We don't need to protect by BIP whole ret_from_trap/ret_from_exc code.
Only restoring from user/hw exception should be covered.
If BIP is setup, IRQ can't occur.
Signed-off-by: Michal Simek <monstr@monstr.eu>
There is a way howto remove Kernel Mode variable. It is easier
to parse UMS bit in MSR to find out if I come from kernel or user
space. Loading MSR content should be in one cycle and loading
PER_CPU variable depends on memory state.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Save and restore R3/R4 registers in macros. This change
help to cleanup entry.S.
In ret_from_trap function we are saving returning value from
syscall to pt_regs on stack that's why we don't need to save and
restore these values before kernel functions (schedule, do_signal).
Signed-off-by: Michal Simek <monstr@monstr.eu>
_start symbol stores physical address where kernel is.
Gdb uses this symbol for their purpose that's why
we have to rename it.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Lower shifting values ensure that shifted 32bit counter
value doesn't exceed 64bit cycle variable too fast.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Microblaze has support for early printk. The second serial
driver (uart16550/8250) has no microblaze support for early
printk.
Signed-off-by: Michal Simek <monstr@monstr.eu>
HAVE_ARCH_PCI_SET_DMA_MASK was removed in 2.6.34 (no architecture has
the own implementation of pci_set_dma_mask).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Implement intelligent backtracing by searching for stack frame creation,
and emitting only return addresses. Use print_hex_dump() to display the
entire binary kernel stack.
Limitation: MMU kernels are not currently able to trace beyond a system trap
(interrupt, syscall, etc.). It is the intent of this patch to provide
infrastructure that can be extended to add this capability later.
Changes from V1:
* Removed checks in find_frame_creation() that prevented location of the frame
creation instruction in heavily optimized code
* Various formatting/commenting/file location tweaks per review comments
* Dropped Kconfig option to enable STACKTRACE as something logically separate
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Allow developer to configure memory page size at compile time.
Larger pages can improve performance on some workloads.
Based on PowerPC code.
Signed-off-by: Steven J. Magnani <steve@digidescorp.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
sys_clone syscall ignored args which this patch mapped to args
which are passing from glibc.
Here is the origin problem description.
"I ran the static libgcc tests (very few of them are there, they are
mostly dynamically linked) and some of them fail with an assertion in
fork() system call (tid != pid), I looked at the microblaze/entry.S
file and it looks suspicious (ignores arguments 3-5)"
Arg mapping should be:
glibc ARCH_FORK(...) -> do_fork(...)
r5 -> r5 (clone_flags)
r6 -> r6 (stack_start, use parent->stack if NULL)
pt_regs -> r7 (pt_regs)
r7 -> r8 (stack_size)
r8 -> r9 (parent_tidptr)
r9 -> r10 (child_tidptr)
Signed-off-by: John Williams <john.williams@petalogix.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Microblaze doesn't support frame pointers. Ftrace code
uses CALLER_ADDR1 which is defined in linux/ftrace.h. For Microblaze
is 0.
Signed-off-by: Michal Simek <monstr@monstr.eu>
copy_to_user_page macro is used in mm/memory.c:access_process_vm
function. This function is called from ptrace code (POKETEXT, POKEDATA)
which write data to memory. Microblaze handle physical address for
caches that's why there is virt_to_phys conversion.
There is potential one location which can caused the problem on WB system.
The important is take a look at write PTRACEs requests
(POKE/TEXT, DATA, USR).
Note:
Majority of Microblaze PTRACE code is moved to generic location
in newer kernel version that's why this solution should work on
the newest kernel version too.
linux/io.h is in cacheflush because of mm/nommu.c
Tested on a WB system - hello world debugging.
Signed-off-by: Michal Simek <monstr@monstr.eu>
The label should be remove by
21e1c93631
Warning message:
arch/microblaze/mm/fault.c: In function 'do_page_fault':
arch/microblaze/mm/fault.c:229: warning: label 'survive' defined but not used
Signed-off-by: Michal Simek <monstr@monstr.eu>
Some SH-Mobile SoCs have an HDMI controller and a PHY, attached to one of their
LCDC interfaces. This patch adds a preliminary static support for such
controllers, this means, that only the 720p mode is handled ATM. Support for
more modes and a dynamic switching between them will be added by a follow up
patch.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
HDMI support for the sh_mobile_lcdc framebuffer driver will require a 'struct
fb_info *' pointer for its .display_on() callback. While at it fix kfr2r09
framebuffer modular build.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add definitions for DV_CLKI and HDMI clocks, extend support for PLLC2 and some
other clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many system clocks can select a parent by writing a value to a specific field
in the configuration register. Add a list of parents and location and width of
the source selection field in the clock configuration register to struct clk to
assist in clk_set_parent() implementation.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh_mobile_lcdc_setup_clocks() can perform IO, therefore it has to be called
after ioremap(). Also check return code of ioremap() and use resource_size()
instead of open-coding it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With these defines now it is possible to use
gpio_request(GPIO_FN_LCDC1_SELECT, NULL) or ...LCDC0... respectively to
switch between the two LCDC instances.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On AP4EVB board, it is possible to select LCD panel type
which are parallel or MIPI by SW3, SW43 dip-switch.
This patch add parallel LCD settings and
select menu to Kconfig.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Enable burst mode to prevent dropouts during high PCI bus usage.
The card is useless in X without this because of dropouts when anything moves
on the screen (at least with PCI VGA card). Enabling this is also recommended
by the datasheet (page 48).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In patch_alc269(), we initialize the primary capsrc so that the device
works from the beginning. It issues CONNECT_SEL verb no matter which
widget is although some widget (e.g. 0x23) has no connection selection
but a mixer, which requires unmuting instead.
This patch fixes the initialization of capsrc by re-using the code as
a helper function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow platform code to specify callbcks that will be invoked when
input device is opened or closed, allowing, for example, to enable
the device.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Marvell 88ec048 is a derivative of its 88e1121r device. From the programmer's
perspective, the one major difference is the addition of an additional control
bit in Page 2 Register 16 - used to control the padding of odd nibble
preambles.
This patch adds support for this new device, while inheriting as much code as
possible from the existing 88e1121r implementation.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up those functions that depend on knowing whether or not
rpc_restart_call is successful or not.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Both rpc_restart_call_prepare() and rpc_restart_call() test for the
RPC_TASK_KILLED flag, and fail to restart the RPC call if that flag is set.
This patch allows callers to know whether or not the restart was
successful, so that they can perform cleanups etc in case of failure.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
There is no real reason to have RPC_ASSASSINATED() checks in the NFS code.
As far as it is concerned, this is just an RPC error...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
In RFC5661, an NFS4ERR_DELAY error on a SEQUENCE operation has the special
meaning that the server is not finished processing the request. In this
case we want to just retry the request without touching the slot.
Also fix a bug whereby we would fail to update the sequence id if the
server returned any error other than NFS_OK/NFS4ERR_DELAY.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We don't really support nfs servers that invalidate the file handle after a
rename, so precautions such as flushing out dirty data before renaming the
file are superfluous.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
