default
value of 0, which is done implicitly by the zeroing-out of the socket when
it is allocated. If the choice of CCID or feature negotiation enables NDP
count, this will then be updated via the NDP activation handler.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: Ian McDonald <ian.mcdonald@jandi.co.nz>
