In OMAP4, there is only one irq line for TX and RX paths. Use
the correct irq line to avoid errors at runtime.
Also, request irq line only once (instead of requesting for TX
and RX).
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When ever driver changes the device state, it should write
pci-func number and timestamp in debug registers.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LRO ring, cut-thru mode and specific fw version are not
valid to Qlogic CNA device.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Window register is not per pci-func, so caching can
result in expected result.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI_MODE, CAPABILITIES_FW and SCRATCHPAD registers are obsolete.
Driver should not use them.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before going for recovery, every pci-func should check fw state,
irrespective of device state. This to avoid unnecssary sending
of command for ctx destroy.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating memory can fail, and since we have the memory we need
in sky2_resume when sky2_suspend is called, just stop the hardware
without freeing the memory it's using.
This avoids the possibility of failing because we can't allocate
memory in sky2_resume(), and allows sharing code with sky2_restart().
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code to bring down all sky2 interfaces and bring it up
again can be reused in sky2_suspend and sky2_resume.
Factor the code to bring the interfaces down into
sky2_all_down and the up code into sky2_all_up.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Interrupts should be masked, then synchronized, and
finally NAPI should be disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_stop_queue does not ensure all in-progress transmits are complete,
so use netif_tx_disable() instead.
Secondly, make sure NAPI polls are disabled before stopping the tx queue,
otherwise sky2_status_intr might trigger a TX queue wakeup between when
we stop the queue and NAPI is disabled.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to be an off-by-1 defect in the maximum packet size
copied when copybreak is speified in these modules.
The copybreak module params are specified as:
"Maximum size of packet that is copied to a new buffer on receive"
The tests are changed from "< copybreak" to "<= copybreak"
and moved into new static functions for readability.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the cleanup pass after the removal of e1000e hardware from e1000 some
parameters were missed. Remove them because it is just dead code.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding more than 14 mac-vlan adapters on e1000 the driver
would fire a WARN_ON when adding the 15th. The WARN_ON in this
case is completely un-necessary, as the code below the WARN_ON is
directly handling the value the WARN_ON triggered on.
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Redirecting directly to lsm, here's the patch discussed on lkml:
http://lkml.org/lkml/2010/4/22/219
The mmap_min_addr value is useful information for an admin to see without
being root ("is my system vulnerable to kernel NULL pointer attacks?") and
its setting is trivially easy for an attacker to determine by calling
mmap() in PAGE_SIZE increments starting at 0, so trying to keep it private
has no value.
Only require CAP_SYS_RAWIO if changing the value, not reading it.
Comment from Serge :
Me, I like to write my passwords with light blue pen on dark blue
paper, pasted on my window - if you're going to get my password, you're
gonna get a headache.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
(cherry picked from commit 822cceec72)
Doh. Pointed out by Guillaume LECERF <glecerf@gmail.com> since I managed
to miss it in my test builds. S'what I get for hacking at 2am, I suppose.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This rejects unaligned device virtual address('da') and physical
address('pa') and informs error to caller when a page table entry is
set. Otherwise, a wrong address can be used by IO device.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>
Searching avaialable spaces should be stopped as soon as it turns out
that there's no possibility with the rest of it.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Inserting a gap page between IOVMAs could detect an override on other
IOVMA with iommu fault. This was originally suggested by Sakari Ailus
and based on the work and comment by David Cohen.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: David Cohen <david.cohen@nokia.com>
Cc: Sakari Ailus <Sakari.Ailus@nokia.com>
This CONFIG_OMAP_IOMMU_DEBUG option cannot be selected because it's
not visible on menu. Make this option selectable.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There are some places to scan iotlb entries. This iteration macro
could make these code a bit simpler with proceeding iotlb entries
transparently.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Tested-by: Hari Kanigeri <h-kanigeri2@ti.com>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch includes changes to omap3-iommu.c file to make it generic
for all OMAPs. Renamed omap3-iommu.c to omap-iommu.c
[Hiroshi DOYU: Remove unnecessary "iommu-y" in Makefile]
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newer assemblers support the .cfi_sections directive so we can put
the CFI from .S files into the .debug_frame section that is preserved
in unstripped vmlinux and in separate debuginfo, rather than the
.eh_frame section that is now discarded by vmlinux.lds.S.
Signed-off-by: Roland McGrath <roland@redhat.com>
LKML-Reference: <20100514044303.A6FE7400BE@magilla.sf.frob.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use the resource_size function instead of manually calculating the
resource size. This reduces the chance of introducing off-by-one errors.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When we build with ftrace enabled its possible that loadcam_entry would
have used the stack pointer (even though the code doesn't need it). We
call loadcam_entry in __secondary_start before the stack is setup. To
ensure that loadcam_entry doesn't use the stack pointer the easiest
solution is to just have it in asm code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the following MAC functions are moved from 82598 & 82599 specific
hardware files to common.[ch] to accommodate new silicon changes. Also
fixed some white space issues
* get_san_mac_addr, check_link, set_vmdq, clear_vmdq, clear_vfta,
* set_vfta, fc_enable, init_uta_tables
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't use zero magic "bad" value to check if IXGBE_RSC_CB(skb)->dma
is valid. It is only valid in x86/arm/m68k/alpha architectures and in
spark, powerPC and other architectures it should be ~0. As per
Benjamin Herrenschmidt feedback use a bool flag to decide if
the packet unmapping is delayed in hardware RSC till EOP is reached
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce uc_set_promisc flag to fix enabling of promisc mode
when exceeding the number of supported RAR entries.
Issue discovered by Ben Greear when using mac-vlans.
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function cleans up after ext4_mb_load_buddy(), so the renaming
makes the code clearer.
Signed-off-by: Jing Zhang <zj.barak@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This NAND flash part advertises 0xD1 as an identifier but is still a working
128MBytes x 8bits 3.3V NAND part.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
After fixing the obvious errors, the driver will now compile
again on v2.6.34-rc3. First tests with two 4MB flash cards including
erase- and write test with one of the cards where successful.
Also, add two new PCMCIA_DEVICE_PROD_IDs.
[linux@dominikbrodowski.net: clean up commit message]
Signed-off-by: Alexander Kurz <linux@kbdbabel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
