* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Fix FDDI and TR config checks in ipv4 arp and LLC.
IPv4: unresolved multicast route cleanup
mac80211: remove association work when processing deauth request
ar9170: wait for asynchronous firmware loading
ipv4: udp: fix short packet and bad checksum logging
phy: Fix initialization in micrel driver.
sctp: Fix a race between ICMP protocol unreachable and connect()
veth: Dont kfree_skb() after dev_forward_skb()
IPv6: fix IPV6_RECVERR handling of locally-generated errors
net/gianfar: drop recycled skbs on MTU change
iwlwifi: work around passive scan issue
Fix an occasional EIO returned by a call to vfs_unlink():
[ 4868.465413] CacheFiles: I/O Error: Unlink failed
[ 4868.465444] FS-Cache: Cache cachefiles stopped due to I/O error
[ 4947.320011] CacheFiles: File cache on md3 unregistering
[ 4947.320041] FS-Cache: Withdrawing cache "mycache"
[ 5127.348683] FS-Cache: Cache "mycache" added (type cachefiles)
[ 5127.348716] CacheFiles: File cache on md3 registered
[ 7076.871081] CacheFiles: I/O Error: Unlink failed
[ 7076.871130] FS-Cache: Cache cachefiles stopped due to I/O error
[ 7116.780891] CacheFiles: File cache on md3 unregistering
[ 7116.780937] FS-Cache: Withdrawing cache "mycache"
[ 7296.813394] FS-Cache: Cache "mycache" added (type cachefiles)
[ 7296.813432] CacheFiles: File cache on md3 registered
What happens is this:
(1) A cached NFS file is seen to have become out of date, so NFS retires the
object and immediately acquires a new object with the same key.
(2) Retirement of the old object is done asynchronously - so the lookup/create
to generate the new object may be done first.
This can be a problem as the old object and the new object must exist at
the same point in the backing filesystem (i.e. they must have the same
pathname).
(3) The lookup for the new object sees that a backing file already exists,
checks to see whether it is valid and sees that it isn't. It then deletes
that file and creates a new one on disk.
(4) The retirement phase for the old file is then performed. It tries to
delete the dentry it has, but ext4_unlink() returns -EIO because the inode
attached to that dentry no longer matches the inode number associated with
the filename in the parent directory.
The trace below shows this quite well.
[md5sum] ==> __fscache_relinquish_cookie(ffff88002d12fb58{NFS.fh,ffff88002ce62100},1)
[md5sum] ==> __fscache_acquire_cookie({NFS.server},{NFS.fh},ffff88002ce62100)
NFS has retired the old cookie and asked for a new one.
[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_ACTIVE,24})
[kslowd] <== fscache_object_state_machine() [->OBJECT_DYING]
[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_INIT,0})
[kslowd] <== fscache_object_state_machine() [->OBJECT_LOOKING_UP]
[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_DYING,24})
[kslowd] <== fscache_object_state_machine() [->OBJECT_RECYCLING]
The old object (OBJ52) is going through the terminal states to get rid of it,
whilst the new object - (OBJ53) - is coming into being.
[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_LOOKING_UP,0})
[kslowd] ==> cachefiles_walk_to_object({ffff88003029d8b8},OBJ53,@68,)
[kslowd] lookup '@68'
[kslowd] next -> ffff88002ce41bd0 positive
[kslowd] advance
[kslowd] lookup 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] next -> ffff8800369faac8 positive
The new object has looked up the subdir in which the file would be in (getting
dentry ffff88002ce41bd0) and then looked up the file itself (getting dentry
ffff8800369faac8).
[kslowd] validate 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] ==> cachefiles_bury_object(,'@68','Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA')
[kslowd] remove ffff8800369faac8 from ffff88002ce41bd0
[kslowd] unlink stale object
[kslowd] <== cachefiles_bury_object() = 0
It then checks the file's xattrs to see if it's valid. NFS says that the
auxiliary data indicate the file is out of date (obvious to us - that's why NFS
ditched the old version and got a new one). CacheFiles then deletes the old
file (dentry ffff8800369faac8).
[kslowd] redo lookup
[kslowd] lookup 'Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA'
[kslowd] next -> ffff88002cd94288 negative
[kslowd] create -> ffff88002cd94288{ffff88002cdaf238{ino=148247}}
CacheFiles then redoes the lookup and gets a negative result in a new dentry
(ffff88002cd94288) which it then creates a file for.
[kslowd] ==> cachefiles_mark_object_active(,OBJ53)
[kslowd] <== cachefiles_mark_object_active() = 0
[kslowd] === OBTAINED_OBJECT ===
[kslowd] <== cachefiles_walk_to_object() = 0 [148247]
[kslowd] <== fscache_object_state_machine() [->OBJECT_AVAILABLE]
The new object is then marked active and the state machine moves to the
available state - at which point NFS can start filling the object.
[kslowd] ==> fscache_object_state_machine({OBJ52,OBJECT_RECYCLING,20})
[kslowd] ==> fscache_release_object()
[kslowd] ==> cachefiles_drop_object({OBJ52,2})
[kslowd] ==> cachefiles_delete_object(,OBJ52{ffff8800369faac8})
The old object, meanwhile, goes on with being retired. If allocation occurs
first, cachefiles_delete_object() has to wait for dir->d_inode->i_mutex to
become available before it can continue.
[kslowd] ==> cachefiles_bury_object(,'@68','Es0g00og0_Nd_XCYe3BOzvXrsBLMlN6aw16M1htaA')
[kslowd] remove ffff8800369faac8 from ffff88002ce41bd0
[kslowd] unlink stale object
EXT4-fs warning (device sda6): ext4_unlink: Inode number mismatch in unlink (148247!=148193)
CacheFiles: I/O Error: Unlink failed
FS-Cache: Cache cachefiles stopped due to I/O error
CacheFiles then tries to delete the file for the old object, but the dentry it
has (ffff8800369faac8) no longer points to a valid inode for that directory
entry, and so ext4_unlink() returns -EIO when de->inode does not match i_ino.
[kslowd] <== cachefiles_bury_object() = -5
[kslowd] <== cachefiles_delete_object() = -5
[kslowd] <== fscache_object_state_machine() [->OBJECT_DEAD]
[kslowd] ==> fscache_object_state_machine({OBJ53,OBJECT_AVAILABLE,0})
[kslowd] <== fscache_object_state_machine() [->OBJECT_ACTIVE]
(Note that the above trace includes extra information beyond that produced by
the upstream code).
The fix is to note when an object that is being retired has had its object
deleted preemptively by a replacement object that is being created, and to
skip the second removal attempt in such a case.
Reported-by: Greg M <gregm@servu.net.au>
Reported-by: Mark Moseley <moseleymark@gmail.com>
Reported-by: Romain DEGEZ <romain.degez@smartjog.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Duplicate entries ended up acpisleep_dmi_table[] by accident.
They don't hurt functionality, but they are ugly, so let's get
rid of them.
Cc: stable@kernel.org
Signed-off-by: Alex Chiang <achiang@canonical.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch just converts the iscsi_ibft module to the
iscsi boot sysfs lib module.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Not all iscsi drivers support ibft. For drivers like be2iscsi
that do not but are bootable through a vendor firmware specific
format/process this patch moves the sysfs interface from the ibft code
to a lib module. This then allows userspace tools to search for iscsi boot
info in a common place and in a common format.
ibft iscsi boot info is exported in the same place as it was
before: /sys/firmware/ibft.
vendor/fw boot info gets export in /sys/firmware/iscsi_bootX, where X is the
scsi host number of the HBA. Underneath these parent dirs, the
target, ethernet, and initiator dirs are the same as they were before.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
For machines with IBFT 1.03 do scan the ACPI table for 'iBFT'
or for 'IBFT'. If the machine is in UEFI mode, only do the ACPI
table scan. For all other machines (pre IBFT 1.03) do
a memory scan if not found in the ACPI tables.
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Tested-by: Mike Christie <michaelc@cs.wisc.edu>
- Use struct acpi_table_ibft instead of struct ibft_table_header
- Don't do reserve_ibft_region() on UEFI machines (section 1.4.3.1)
- If ibft_addr isn't initialized when ibft_init() is called, check for
ACPI-based tables.
- Fix compiler error when CONFIG_ACPI is not defined.
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Peter Jones <pjones@redhat.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
The session->s_waiting list is protected by mdsc->mutex, not s_mutex. This
was causing (rare) s_waiting list corruption.
Fix errors paths too, while we're here. A more thorough cleanup of this
function is coming soon.
Signed-off-by: Sage Weil <sage@newdream.net>
OSD requests need to be resubmitted on any pg mapping change, not just when
the pg primary changes. Resending only when the primary changes results in
occasional 'hung' requests during osd cluster recovery or rebalancing.
Signed-off-by: Sage Weil <sage@newdream.net>
It's possible the MDS will not issue caps on a snapped inode, in which case
an open request may not __ceph_get_fmode(), botching the open file
counting. (This is actually a server bug, but the client shouldn't BUG out
in this case.)
Signed-off-by: Sage Weil <sage@newdream.net>
The osd request wasn't being unregistered when the osd returned a failure
code, even though the result was returned to the caller. This would cause
it to eventually time out, and then crash the kernel when it tried to
resend the request using a stale page vector.
Signed-off-by: Sage Weil <sage@newdream.net>
Prepare the arrays for use with the multiregister function. The
future layer-3 xt matches can then be easily added to it without
needing more (un)register code.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Since xt_action_param is writable, let's use it. The pointer to
'bool hotdrop' always worried (8 bytes (64-bit) to write 1 byte!).
Surprisingly results in a reduction in size:
text data bss filename
5457066 692730 357892 vmlinux.o-prev
5456554 692730 357892 vmlinux.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
In future, layer-3 matches will be an xt module of their own, and
need to set the fragoff and thoff fields. Adding more pointers would
needlessy increase memory requirements (esp. so for 64-bit, where
pointers are wider).
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
The structures carried - besides match/target - almost the same data.
It is possible to combine them, as extensions are evaluated serially,
and so, the callers end up a little smaller.
text data bss filename
-15318 740 104 net/ipv4/netfilter/ip_tables.o
+15286 740 104 net/ipv4/netfilter/ip_tables.o
-15333 540 152 net/ipv6/netfilter/ip6_tables.o
+15269 540 152 net/ipv6/netfilter/ip6_tables.o
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
For Fedora, I want to force perf to link against libiberty.a for
cplus_demangle, rather than libbfd.a for bfd_demangle due to licensing insanity
on binutils. (libiberty is LGPL2, libbfd is GPL3.)
If we just rely on autodetection, we'll end up with libbfd linked against us,
since they're both in binutils-static in the buildroot.
Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <20100510204335.GA7565@bombadil.infradead.org>
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
..otherwise memory allocation errors go undetected.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
In mmp2, 6 banks of GPIO registers are supported. So we can support 192
GPIO pins at most.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.
The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>
This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
