Expedited grace periods no longer fall back to normal grace periods
in response to lock contention, given that expedited grace periods
now use the rcu_node tree so as to avoid contention. This commit
therfore removes the expedited_normal counter.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Add code to support support for "anatop-enable-bit" device-tree
property. This property translates to LINREG_ENABLE bit in real hardware
and is present on 1p1, 2p5 and 3p0 regulators on i.MX6 and 1p0d regulator
on i.MX7.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add prefix for WeTek Electronics, limited, a company producing multimedia
Set-Top-Boxes and supporting KODI and LibreELEC distributions.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This commit adds a compatible string for everest,es8388. This is
an audio codec that is compatible with es8328.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define bindings for pwm-stm32
version 9:
- change commit message header
version 8:
- reword st,breakinput description.
version 6:
- change st,breakinput parameter format to make it usuable on stm32f7 too.
version 2:
- use parameters instead of compatible of handle the hardware configuration
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add bindings information for STM32 Timers
version 6:
- rename stm32-gtimer to stm32-timers
- change compatible
- add description about the IPs
version 2:
- rename stm32-mfd-timer to stm32-gptimer
- only keep one compatible string
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A new iommu-group sysfs attribute file is introduced. It contains
the list of reserved regions for the iommu-group. Each reserved
region is described on a separate line:
- first field is the start IOVA address,
- second is the end IOVA address,
- third is the type.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
Parse the "brcm,use-bcm-hdr" boolean property during ports
identification to fill a bitmask of ports that should have Broadcom tags
enabled. This is needed in some configurations where per-packet metadata
can be exchanged using Broadcom tags between the switch and an on-chip
acceleration device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the integrated switch found on BCM7278:
- core_reg_align is set to 1, to force a translation into the target
address space which is 8 bytes aligned
- an alternate SWITCH_REG layout is provided since registers are largely
bit/masks compatible but have different offsets
- conditional for all CORE_STS_OVERRIDE_{IMP,GMII_P} since those got
moved way out of the traditional register space
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add supporf for the SYSTEMPORT Lite Ethernet controller, this piece of hardware
is largely based on the full-blown SYSTEMPORT and differs in the following:
- no full-blown UniMAC, instead we have the MagicPacket matching from UniMAC at
same offset, and a GMII Interface Block (GIB) for the MAC-level stuff, since
we are always interfaced to an Ethernet switch which is fully Ethernet compliant
shortcuts could be made
- 16 transmit queues, whose interrupts are moved into the first Level-2 interrupt
controller bank
- slight TDMA offset change (a register was inserted after TDMA_STATUS, *sigh*)
- 256 RX descriptors (512 words) and 256 TX descriptors (not visible)
As a consequence of these two things, update the code paths accordingly to
differentiate the full-blown from the light version.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an optional regulator to the pwm-beeper device. This regulator
acts as an amplifier. The amplifier is only enabled while beeping in order
to reduce power consumption.
Tested on LEGO MINDSTORMS EV3, which has a speaker connected to PWM through
an amplifier.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for Texas Instruments TMP122/124 which are nearly identical to
their TMP121/123 except that they also support programmable temperature
thresholds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The DSI pixel clocks are muxed from clocks generated in the analog phy
by the DSI driver. In order to set them as parents, we need to do the
same name lookup dance on them as we do for our root oscillator.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Pull Rockchip clk updates from Heiko Stuebner:
A new clock-type for the 1-2 muxes per soc that are for whatever reason
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
* tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: clk: add rockchip,grf property for RK3399
clk: rockchip: use clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: use rk3288 isp_in clock ids
clk: rockchip: add clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: add rk3288 isp_in clock ids
clk: rockchip: Remove useless init of "grf" to -EPROBE_DEFER
clk: rockchip: add clock controller for rk3328
dt-bindings: add bindings for rk3328 clock controller
clk: rockchip: add dt-binding header for rk3328
clk: rockchip: add new pll-type for rk3328
clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288
clk: rockchip: add a clock-type for muxes based in the grf
Pull Samsung clk updates from Sylwester Nawrocki:
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
* tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
Allwinner V3s is now driven by sunxi-ng CCU driver.
Add devicetree binding for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s is a low-end single-core Cortex-A7 SoC, with 64MB
integrated DRAM, and several peripherals.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pull spi fixes from Mark Brown:
"The usual small smattering of driver specific fixes. A few bits that
stand out here:
- the R-Car patches adding fallbacks are just adding new compatible
strings to the driver so that device trees are written in a more
robustly future proof fashion, this isn't strictly a fix but it's
just new IDs and it's better to get it into mainline sooner to
improve the ABI
- the DesignWare "switch to new API part 2" patch is actually a
misleadingly titled fix for a bit that got missed in the original
conversion"
* tag 'spi-fix-v4.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: davinci: use dma_mapping_error()
spi: spi-axi: Free resources on error path
spi: pxa2xx: add missed break
spi: dw-mid: switch to new dmaengine_terminate_* API (part 2)
spi: dw: Make debugfs name unique between instances
spi: sh-msiof: Do not use C++ style comment
spi: armada-3700: Set mode bits correctly
spi: armada-3700: fix unsigned compare than zero on irq
spi: sh-msiof: Add R-Car Gen 2 and 3 fallback bindings
spi: SPI_FSL_DSPI should depend on HAS_DMA
This adds "microchip,24c128" to the list of compatible strings for i2c
eeproms.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds the board level device tree specification for LEGO MINDSTORMS EV3
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The LD11 SoC is equipped with not only MIO-reset but also SD-reset
for controlling RST_n pin of the eMMC device.
Update the binding document and remove unneeded "." from each line
in itemization.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Revert commit 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0
flag) as it caused system suspend (in the default configuration) to fail
on Dell XPS13 (9360) with the Kaby Lake processor.
Fixes: 08b98d3291 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag)
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds the DMA_ATTR_PRIVILEGED attribute to the DMA-mapping
subsystem.
Some advanced peripherals such as remote processors and GPUs perform
accesses to DMA buffers in both privileged "supervisor" and unprivileged
"user" modes. This attribute is used to indicate to the DMA-mapping
subsystem that the buffer is fully accessible at the elevated privilege
level (and ideally inaccessible or at least read-only at the
lesser-privileged levels).
Cc: linux-doc@vger.kernel.org
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds support for the PM8994 regulators found on msm8992,
msm8994 and msm8996 platforms.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
[bjorn: Add DT binding doc and vdd_lvs1_2 supply]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
IDT 89HPESx PCIe-switches exposes SMBus interface to have an access to
the device CSRs and EEPROM. So to properly utilize the interface
functionality, developer should declare a valid dts-file node, which
would refer to the corresponding 89HPESx device.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
I am still tired of having to find indirect ways to determine
what security modules are active on a system. I have added
/sys/kernel/security/lsm, which contains a comma separated
list of the active security modules. No more groping around
in /proc/filesystems or other clever hacks.
Unchanged from previous versions except for being updated
to the latest security next branch.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: John Johansen <john.johansen@canonical.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
MSS rproc loader need chip specific resources initialization during probe
to load and boot modem firmware, this need compatible string based
differentiation in resources to be initialized. This patch add and provide
a template struct whose fields represent all those resources which are
needed to load and boot modem fw and which may differ from chip to chip.
This patch also add new compatible string for msm8916, msm8974 platform.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This driver allows rpmsg instances to expose access to rpmsg endpoints
to user space processes. It provides a control interface, allowing
userspace to export endpoints and an endpoint interface for each exposed
endpoint.
The implementation is based on prior art by Texas Instrument, Google,
PetaLogix and was derived from a FreeRTOS performance statistics driver
written by Michal Simek.
The control interface provides a "create endpoint" ioctl, which is fed a
name, source and destination address. The three values are used to
create the endpoint, in a backend-specific way, and a rpmsg endpoint
device is created - with the three parameters are available in sysfs for
udev usage.
E.g. to create an endpoint device for one of the Qualcomm SMD channel
related to DIAG one would issue:
struct rpmsg_endpoint_info info = { "DIAG_CNTL", 0, 0 };
int fd = open("/dev/rpmsg_ctrl0", O_RDWR);
ioctl(fd, RPMSG_CREATE_EPT_IOCTL, &info);
Each created endpoint device shows up as an individual character device
in /dev, allowing permission to be controlled on a per-endpoint basis.
The rpmsg endpoint will be created and destroyed following the opening
and closing of the endpoint device, allowing rpmsg backends to open and
close the physical channel, if supported by the wire protocol.
Cc: Marek Novak <marek.novak@nxp.com>
Cc: Matteo Sartori <matteo.sartori@t3lab.it>
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
