Defconfig updates for omaps for v4.12 merge window. Mostly
to update to use new ti-cpufreq driver, the rest is just
to enable drivers found on various devices:
- Update to use ti-cpufreq driver that we now have
- Enable SATA for ti81xx as a loadable module
- Enable Ethernet PHY for DP83848
- Enable modem related modules for PPP, QMI and USB ACM
as loadable modules
- Enable droid 4 related drivers as lodable modules except
for PMIC and regulator so eMMC can be used for root
* tag 'omap-for-v4.12/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable droid 4 devices
ARM: omap2plus_defconfig: Add QMI, ACM and PPP as loadable modules
ARM: omap2plus_defconfig: Enable TI Ethernet PHY
ARM: omap2plus_defconfig: enable ahci-dm816 module
ARM: omap2plus_defconfig: Enable support for ti-cpufreq
Signed-off-by: Olof Johansson <olof@lixom.net>
We only need to have MFD_CPCAP and CPCAP_REGULATOR as built-in to
be able to mount root on the eMMC. And then POWER_RESET_GPIO
is good to have built-in. The rest of the devices can be loadable
modules.
This gets various devices such as regulators, touchscreen, power
button, HDMI audio, LEDs, RTC, and ADC working.
Note that omapdrm needs to be configured manually as we're still
using omapfb by default.
Signed-off-by: Tony Lindgren <tony@atomide.com>
DP83848_PHY i.e. [TI TLK10X 10/100 Mbps PHY] is used on the
am335x-icev2 board. Enable the PHY driver for it.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is now supported on the dm8168-evm board, so enable it in
the defconfig for omap2+.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x, AM437x, DRA7xx, and AM57xx platforms all now depend on
ti-cpufreq driver to enable proper OPPs for use with cpufreq, so
enable the same.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x SoM has a RV4162 RTC populated which is supported
by the M41T80 driver. Enabled it so make the RTC support on the SoM
available.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x SoM with PCM-953 carrierboard has a
KSZ9021 phy mounted. To add support for this we need to enable
the micrell phy driver in the config.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP2 plus defconfig lists the LIS3LC02D MISC driver
but there is nowadays a proper IIO driver for this accelerometer.
Switch the config to the new driver.
The IIO software triggers are helpful when using these devices
without a dedicated IRQ line, so activate those too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This shrinks down omap2plus_defconfig a bit and makes it easier for
people to generate minimal patches against it.
Signed-off-by: Tony Lindgren <tony@atomide.com>
LP873X family of PMICs are used in dra71x-evm, So enable the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO regulator is used on dra71-evm platform to control MMCSD IO
voltage
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LogicPD DM3730 Torpedo and SOM-LV devices have the TI
TSC2004 touchscreen controller. Enable the related driver as
a module.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This alters the OMAP2plus defconfig to use the IIO BMP280
driver, which is compatible with the BMP085 instead of the old
BMP085-specific misc driver. The IIO driver nowadays have all
the features of the old driver and more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 648af7fca1 ("rxrpc: Absorb the rxkad security module") changed
the RXKAD Kconfig symbol from tristate to boolean but the commit didn't
update the omap2plus_defconfig that was enabling CONFIG_RXKAD as module.
This leads to the following warning when using the omap2plus_defconfig:
arch/arm/configs/omap2plus_defconfig:112:warning: symbol value 'm' invalid for RXKAD
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MDIO Bus/PHY emulation with fixed speed/link PHYs will be used in
Baltos iR5221 devices to connect to ICPlus IP175D switch IC.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable DP83867 Ethernet phy for supporting networking on DRA72-EVM rev C
(SR2.0).
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the TI TPIC2810 8-Bit LED Driver with I2C Interface. This is used
in AM335x ICEv2 Boards.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC defconfig updates from Arnd Bergmann:
"As usual, a bunch of commits, mostly adding drivers and other options
to defconfigs.
The realview_smp_defconfig and realview_defconfig got merged into one,
so we are now down to 110 files.
For stm32, we have now added a Kconfig fragment, the first such file
on arch/arm. The purpose here is to have a shared defconfig file that
works for all boards, while the DRAM offset has to be hardwired on
NOMMU machines at compile time.
The Exynos defconfig changes depend on changes in the RTC tree, so
this is pulled in here, but has already been merged into 4.6 now"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: imx_v4_v5_defconfig: Enable initramfs support
ARM: imx_v4_v5_defconfig: Cleanup imx_v4_v5_defconfig
ARM: multi_v7_defconfig: Enable LP872x regulator support
ARM: omap2plus_defconfig: Enable LP872x regulator support
ARM: mxs_defconfig: Enable initramfs support
ARM: mxs_defconfig: Cleanup mxs_defconfig
ARM: multi_v5_defconfig: Enable initramfs support
ARM: multi_v5_defconfig: Cleanup multi_v5_defconfig
ARM: multi_v7_defconfig: enable useful configurations for Vybrid
ARM: multi_v7_defconfig: add MACH_ARTPEC6
ARM: omap2plus_defconfig: Enable AT24 eeprom
ARM: omap2plus_defconfig: Enable TI TVP5150 video decoder support
ARM: omap2plus_defconfig: Enable ISP support and dependencies
ARM: omap2plus_defconfig: Enable OMAP IOMMU support
ARM: socfpga_defconfig: enable support for initramfs/initrd support
ARM: at91/defconfig: add sama5d2 adc support in sama5_defconfig
ARM: multi_v7_defconfig: Enable BCM283x
ARM: bcm2835_defconfig: Enable RPi power domain driver
ARM: bcm2835_defconfig: Enable RPi firmware driver
ARM: bcm2835_defconfig: enable ARMv7 support
...
Merge "omap defconfig changes for v4.6 merge window" from Tony Lindgren:
Defconfig changes for omap2plus_defconfig and multi_v7_defconfig
for v4.6 merge window:
- Enable IOMMU and omap3isp so we can enable TVP5150/1 video
decoder
- Enable at24 eeprom for revision detection on beagle-x15
- Enable LP872x regulator for both omap2plus_defconfig and
multi_v7_defconfig as it's needed at least by LG Optimus
Black
* tag 'omap-for-v4.6/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: multi_v7_defconfig: Enable LP872x regulator support
ARM: omap2plus_defconfig: Enable LP872x regulator support
ARM: omap2plus_defconfig: Enable AT24 eeprom
ARM: omap2plus_defconfig: Enable TI TVP5150 video decoder support
ARM: omap2plus_defconfig: Enable ISP support and dependencies
ARM: omap2plus_defconfig: Enable OMAP IOMMU support
The LP872x regulator is used in the LG Optimus Black codename sniper to supply
the external mmc card.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AT24 compatible eeproms are used in BB family and X15 boards.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Many OMAP3 boards have a TVP5150/1 video decoder attached to the OMAP3
ISP so enable support for its driver as a module to be able to test it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 SoC has a Image Signal Processor (ISP) that's used to accelerate
camera images processing. The ISP driver implements V4L2, Media Controller
and V4L2 sub-dev interfaces so enable support for the driver and all these
dependencies to allow video capture to be tested using this HW IP block.
Also, disable the I2C ancillary drivers auto-select option since the media
driver does not auto-select the ancillary devices that are attached to the
bridge because this depends on what's present in the supported OMAP boards.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3 media platform drivers (i.e: omap3isp) needs IOMMU support so
enable it to be able to test the OMAP3 Image Signal Processor (ISP).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull fbdev fixes from Tomi Valkeinen:
- fix omap2plus_defconfig to enable omapfb as it was in v4.4
- ocfb: fix timings for margins
- s6e8ax0, da8xx-fb: fix compile warnings
- mmp: fix build failure caused by bad printk parameters
- imxfb: fix clock issue which kept the display off
* tag 'fbdev-fixes-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux:
video: fbdev: imxfb: Provide a reset mechanism
fbdev: mmp: print IRQ resource using %pR format string
fbdev: da8xx-fb: remove incorrect type cast
fbdev: s6e8ax0: avoid unused function warnings
ocfb: fix tgdel and tvdel timing parameters
ARM: omap2plus_defconfig: update display configs
omapfb and omapdrm were recently made independent of each other, and
this required Kconfig option changes. This patch changes the
omap2plus_defconfig to enable display similarly as before: omapfb and
panel & encoder drivers as modules.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
With recent omap assembly fixes for CONFIG_DEBUG_RODATA, we can
now use DEBUG_RODATA. Let's enable ARM_KERNMEM_PERMS so that
DEBUG_RODATA gets selected by default. This way we can make sure
any related issues are caught early.
And while testing things on various devices, I noticed we're
missing few loadable modules to make things more usable:
- USB Ethernet for smsc75xx, we only have smsc97xx right now
- Basic USB serial drivers for things like ftdi and pl2303 ports
- Blinking leds with pca963x
Signed-off-by: Tony Lindgren <tony@atomide.com>
CONFIG_DEBUG_INFO_SPLIT will split debug info on
.dwo files. This will generate a smaller vmlinux and
smaller .ko modules, which will be easier to ship on
certain products.
CONFIG_DEBUG_INFO_DWARF4 will generate debug info in
DWARF4 format, which ends up being larger, but
improves the probability of resolving variables in
optmized code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: this makes initramfs quite a bit smaller]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This enables tca6424a GPIO expander driver that in turn enables
TPD12S015 HDMI ESD protection and level shifter on OMAP5 uevm.
In other words, it makes HDMI work on OMAP5 uevm.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
One of the lines from PCF857x is connected to the vdd line of MMC1
in DRA74x and DRA72x EVMs and is modelled as a regulator. If PCF857x
is not made as built-in, the regulator_get in omap_hsmmc fails making
it difficult to use MMC1 as rootfs.
Make PCF857x built-in.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With recent MUSB changes we can now build in support for multiple
DMA implementations. So let's enable DMA by default to make life
easier for distro use.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC defconfig updates from Olof Johansson:
"We mostly keep defconfigs updates on a separate branch due to their
tendency to conflict between platforms and this encourages more
careful separation of code changes and config changes.
Most updates here are minor tweaks, enabling new drivers for various
platforms, and so on. Renesas also removed one defconfig
(marzen_defconfig)"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: add TC2 PM support to multi_v7_defconfig
ARM: tegra: Update multi_v7_defconfig
ARM: tegra: Update default configuration
ARM: at91/defconfig: at91_dt: remove ARM_AT91_ETHER
ARM: at91/defconfig: at91_dt: enable DRM hlcdc support
ARM: at91: at91_dt_defconfig: enable ISI and ov2640 support
ARM: multi_v7_defconfig: Enable Allwinner P2WI, PWM, DMA_SUN6I, cryptodev
ARM: sunxi_defconfig: Enable DMA_SUN6I, P2WI, PWM, cryptodev, EXTCON, FHANDLE
ARM: shmobile: Enable fixed voltage regulator in shmobile_defconfig
ARM: multi_v7_defconfig: Select MX6UL and MX7D
ARM: prima2_defconfig: enable build for hwspinlock
ARM: prima2_defconfig: enable build for RTC
ARM: prima2_defconfig: enable build for misc input
ARM: prima2_defconfig: enable build for SiRFSoC SDHC host
ARM: prima2_defconfig: fix the outdated defconfig
ARM: imx_v6_v7_defconfig: Select CONFIG_IKCONFIG_PROC
ARM: defconfig: orion5x: add DT support
ARM: qcom_defconfig: Enable options for KS8851 ethernet
ARM: multi_v7_defconfig: Enable support for PWM Regulators
ARM: multi_v7_defconfig: Enable ST's PWM driver
...
M25P80 driver provides support for most common SPI NOR devices.
These devices are commonly found on TI EVMs for AM437x and DRA7x
SoCs.
Enable support for this driver in defconfig for omap2plus devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CPTS module of CPSW IP enables timestamp synchronization
using PTP. Enable CPTS feature of CPSW driver.
Available on AM335x, AM437x and DRA7x SoCs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for on-chip resistive touchscreen m found on AM335x and
AM437x devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable support for on-chip ADC found on AM335x and
AM437x devices.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
More and more boards are moving to have audio support via simple-card.
At the same time enable options needed for most am335x and am43xx board for
audio support: McASP and TLV320AIC3X codecs.
The later two has been selected by the CONFIG_SND_AM33XX_SOC_EVM option, but
the aim is to convert all boards to use simple card.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Few omap2plus_defconfig changes for v4.2 merge window:
- Enable dm9000 as built-in for NFSroot
- Enable dm816x USB phy as a loadable module
- Enable Pixcir touch screen as a loadable module
* tag 'omap-for-v4.2/o2_dc' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable TOUCHSCREEN_PIXCIR
ARM: omap2plus_defconfig: Add dm816x USB PHY as a loadable module
ARM: omap2plus_defconifg: Enable DM9000 in omap2plus_defconfig
Some of the OMAP based boards e.g. am437x-gp-evm have
the Pixcir touch controller. Enable the related device
driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
