Use threaded interrupts for all rt2x00 PCI devices.
This has several generic advantages:
- Reduce the time we spend in hard irq context
- Use non-atmic mac80211 functions for rx/tx
Furthermore implementing broad- and multicast buffering will be
much easier in process context while maintaining low latency and
updating the beacon just before transmission (pre tbtt interrupt)
can also be done in process context.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_write_beacon is the only function which uses
EXPORT_SYMBOL instead of EXPORT_SYMBOL_GPL. All symbols
in rt2x00 should however use the GPL restricted export.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implement watchdog monitoring for USB devices (PCI support can
be added later). This will determine if URBs being uploaded to
the hardware are actually returning. Both rt2500usb and rt2800usb
have shown that URBs being uploaded can remain hanging without
being released by the hardware.
By using this watchdog, a queue can be reset when this occurs.
For rt2800usb it has been tested that the connection is preserved
even though this interruption.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently vgc_level_reg and vgc_level are equal to eachother,
while the purpose of vgc_level_reg is the value last written
to the register and is remembered through link tuning resets.
The vgc_level is the currently active level, which is
reset during link tuning resets.
The usage of these variables depends on the drivers, some drivers
need both, while others need only one of the two.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While scanning the link tuner must be disabled. Otherwise
it will interfere with receiving all beacons for each channel
due to changing sensitivity levels.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename CONFIG_DISABLE_LINK_TUNING to DRIVER_SUPPORT_LINK_TUNING
Link tuning support is not only based on EEPROM decisions, but
also if the device actually supports it.
Currently only rt2500usb doesn't support link tuning because
of hardware problems. But rt2800usb is also suspected of having
problems with link tuning.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RSSI values in the RXWI descriptor aren't true RSSI
values. Instead they are more like the AGC values similar
to rt61pci. And as such, it needs the same conversion
before it can be passed to rt2x00lib/mac80211.
This requires the struct queue_entry to be passed to
rt2800_process_rxwi rather then the skb structure which
is contained in the queue_entry. This is required to
obtain the lna_gain information from the rt2x00_dev structure.
This fixes connection problems when using wpa_supplicant
which would try to connect to the worst AP's rather then the
best ones.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the txpower per rate by the approriate values in the eeprom.
This avoids too high txpower values resulting in bad tx performance.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In hostap_add_interface() we do:
sprintf(dev->name, "%s%s", prefix, name);
dev->name has IFNAMSIZ (16) characters.
prefix is local->dev->name.
name is "wds%d"
strlen() returns the number of characters in the string not counting the
NULL so if we have a string with 11 characters we get "12345678901wds%d"
which is 16 characters and a NULL so we're past the end of the array.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This test is off by one because strlen() doesn't include the NULL
terminator.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes __attribute__ ((packed)) annotations to __packed in wl1271
code that was introduced in a recent patch in wireless-testing.
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Existing "ethtool -s ethX wol X" command configures hostsleep
parameters, but those are activated only during suspend/resume,
there is no way to configure host sleep without actual suspend.
This patch adds debugfs command to enable/disable host sleep based on
already configured host sleep parameters using wol command.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since mac80211/drivers are no longer
fully in charge of keeping track of the
auth status, trying to make them do so will
fail. Instead of warning and reporting the
deauthentication to userspace, cfg80211 must
simply ignore it so that spurious
deauthentications, e.g. before starting
authentication, aren't seen by userspace as
actual deauthentications.
Cc: stable@kernel.org
Reported-by: Paul Stewart <pstew@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CodingStyle cleanups
EXPORT_SYMBOL should immediately follow the symbol declaration.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the main loop in acpi_ev_initialize_gpe_block() by
rearranging code and removing the "enabled" label that is not
necessary any more.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Make acpi_gpe_wakeup() return error code for GPEs whose
ACPI_GPE_CAN_WAKE flag is not set. This way acpi_gpe_wakeup() will
only wake for the GPEs reported by the host OS as "wakeup" ones with
the help of acpi_gpe_can_wake().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently, during initialization ACPICA walks the entire ACPI
namespace in search of any device objects with assciated _PRW
methods. All of the _PRW methods found are executed in the process
to extract the GPE information returned by them, so that the GPEs in
question can be marked as "able to wakeup" (more precisely, the
ACPI_GPE_CAN_WAKE flag is set for them). The only purpose of this
exercise is to avoid enabling the CAN_WAKE GPEs automatically, even
if there are _Lxx/_Exx methods associated with them. However, it is
both costly and unnecessary, because the host OS has to execute the
_PRW methods anyway to check which devices can wake up the system
from sleep states. Moreover, it then uses full information
returned by _PRW, including the GPE information, so it can take care
of disabling the GPEs if necessary.
Remove the code that walks the namespace and executes _PRW from
ACPICA and modify comments to reflect that change. Make
acpi_bus_set_run_wake_flags() disable GPEs for wakeup devices
so that they don't cause spurious wakeup events to be signaled.
This not only reduces the complexity of the ACPICA initialization
code, but in some cases it should reduce the kernel boot time as
well.
Unfortunately, for this purpose we need a new ACPICA function,
acpi_gpe_can_wake(), to be called by the host OS in order to disable
the GPEs that can wake up the system and were previously enabled by
acpi_ev_initialize_gpe_block() or acpi_ev_update_gpes() (such a GPE
should be disabled only once, because the initialization code enables
it only once, but it may be pointed to by _PRW for multiple devices
and that's why the additional function is necessary).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When we check if a GPE can be used for runtime signaling, we only
search the FADT GPE blocks, which is incorrect, becuase the GPE
may be located elsewhere. We really should be using the GPE device
information previously returned by _PRW here, so make that happen.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The commit 5d554a7bb0 (ACPI: processor: add internal
processor_physically_present()) is broken on uniprocessor (UP)
configurations, as acpi_get_cpuid() will always return -1.
We use the value of num_possible_cpus() to tell us whether we got
an invalid cpuid from acpi_get_cpuid() in the SMP case, or if
instead, we are UP, in which case num_possible_cpus() is #defined
as 1.
We use num_possible_cpus() instead of num_online_cpus() to
protect ourselves against the scenario of CPU hotplug, and we've
taken down all the CPUs except one.
Thanks to Jan Pogadl for initial report and analysis and Chen
Gong for review.
https://bugzilla.kernel.org/show_bug.cgi?id=16357
Reported-by: Jan Pogadl <pogadl.jan@googlemail.com>:
Reviewed-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Hmmm. There are still people who have their editor setup with tabwidth 4.
Some of the entries were added with tabwidth 4, and for these people
the lineup looks OK. But in the Linux kernel source we use tabwidth 8.
This patch repairs that whitespace so that the number align properly.
Signed-off-by: Kees Bakker <kees.bakker@xs4all.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As our device may be hot-unplugged and framebuffer cannot handle
this case by itself we need to keep track of usage count so as
to release fb_info and framebuffer memory only after the last user
has closed framebuffer.
We need to do the freeing in a scheduled work as fb_release()
is called with fb_info lock held.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reallocating memory in depth change does not work well if some
userspace application has mmapped() the framebuffer as that mapping
does not get adjusted (thus application continues to write to old
buffer).
In addition doing deferred_io_cleanup() and init() inside of set_par()
tends to deadlock with fbcon's flashing cursor.
Avoid all this by allocating a buffer that can hold 8bpp framebuffer
and just use 1/8 of it while running at 1bpp.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a minimal palette so fbcon does not try to dereference
a NULL point when fb is set to 8bpp.
fbcon stores pixels the other way around in bytes for 1bpp
than intially implemented, correct this.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This moves the lock_kernel() call from soundcore_open
to the individual OSS device drivers, where we can deal
with it one driver at a time if needed, or just kill
off the drivers.
All core components in ALSA already provide
adequate locking in their open()-functions
and do not require the big kernel lock, so
there is no need to add the BKL there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correctly configure bidirectional pins when resuming; do not power down
widgets when they are needed for Smart5.1 output; and on 3-jack boards,
create the streams and controls needed for six channels.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reported-and-tested-by: Viliam Kubis <viliam.kubis@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As per-stream volume controls, the DXS controls are not intended to
adjust the overall sound level and so are initialized every time
a stream is opened. However, there are special situations where one
wants to reduce the overall volume in the digital domain, i.e., before
the AC'97 codec's PCM volume control. To allow this, add a module
parameter that sets the initial DXS volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Soeren D. Schulze <soeren.d.schulze@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Userspace filesystem can request data to be retrieved from the inode's
mapping. This request is synchronous and the retrieved data is queued
as a new request. If the write to the fuse device returns an error
then the retrieve request was not completed and a reply will not be
sent.
Only present pages are returned in the retrieve reply. Retrieving
stops when it finds a non-present page and only data prior to that is
returned.
This request doesn't change the dirty state of pages.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Userspace filesystem can request data to be stored in the inode's
mapping. This request is synchronous and has no reply. If the write
to the fuse device returns an error then the store request was not
fully completed (but may have updated some pages).
If the stored data overflows the current file size, then the size is
extended, similarly to a write(2) on the filesystem.
Pages which have been completely stored are marked uptodate.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Don't use atomic kmap for mapping userspace buffers in device
read/write/splice.
This is necessary because the next patch (adding store notify)
requires that caller of fuse_copy_page() may sleep between
invocations. The simplest way to ensure this is to change the atomic
kmaps to non-atomic ones.
Thankfully architectures where kmap() is not a no-op are going out of
fashion, so we can ignore the (probably negligible) performance impact
of this change.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
As long as the zImage is placed within the 128MB range from the start of
memory, ZRELADDR (Address where the decompressed kernel will be placed,
usually == PHYS_OFFSET + TEXT_OFFSET) can be determined at run-time by
masking PC with 0xf80000000.
Running through all the Makefile.boot, all those zreladdr-y
addresses == 0x[0-f][08]00_0000 + TEXT_OFFSET can be determined at
run-time.
Option CONFIG_AUTO_ZRELADDR and CONFIG_ZRELADDR are introduced,
CONFIG_ZRELADDR _must_ be explicitly specified if:
- ((zreladdr-y - TEXT_OFFSET) & ~0xf8000000) != 0, which means
masking PC with 0xf8000000 will result in an incorrect address.
Currently this is only a problem on u300.
- or the assumption of the zImage being loaded by the bootloader within
the first 128MB of RAM is incorrect
- or when ZBOOT_ROM is used, where the above assumption is usually wrong.
[ukleinek: changed mask from 0xf0000000 to 0xf8000000 for mx1 and shark
+ some review fixes from the mailing list]
Original-Idea-and-Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Do not call free_irq() if request_irq() failed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() is called both in net_close() and cleanup_card(). Since it
is requested in at1700_probe1(), leave free_irq() only in cleanup_card()
for balance.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few registers have side effects on reads, eg FIFO pointers that
auto advance or mailboxes which change ownership when read. They are
unsafe to read so exclude them from ethtool register dumps.
Bump ethtool_regs.version to indicate the changed register set.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge error.
See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_rxnfc, get_rxfh_indir, and set_rxfh_indir ethtool
methods for user manipulation of the RSS table. Besides the methods
themselves the rest of the changes here store, initialize, and write
the table contents.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are two copies of some resource freeing code, turn it into
a function and call it.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to settle on the kind of interrupts we'll be using, a choice that
also impacts the number of queues, before registering and making visible
the net_devices. Move the relevant code up a bit.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following checkpatch errors:
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: do not use assignment in if condition
+ if ((mss = skb_shinfo(skb)->gso_size) != 0) {
ERROR: space prohibited after that '!' (ctx:BxW)
+ if (! netif_carrier_ok(tp->dev) &&
^
ERROR: space required after that ',' (ctx:VxV)
+#define GET_REG32_LOOP(base,len) \
^
ERROR: "(foo*)" should be "(foo *)"
+ memcpy(data, ((char*)&val) + b_offset, b_count);
ERROR: do not use assignment in if condition
+ if ((err = tg3_do_mem_test(tp, mem_tbl[i].offset,
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reverts commit 52cdf8526f,
entitled "tg3: Prevent a PCIe tx glitch". The problem does not have
any visible side-effects and happens too early for the driver to do
anything about it. The proper place for this code is within the
device's bootcode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the code so that the driver version can be reported
to the firmware in addition to the current use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 is coded to refuse to attach to 5717 serdes devices. Now that the
hardware is better supported, we can relax this restriction. This patch
also fixes a recently introduced bug which will cause serdes parallel
detection not to work with 5780 class devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3_start_xmit_dma_bug() function was missing code to process IPv6
TSO packets. This patch adds the missing support.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
