bcm_config_lre_aneg() is the only user of genphy_config_eee_advert(),
therefore use genphy_c45_an_config_eee_aneg() instead. The resulting
functionality is equivalent, and bcm_config_lre_aneg() follows the
structure of __genphy_config_aneg().
In a follow-up step genphy_config_eee_advert() can be removed.
Note: We preserve the current behavior to ignore errors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/6e5cd4ab-28bb-4d82-b449-fec85f3d1e8a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we remove modes from EEE advertisement and disable / re-enable EEE,
then advertisement is set to all supported modes. I don't think this is
what the user expects. So respect the cached advertisement and just fall
back to all supported modes if cached advertisement is empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c75f7f8b-5571-429f-abd3-ce682d178a4b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad937 ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Like the DP83826, the DP83825 can also be configured as an RMII master or
slave via a control register. The existing function responsible for this
configuration is renamed to a general dp8382x function. The DP83825 only
supports RMII so nothing more needs to be configured.
With this change, the dp83822_driver list is reorganized according to the
device name.
Signed-off-by: Erik Schumacher <erik.schumacher@iris-sensing.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/aa62d081804f44b5af0e8de2372ae6bfe1affd34.camel@iris-sensing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch propagates error code correctly in cal_cycle()
and improve with FIELD_GET().
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch shrinks line wrapping to 80 chars. Also, in
tx_amp_fill_result(), use FIELD_PREP() to prettify code.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch fixes spelling errors, re-arrange vars with
reverse Xmas tree and remove unnecessary parens in
mediatek-ge-soc.c.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This change fixes a rare issue where the PHY fails to detect a link
due to incorrect reset behavior.
The SW_RESET definition was incorrectly assigned to bit 14, which is the
Digital Restart bit according to the datasheet. This commit corrects
SW_RESET to bit 15 and assigns DIG_RESTART to bit 14 as per the
datasheet specifications.
The SW_RESET define is only used in the phy_reset function, which fully
re-initializes the PHY after the reset is performed. The change in the
bit definitions should not have any negative impact on the functionality
of the PHY.
v2:
- added Fixes tag
- improved commit message
Cc: stable@vger.kernel.org
Fixes: 5dc39fd5ef ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <AS1P250MB0608A798661549BF83C4B43EA9462@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The Realtek RTL8125/RTL8126 NBase-T MAC/PHY chips have internal PHY's
which are register-compatible, at least for the registers we use here.
So let's use just one PHY driver to support all of them.
These internal PHY's exist also as external C45 PHY's, but on the
internal PHY's no access to MMD registers is possible. This can be
used to differentiate between the internal and external version.
As a side effect the drivers for two now external-only drivers don't
require read_mmd/write_mmd hooks any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c57081a6-811f-4571-ab35-34f4ca6de9af@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use newly defined 'active-high' property to set the
VEND1_GLOBAL_LED_DRIVE_VDD bit and let 'active-low' clear that bit. This
reflects the technical reality which was inverted in the previous
description in which the 'active-low' property was used to actually set
the VEND1_GLOBAL_LED_DRIVE_VDD bit, which means that VDD (ie. supply
voltage) of the LED is driven rather than GND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/86a413b4387c42dcb54f587cc2433a06f16aae83.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
For TJA11xx PHYs, they have the capability to output 50MHz reference
clock on REF_CLK pin in RMII mode, which is called "revRMII" mode in
the PHY data sheet.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As per LAN8650/1 Rev.B0/B1 AN1760 (Revision F (DS60001760G - June 2024))
and LAN8670/1/2 Rev.C1/C2 AN1699 (Revision E (DS60001699F - June 2024)),
under normal operation, the device should be operated in PLCA mode.
Disabling collision detection is recommended to allow the device to
operate in noisy environments or when reflections and other inherent
transmission line distortion cause poor signal quality. Collision
detection must be re-enabled if the device is configured to operate in
CSMA/CD mode.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-8-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The system interface connection status register is not immediately
correct upon line side link up. This results in the status being read as
OFF and then transitioning to the correct host side link mode with a
short delay. This causes the phylink framework passing the OFF status
down to all MAC config drivers, resulting in the host side link being
misconfigured, which in turn can lead to link flapping or complete
packet loss in some cases.
Mitigate this by periodically polling the register until it not showing
the OFF state. This will be done every 1ms for 10ms, using the same
poll/timeout as the processor intensive operation reads.
If the phy is still expressing the OFF state after the timeout, then set
the link to false and pass the NA interface mode onto the phylink
framework.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241010004935.1774601-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Validate PHY LED OPs presence before registering and parsing them.
Defining LED nodes for a PHY driver that actually doesn't supports them
is redundant and useless.
It's also the case with Generic PHY driver used and a DT having LEDs
node for the specific PHY.
Skip it and report the error with debug print enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241008194718.9682-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
All MMD reads return 0 for the RTL8126A-integrated PHY. Therefore phylib
assumes it doesn't support EEE, what results in higher power consumption,
and a significantly higher chip temperature in my case.
To fix this split out the PHY driver for the RTL8126A-integrated PHY
and set the read_mmd/write_mmd callbacks to read from vendor-specific
registers.
Fixes: 5befa3728b ("net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial marvell-88q2xxx driver only supported the Marvell 88Q2110
PHY without auto negotiation support. The reason documented states that
the provided initialization sequence did not to work. Now a method to
enable auto negotiation have been found by comparing the initialization
of other supported devices and an out-of-tree PHY driver.
Perform the minimal needed initialization of the PHY to get auto
negotiation working and remove the limitation that disables the auto
negotiation feature for the mv88q2110 device.
With this change a 1000Mbps full duplex link is able to be negotiated
between two mv88q2110 and the link works perfectly. The other side also
reflects the manually configure settings of the master device.
# ethtool eth0
Settings for eth0:
Supported ports: [ ]
Supported link modes: 100baseT1/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 100baseT1/Full
1000baseT1/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 100baseT1/Full
1000baseT1/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred master
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 15/15
Before this change I was not able to manually configure 1000Mbps link,
only a 100Mpps link so this change providers an improvement in
performance for this device.
[ 5] local 10.1.0.2 port 5201 connected to 10.1.0.1 port 38346
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 96.8 MBytes 812 Mbits/sec 0 469 KBytes
[ 5] 1.00-2.00 sec 94.3 MBytes 791 Mbits/sec 0 469 KBytes
[ 5] 2.00-3.00 sec 96.1 MBytes 806 Mbits/sec 0 469 KBytes
[ 5] 3.00-4.00 sec 98.3 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 4.00-5.00 sec 98.4 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 5.00-6.00 sec 98.4 MBytes 826 Mbits/sec 0 469 KBytes
[ 5] 6.00-7.00 sec 98.9 MBytes 830 Mbits/sec 0 469 KBytes
[ 5] 7.00-8.00 sec 91.7 MBytes 769 Mbits/sec 0 469 KBytes
[ 5] 8.00-9.00 sec 99.4 MBytes 834 Mbits/sec 0 747 KBytes
[ 5] 9.00-10.00 sec 101 MBytes 851 Mbits/sec 0 747 KBytes
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241005112412.544360-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
