This adds the board level device tree specification for LEGO MINDSTORMS EV3
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The LD11 SoC is equipped with not only MIO-reset but also SD-reset
for controlling RST_n pin of the eMMC device.
Update the binding document and remove unneeded "." from each line
in itemization.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch adds support for the PM8994 regulators found on msm8992,
msm8994 and msm8996 platforms.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Add DT binding doc and vdd_lvs1_2 supply]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
IDT 89HPESx PCIe-switches exposes SMBus interface to have an access to
the device CSRs and EEPROM. So to properly utilize the interface
functionality, developer should declare a valid dts-file node, which
would refer to the corresponding 89HPESx device.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
MSS rproc loader need chip specific resources initialization during probe
to load and boot modem firmware, this need compatible string based
differentiation in resources to be initialized. This patch add and provide
a template struct whose fields represent all those resources which are
needed to load and boot modem fw and which may differ from chip to chip.
This patch also add new compatible string for msm8916, msm8974 platform.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pull networking fixes from David Miller:
1) Handle multicast packets properly in fast-RX path of mac80211, from
Johannes Berg.
2) Because of a logic bug, the user can't actually force SW
checksumming on r8152 devices. This makes diagnosis of hw
checksumming bugs really annoying. Fix from Hayes Wang.
3) VXLAN route lookup does not take the source and destination ports
into account, which means IPSEC policies cannot be matched properly.
Fix from Martynas Pumputis.
4) Do proper RCU locking in netvsc callbacks, from Stephen Hemminger.
5) Fix SKB leaks in mlxsw driver, from Arkadi Sharshevsky.
6) If lwtunnel_fill_encap() fails, we do not abort the netlink message
construction properly in fib_dump_info(), from David Ahern.
7) Do not use kernel stack for DMA buffers in atusb driver, from Stefan
Schmidt.
8) Openvswitch conntack actions need to maintain a correct checksum,
fix from Lance Richardson.
9) ax25_disconnect() is missing a check for ax25->sk being NULL, in
fact it already checks this, but not in all of the necessary spots.
Fix from Basil Gunn.
10) Action GET operations in the packet scheduler can erroneously bump
the reference count of the entry, making it unreleasable. Fix from
Jamal Hadi Salim. Jamal gives a great set of example command lines
that trigger this in the commit message.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (46 commits)
net sched actions: fix refcnt when GETing of action after bind
net/mlx4_core: Eliminate warning messages for SRQ_LIMIT under SRIOV
net/mlx4_core: Fix when to save some qp context flags for dynamic VST to VGT transitions
net/mlx4_core: Fix racy CQ (Completion Queue) free
net: stmmac: don't use netdev_[dbg, info, ..] before net_device is registered
net/mlx5e: Fix a -Wmaybe-uninitialized warning
ax25: Fix segfault after sock connection timeout
bpf: rework prog_digest into prog_tag
tipc: allocate user memory with GFP_KERNEL flag
net: phy: dp83867: allow RGMII_TXID/RGMII_RXID interface types
ip6_tunnel: Account for tunnel header in tunnel MTU
mld: do not remove mld souce list info when set link down
be2net: fix MAC addr setting on privileged BE3 VFs
be2net: don't delete MAC on close on unprivileged BE3 VFs
be2net: fix status check in be_cmd_pmac_add()
cpmac: remove hopeless #warning
ravb: do not use zero-length alignment DMA descriptor
mlx4: do not call napi_schedule() without care
openvswitch: maintain correct checksum state in conntrack actions
tcp: fix tcp_fastopen unaligned access complaints on sparc
...
Pull MTD fixes from Brian Norris:
"Just NAND updates from Boris:
- avoid compiling xway NAND controller driver as a module (which
didn't work)
- fix tango NAND DT binding and make sure the controller is in a
clean state at probe time
- add dependency on HAS_IOMEM to the oxnas NAND driver
- fix irq number validity check in the lpc32xx driver"
* tag 'for-linus-20170116' of git://git.infradead.org/linux-mtd:
mtd: nand: lpc32xx: fix invalid error handling of a requested irq
mtd: nand: tango: Reset pbus to raw mode in probe
mtd: nand: tango: Update DT binding description
mtd: nand: oxnas_nand: fix build errors on arch/um, require HAS_IOMEM
mtd: nand: xway: fix build because of module functions
mtd: nand: xway: disable module support
Add a binding for the regulator which controls the OTG chargepath switch.
The OTG switch gets its power from pm8941_5vs1, and that should be
expressed as a usb_otg_in-supply property in the DT node for the
charger driver. The regulator name is "otg-vbus".
Signed-off-by: Tim Bird <tim.bird@sonymobile.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently dp83867 driver returns error if phy interface type
PHY_INTERFACE_MODE_RGMII_RXID is used to set the rx only internal
delay. Similarly issue happens for PHY_INTERFACE_MODE_RGMII_TXID.
Fix this by checking also the interface type if a particular delay
value is missing in the phy dt bindings. Also update the DT document
accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allwinner V3s come with a USB PHY controller slightly different to other
SoCs, with only one PHY.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit 46dcf0ff0d ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
This driver currently only supports legacy platform data probe. This
change adds device tree support and gets rid of platform data probe code
since no one is actually using mpr121 platform data in the mainline.
The device tree property parsing code is based on the work of
atmel_captouch driver.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds device tree bindings for the TI ADS7950 family of A/DC chips.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Johannes Berg says:
====================
For 4.11, we seem to have more than in the past few releases:
* socket owner support for connections, so when the wifi
manager (e.g. wpa_supplicant) is killed, connections are
torn down - wpa_supplicant is critical to managing certain
operations, and can opt in to this where applicable
* minstrel & minstrel_ht updates to be more efficient (time and space)
* set wifi_acked/wifi_acked_valid for skb->destructor use in the
kernel, which was already available to userspace
* don't indicate new mesh peers that might be used if there's no
room to add them
* multicast-to-unicast support in mac80211, for better medium usage
(since unicast frames can use *much* higher rates, by ~3 orders of
magnitude)
* add API to read channel (frequency) limitations from DT
* add infrastructure to allow randomizing public action frames for
MAC address privacy (still requires driver support)
* many cleanups and small improvements/fixes across the board
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for TI TMP007 - 16 bit IR thermopile sensor with integrated Math engine.
Sensor takes care of calculating the object temperature with the help of calibrated constants stored in non-volatile memory,
thereby reducing the calculation overhead.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Rockchip's RC produces a 100MHz reference clock but there are two methods
for the PHY to generate it:
(1) Use the system PLL to generate a 100MHz clock. The PHY will relock
it, filter signal noise, and output the reference clock. ASPM L0s
works correctly, but circuit noise issues make it difficult to pass
the TX compatibility test.
(2) Share the SoC's 24MHZ crystal oscillator with the PHY and force the
PHY's PLL to generate 100MHz internally. In this case, exit from
ASPM L0s sometimes fails due to a design error in the RC receiver
circuit. Even if we use extended-synch, the PHY sometimes fails to
relock the bits from FTS, which will hang the system.
We want the flexibility to use both clocking methods, so add a DT property,
"aspm-no-l0s". If that's present, disable L0s to avoid the issues with
case (2).
[bhelgaas: changelog]
Reported-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Falling back unconditionally to HostNotify as primary client's interrupt
breaks some drivers which alter their functionality depending on whether
interrupt is present or not, so let's introduce a board flag telling I2C
core explicitly if we want wired interrupt or HostNotify-based one:
I2C_CLIENT_HOST_NOTIFY.
For DT-based systems we introduce "host-notify" property that we convert
to I2C_CLIENT_HOST_NOTIFY board flag.
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fix couple of typos in the example given in the TI syscon reset
binding. The ti,reset-bits used for DSP0 are corrected to match
the values that will be used in the actual DT node.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The bq27xxx binding is a standard i2c style binding, however the
deprecated compatible fields and different revisions warrant its own
documentation.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
'uart-has-rtscts' is a generic serial property and it is described
at Documentation/devicetree/bindings/serial/serial.txt, so remove it
from the specific fsl-imx-uart binding documentation.
While at it, add a note pointing to the serial.txt file, which
contains the complete list of generic serial bindings.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The vendor prefix for Fujitsu is used in the tree, but it's
still missing from the documentation, so add it. Fujitsu Ltd.
is a japanese ICT company, http://www.fujitsu.com
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
In the new DTS bindings for DSA (dsa2), the "ethernet" and "link"
phandles are respectively mandatory and exclusive to CPU port and DSA
link device tree nodes.
Simplify dsa2.c a bit by checking the presence of such phandle instead
of checking the redundant "label" property.
Then the Linux philosophy for Ethernet switch ports is to expose them to
userspace as standard NICs by default. Thus use the standard enumerated
"eth%d" device name if no "label" property is provided for a user port.
This allows to save DTS files from subjective net device names.
If one wants to rename an interface, udev rules can be used as usual.
Of course the current behavior is unchanged, and the optional "label"
property for user ports has precedence over the enumerated name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds device tree bindings document for ZTE zx2967
family power domain controller.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT bindings for avia,hx711
Add vendor avia to vendor list
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
