It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.
Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.
Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.
Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The use of sDMA packet mode in THRESHOLD mode removes the restriction on the
period size.
With the extended THRESHOLD mode user space can ask for any
period size it wishes, and the driver will configure the
sDMA and McBSP FIFO accordingly.
Replace the hw_rule for the period size with static constraint,
which will make sure that the period size will be always
even (to avoid prime period size, which could be possible in
mono stream)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Utilize the sDMA controller's packet syncronization mode, when
the McBSP FIFO is in use (by extending the THRESHOLD mode).
When the sDMA is configured for packet mode, the sDMA frame size
does not need to match with the McBSP threshold configuration.
Uppon DMA request the sDMA will transfer packet size number of
words, and still trigger interrupt on frame boundary.
The patch extends the original THRESHOLD mode by doing the
following:
if (period_words <= max_threshold)
Current THRESHOLD mode configuration
Otherwise (period_words > max_threshold)
McBSP threshold = sDMA packet size
sDMA frame size = period size
With the extended THRESHOLD mode we can remove the constraint
for the maximum period size, since if the period size is
bigger than the maximum allowed threshold, than the driver
will switch to packet mode, and picks the best (biggest)
threshold value, which can divide evenly the period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is a clean up of the code which deals with LM_FLAG_NOEXP
which aims to remove any possible race conditions by using
gl_spin to cover the gap between testing for the LM_FLAG_NOEXP
and the GL_FROZEN flag.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
__copy_to/from_user_inatomic should call __copy_to/from_user
because there is not necessary to check access because of kernel function.
might_sleep in copy_to/from_user macros is causing problems
in debug sessions too (CONFIG_DEBUG_SPINLOCK_SLEEP).
BUG: sleeping function called from invalid context at
.../arch/microblaze/include/asm/uaccess.h:388
in_atomic(): 1, irqs_disabled(): 0, pid: 1, name: swapper
1 lock held by swapper/1:
#0: (&p->cred_guard_mutex){......}, at: [<c00d4b90>] prepare_bprm_creds+0x2c/0x88
Kernel Stack:
...
Call Trace:
[<c0006bd4>] microblaze_unwind+0x7c/0x94
[<c0006684>] show_stack+0xf4/0x190
[<c0006730>] dump_stack+0x10/0x30
[<c00103a0>] __might_sleep+0x12c/0x160
[<c0090de4>] file_read_actor+0x1d8/0x2a8
[<c0091568>] generic_file_aio_read+0x6b4/0xa64
[<c00cd778>] do_sync_read+0xac/0x110
[<c00ce254>] vfs_read+0xc8/0x160
[<c00d585c>] kernel_read+0x38/0x64
[<c00d5984>] prepare_binprm+0xfc/0x130
[<c00d6430>] do_execve+0x228/0x370
[<c000614c>] microblaze_execve+0x58/0xa4
caused by file_read_actor (mm/filemap.c) which calls
__copy_to_user_inatomic.
Signed-off-by: Michal Simek <monstr@monstr.eu>
This is an update that depends on the previous patches I sent.
We can now write to all the appropriate BB marker locations (i.e.
pages 1 AND 2, bytes 1 AND 6) with nand_default_block_markbad() if
necessary, according to the flags marked in chip->options.
Note that I removed the line:
ofs += mtd->oobsize;
Unless I am wrong, this line was completely unnecessary in the
first place.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix all checkpatch.pl complaints.
Artem: tweaked a little and fix tab indentations, so now this is not
only about checkpatch, but also about making indentations look
sane.
Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
On TI's DA830/OMAP-L137, DA850/OMAP-L138 and DM365, after setting the
4BITECC_ADD_CALC_START bit in the NAND Flash control register to 1 and
before waiting for the NAND Flash status register to be equal to 1, 2 or
3, we have to wait till the ECC HW goes to correction state. Without this
wait, ECC correction calculations will not be proper.
This has been tested on DA830/OMAP-L137, DA850/OMAP-L138, DM355 and DM365
EVMs.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Sneha Narnakaje <nsnehaprabha@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a revision to PATCH 2/2 that I sent. Link:
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html
Added new flag for scanning of both bytes 1 and 6 of the OOB for
a BB marker (instead of simply one or the other).
The "check_pattern" and "check_short_pattern" functions were updated
to include support for scanning the two different locations in the OOB.
In order to handle increases in variety of necessary scanning patterns,
I implemented dynamic memory allocation of nand_bbt_descr structs
in new function 'nand_create_default_bbt_descr()'. This replaces
some increasingly-unwieldy, statically-declared descriptors. It can
replace several more (e.g. "flashbased" structs). However, I do not
test the flashbased options personally.
How this was tested:
I referenced 30+ data sheets (covering 100+ parts), and I tested a
selection of 10 different chips to varying degrees. Particularly, I
tested the creation of bad-block descriptors and basic BB scanning on
three parts:
ST NAND04GW3B2D, 2K page
ST NAND128W3A, 512B page
Samsung K9F1G08U0A, 2K page
To test these, I wrote some fake bad block markers to the flash (in OOB
bytes 1, 6, and elsewhere) to see if the scanning routine would detect
them properly. However, this method was somewhat limited because the
driver I am using has some bugs in its OOB write functionality.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Conflicts:
drivers/firewire/core-card.c
drivers/firewire/core-cdev.c
and forgotten #include <linux/time.h> in drivers/firewire/ohci.c
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Some level of support for various scanning locations was already built in,
but this required clean-up. First, BB marker location cannot be determined
_only_ by the page size. Instead, I implemented some heuristic detection
based on data sheets from various manufacturers (all found in
nand_base.c:nand_get_flash_type()).
Second, once these options were identified, they were not handled properly
by nand_bbt.c:nand_default_bbt(). I updated the static nand_bbt_desc structs
to reflect the need for more combinations of detection. The memory allocation
here probably needs to be done dynamically in the very near future (see next
patches).
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Current driver prevents command-line partitions from being parsed when built-in
partitions are defined in s3c2410_nand_set object, but it is not desirable in some
cases. This patch tries to parse commad-line partitions prior to the built-in.
Signed-off-by: Conke Hu <conke@maxwit.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Test if a lock or unlock function is present (pointer not NULL) before
calling it, to prevent a kernel dump.
Artem: removed extra blank lines
Signed-off-by: Martin Krause <martin.krause@tqs.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Included the basic size info for NAND chips with ID of 0xAD or
0xD7. The first can be found in Hynix HY27SF161G2M, while the
second can be found in Micron MT29F64G08 and the Samsung K9LBG08U0D
(among others). Also, some 64 Gbit (or larger) chips identify as
0xD7 because they contain multiple smaller 32 Gbit chips. I
assume it's safe to classify these under the 32 Gbit listing.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes:
drivers/mtd/nand/mxc_nand.c: In function 'mxcnd_resume':
drivers/mtd/nand/mxc_nand.c:901: warning: unused variable 'host'
Removing this variable was missed in 9c14b153e6.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patchs adds a way for user space programs to find out whether a
flash sector is locked. An optional driver method in the mtd_info struct
provides the information.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The OOB handling in the mxc_nand driver is broken for v1 type
controllers (i.MX27/31) with 512 byte page size. This perhaps
did not show up because ubi does not use OOB.
Update the driver to always read/write a whole page even if
only OOB is requested. With this patch the driver passes the
mtd_oobtest on i.MX27 with 512 byte page size. Also tested
with 2048 byte page size and on i.MX35 (v2 type controller)
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The rest of the function assumes that "data" can be null. I don't know
the code well enough to say whether it can actually be null, but there
is no harm in checking here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Match usb ids in usb/quirks-table.h for some Hauppage HVR-950Q models
and for the HVR850 model to those ids at the end of au0828-cards.c
Thanks to nhJm449 for pointing out the problem.
Signed-off-by: John S Gruber <JohnSGruber@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an at least theoretic race condition in which .start_iso etc.
could still be called between when the dummy driver is bound to the card
and when the children devices are being shut down. Add dummy_start_iso
and friends.
On the other hand, .enable, .set_config_rom, .read_csr, write_csr do not
need to be implemented by the dummy driver, as commented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Current selinux policy can have over 3000 types. The type_attr_map in
policy is an array sized by the number of types times sizeof(struct ebitmap)
(12 on x86_64). Basic math tells us the array is going to be of length
3000 x 12 = 36,000 bytes. The largest 'safe' allocation on a long running
system is 16k. Most of the time a 32k allocation will work. But on long
running systems a 64k allocation (what we need) can fail quite regularly.
In order to deal with this I am converting the type_attr_map to use
flex_arrays. Let the library code deal with breaking this into PAGE_SIZE
pieces.
-v2
rework some of the if(!obj) BUG() to be BUG_ON(!obj)
drop flex_array_put() calls and just use a _get() object directly
-v3
make apply to James' tree (drop the policydb_write changes)
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Stephen D. Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
Kconfig and Makefiles to enable configuration and building of AppArmor.
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Commit c9e69318 "TOMOYO: Allow wildcard for execute permission." changed execute
permission and domainname to accept wildcards. But tomoyo_find_next_domain()
was using pathname passed to execve() rather than pathname specified by the
execute permission. As a result, processes were not able to transit to domains
which contain wildcards in their domainnames.
This patch passes pathname specified by the execute permission back to
tomoyo_find_next_domain() so that processes can transit to domains which
contain wildcards in their domainnames.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Remove extraneous path_truncate arguments from the AppArmor hook,
as they've been removed from the LSM API.
Signed-off-by: James Morris <jmorris@namei.org>
