Along with 5 TX queues, 5 RX queues are allocated at the beginning of
device probe. However, only the real number of TX queues is set. Configure
the real number of RX queues as well.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards [1] leave the PHYs at an invalid state
during system power-up or reset thus causing unreliability
issues with the PHY which manifests as PHY not being detected
or link not functional. To fix this, these PHYs need to be RESET
via a GPIO connected to the PHY's RESET pin.
Some boards have a single GPIO controlling the PHY RESET pin of all
PHYs on the bus whereas some others have separate GPIOs controlling
individual PHY RESETs.
In both cases, the RESET de-assertion cannot be done in the PHY driver
as the PHY will not probe till its reset is de-asserted.
So do the RESET de-assertion in the MDIO bus driver.
[1] - am572x-idk, am571x-idk, a437x-idk
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "skb" to get "skb->len" so we should probably do that
step before freeing the skb.
Fixes: eea221ce48 ("tc35815 driver update (take 2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add vsockmon virtual network device that receives packets from the vsock
transports and exposes them to user space.
Based on the nlmon device.
Signed-off-by: Gerard Garcia <ggarcia@deic.uab.cat>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.12
Quite a lot of patches for rtlwifi and iwlwifi this time, but changes
also for other active wireless drivers.
Major changes:
ath9k
* add support for Dell Wireless 1601 PCI device
* add debugfs file to manually override noise floor
ath10k
* bump up FW API to 6 for a new QCA6174 firmware branch
wil6210
* support 8 kB RX buffers
iwlwifi
* work to support A000 devices continues
* add support for FW API 30
* add Geographical and Dynamic Specific Absorption Rate (SAR) support
* support a few new PCI device IDs
rtlwifi
* work on adding Bluetooth coexistance support, not finished yet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for static/local dcbx mode. In this mode
adapter brings up the dcbx link with locally configured parameters
instead of performing the dcbx negotiation with the peer. The feature
is useful when peer device/switch doesn't support dcbx.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the older firmware there was no distinction between RoCE and RoCEv2
whereas the newer firmware (8.15.3.0) allows us to configure each
independently. Driver need to populate the RoCEv2 data in its specific
structure.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have observed a sudden spike in rx/tx_packets and rx/tx_bytes
reported under /proc/net/dev. There is a race in mlx5e_update_stats()
and some of the get-stats functions (the one that we hit is the
mlx5e_get_stats() which is called by ndo_get_stats64()).
In particular, the very first thing mlx5e_update_sw_counters()
does is 'memset(s, 0, sizeof(*s))'. For example, if mlx5e_get_stats()
is unlucky at one point, rx_bytes and rx_packets could be 0. One second
later, a normal (and much bigger than 0) value will be reported.
This patch is to use a 'struct mlx5e_sw_stats temp' to avoid
a direct memset zero on priv->stats.sw.
mlx5e_update_vport_counters() has a similar race. Hence, addressed
together. However, memset zero is removed instead because
it is not needed.
I am lucky enough to catch this 0-reset in rx multicast:
eth0: 41457665 76804 70 0 0 70 0 47085 15586634 87502 3 0 0 0 3 0
eth0: 41459860 76815 70 0 0 70 0 47094 15588376 87516 3 0 0 0 3 0
eth0: 41460577 76822 70 0 0 70 0 0 15589083 87521 3 0 0 0 3 0
eth0: 41463293 76838 70 0 0 70 0 47108 15595872 87538 3 0 0 0 3 0
eth0: 41463379 76839 70 0 0 70 0 47116 15596138 87539 3 0 0 0 3 0
v2: Remove memset zero from mlx5e_update_vport_counters()
v1: Use temp and memcpy
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-04-20
This series contains updates to e1000, e1000e, igb/vf and ixgb.
Tobias Klauser cleans up e1000, ixgb and igbvf from having a local
function or structure for netdev stats.
Bernd Faust fixes an issue for 82579 devices, where the clock frequency
was being incorrectly set for these devices. These devices only support
96MHz, so make sure they are set to use only that.
Yury Kylulin extends the work Jake and Alex did for ixgbe in MAC filter
handling into the igb driver.
Kim Tatt Chuah enables igb to wake up by packet and to read the necessary
Wake Up Status (WUS) and Wake Up Packet Memory (WUPM) registers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
RX packet headers are meant to be contained in SKB linear part,
and chose a threshold of 128.
It turns out this is not enough, i.e. for IPv6 packet over VxLAN.
In this case, UDP/IPv4 needs 42 bytes, GENEVE header is 8 bytes,
and 86 bytes for TCP/IPv6. In total 136 bytes that is more than
current 128 bytes. In this case expand header flow is reached.
The warning in skb_try_coalesce() caused by a wrong truesize
was already fixed here:
commit 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()").
Still, we prefer to totally avoid the expand header flow for performance reasons.
Tested regular TCP_STREAM with iperf for 1 and 8 streams, no degradation was found.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When UAR is released, we deallocate the device resource, but
don't unmmap the UAR mapping memory.
Fix the leak by unmapping this memory.
Fixes: a6d51b6861 ('net/mlx5: Introduce blue flame register allocator)
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv6 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv4 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On ConnectX5 the wqe inline mode is "none" and hence the FW
reports MLX5_CAP_INLINE_MODE_NOT_REQUIRED.
Fix our devlink callbacks to deal with that on get and set.
Also fix the tc flow parsing code not to fail anything when
inline isn't required.
Fixes: bffaa91658 ('net/mlx5: E-Switch, Add control for inline mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If FW is stuck in initializing state we will skip the driver load, but
current error handling flow doesn't clean previously allocated command
interface resources.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warning about missing prototypes. The rx/tx code path
defines functions with prototypes in ipoib.h.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix sparse warnings in recent ipoib support.
The RDMA functions are not used yet, hide behind #ifdef.
Based on comment, they will eventually be local so make static.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Implement the devlink e-switch encapsulation control set and get
callbacks. Apply the value set by the user on the switchdev offloads
mode when creating the fast FDB table where offloaded rules will be set.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Refactor the creation of the fast path FDB table that holds the
offloaded rules in SRIOV switchdev mode into it's own function.
This will be used in the next patch to be able and re-create the
table under different settings without going through legacy mode.
This patch doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
A device driver must not select the COMMON_CLK subsystem, as that conflicts
with platforms that provide a legacy implementation of the clk API:
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-sa1100/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
drivers/clk/clk.o: In function `clk_round_rate':
clk.c:(.text.clk_round_rate+0x0): multiple definition of `clk_round_rate'
arch/arm/mach-sa1100/clock.o:clock.c:(.text.clk_round_rate+0x0): first defined here
drivers/clk/clk.o: In function `clk_get_parent':
clk.c:(.text.clk_get_parent+0x0): multiple definition of `clk_get_parent'
arch/arm/mach-sa1100/clock.o:clock.c:(.text.clk_get_parent+0x0): first defined here
drivers/clk/clk.o: In function `clk_get_rate':
clk.c:(.text.clk_get_rate+0x0): multiple definition of `clk_get_rate'
This changes the 'select' into 'depends on', as all other similar drivers do.
Fixes: d931acd575d6 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both conflict were simple overlapping changes.
In the kaweth case, Eric Dumazet's skb_cow() bug fix overlapped the
conversion of the driver in net-next to use in-netdev stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_I2C=m and NET_DSA_SMSC_LAN9303=y, we run into a link error:
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_read':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_read+0x18): undefined reference to `i2c_smbus_read_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_byte_reg_write':
regmap-i2c.c:(.text.regmap_smbus_byte_reg_write+0x18): undefined reference to `i2c_smbus_write_byte_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_reg_read':
regmap-i2c.c:(.text.regmap_smbus_word_reg_read+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_read_swapped':
regmap-i2c.c:(.text.regmap_smbus_word_read_swapped+0x18): undefined reference to `i2c_smbus_read_word_data'
drivers/base/regmap/regmap-i2c.o: In function `regmap_smbus_word_write_swapped':
This adds a Kconfig dependency to avoid the broken configuration.
Fixes: be4e119f99 ("net: dsa: LAN9303: add I2C managed mode support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier patch 4493b81bea ("bonding: initialize work-queues during
creation of bond") moved the work-queue initialization from bond_open()
to bond_create(). However this caused the link those are created using
netlink 'create bond option' (ip link add bondX type bond); create the
new trunk without initializing work-queues. Prior to the above mentioned
change, ndo_open was in both paths and things worked correctly. The
consequence is visible in the report shared by Joe Stringer -
I've noticed that this patch breaks bonding within namespaces if
you're not careful to perform device cleanup correctly.
Here's my repro script, you can run on any net-next with this patch
and you'll start seeing some weird behaviour:
ip netns add foo
ip li add veth0 type veth peer name veth0+ netns foo
ip li add veth1 type veth peer name veth1+ netns foo
ip netns exec foo ip li add bond0 type bond
ip netns exec foo ip li set dev veth0+ master bond0
ip netns exec foo ip li set dev veth1+ master bond0
ip netns exec foo ip addr add dev bond0 192.168.0.1/24
ip netns exec foo ip li set dev bond0 up
ip li del dev veth0
ip li del dev veth1
The second to last command segfaults, last command hangs. rtnl is now
permanently locked. It's not a problem if you take bond0 down before
deleting veths, or delete bond0 before deleting veths. If you delete
either end of the veth pair as per above, either inside or outside the
namespace, it hits this problem.
Here's some kernel logs:
[ 1221.801610] bond0: Enslaving veth0+ as an active interface with an up link
[ 1224.449581] bond0: Enslaving veth1+ as an active interface with an up link
[ 1281.193863] bond0: Releasing backup interface veth0+
[ 1281.193866] bond0: the permanent HWaddr of veth0+ -
16:bf:fb:e0:b8:43 - is still in use by bond0 - set the HWaddr of
veth0+ to a different address to avoid conflicts
[ 1281.193867] ------------[ cut here ]------------
[ 1281.193873] WARNING: CPU: 0 PID: 2024 at kernel/workqueue.c:1511
__queue_delayed_work+0x13f/0x150
[ 1281.193873] Modules linked in: bonding veth openvswitch nf_nat_ipv6
nf_nat_ipv4 nf_nat autofs4 nfsd auth_rpcgss nfs_acl binfmt_misc nfs
lockd grace sunrpc fscache ppdev vmw_balloon coretemp psmouse
serio_raw vmwgfx ttm drm_kms_helper vmw_vmci netconsole parport_pc
configfs drm i2c_piix4 fb_sys_fops syscopyarea sysfillrect sysimgblt
shpchp mac_hid nf_conntrack_ipv6 nf_defrag_ipv6 nf_conntrack_ipv4
nf_defrag_ipv4 nf_conntrack libcrc32c lp parport hid_generic usbhid
hid mptspi mptscsih e1000 mptbase ahci libahci
[ 1281.193905] CPU: 0 PID: 2024 Comm: ip Tainted: G W
4.10.0-bisect-bond-v0.14 #37
[ 1281.193906] Hardware name: VMware, Inc. VMware Virtual
Platform/440BX Desktop Reference Platform, BIOS 6.00 09/30/2014
[ 1281.193906] Call Trace:
[ 1281.193912] dump_stack+0x63/0x89
[ 1281.193915] __warn+0xd1/0xf0
[ 1281.193917] warn_slowpath_null+0x1d/0x20
[ 1281.193918] __queue_delayed_work+0x13f/0x150
[ 1281.193920] queue_delayed_work_on+0x27/0x40
[ 1281.193929] bond_change_active_slave+0x25b/0x670 [bonding]
[ 1281.193932] ? synchronize_rcu_expedited+0x27/0x30
[ 1281.193935] __bond_release_one+0x489/0x510 [bonding]
[ 1281.193939] ? addrconf_notify+0x1b7/0xab0
[ 1281.193942] bond_netdev_event+0x2c5/0x2e0 [bonding]
[ 1281.193944] ? netconsole_netdev_event+0x124/0x190 [netconsole]
[ 1281.193947] notifier_call_chain+0x49/0x70
[ 1281.193948] raw_notifier_call_chain+0x16/0x20
[ 1281.193950] call_netdevice_notifiers_info+0x35/0x60
[ 1281.193951] rollback_registered_many+0x23b/0x3e0
[ 1281.193953] unregister_netdevice_many+0x24/0xd0
[ 1281.193955] rtnl_delete_link+0x3c/0x50
[ 1281.193956] rtnl_dellink+0x8d/0x1b0
[ 1281.193960] rtnetlink_rcv_msg+0x95/0x220
[ 1281.193962] ? __kmalloc_node_track_caller+0x35/0x280
[ 1281.193964] ? __netlink_lookup+0xf1/0x110
[ 1281.193966] ? rtnl_newlink+0x830/0x830
[ 1281.193967] netlink_rcv_skb+0xa7/0xc0
[ 1281.193969] rtnetlink_rcv+0x28/0x30
[ 1281.193970] netlink_unicast+0x15b/0x210
[ 1281.193971] netlink_sendmsg+0x319/0x390
[ 1281.193974] sock_sendmsg+0x38/0x50
[ 1281.193975] ___sys_sendmsg+0x25c/0x270
[ 1281.193978] ? mem_cgroup_commit_charge+0x76/0xf0
[ 1281.193981] ? page_add_new_anon_rmap+0x89/0xc0
[ 1281.193984] ? lru_cache_add_active_or_unevictable+0x35/0xb0
[ 1281.193985] ? __handle_mm_fault+0x4e9/0x1170
[ 1281.193987] __sys_sendmsg+0x45/0x80
[ 1281.193989] SyS_sendmsg+0x12/0x20
[ 1281.193991] do_syscall_64+0x6e/0x180
[ 1281.193993] entry_SYSCALL64_slow_path+0x25/0x25
[ 1281.193995] RIP: 0033:0x7f6ec122f5a0
[ 1281.193995] RSP: 002b:00007ffe69e89c48 EFLAGS: 00000246 ORIG_RAX:
000000000000002e
[ 1281.193997] RAX: ffffffffffffffda RBX: 00007ffe69e8dd60 RCX: 00007f6ec122f5a0
[ 1281.193997] RDX: 0000000000000000 RSI: 00007ffe69e89c90 RDI: 0000000000000003
[ 1281.193998] RBP: 00007ffe69e89c90 R08: 0000000000000000 R09: 0000000000000003
[ 1281.193999] R10: 00007ffe69e89a10 R11: 0000000000000246 R12: 0000000058f14b9f
[ 1281.193999] R13: 0000000000000000 R14: 00000000006473a0 R15: 00007ffe69e8e450
[ 1281.194001] ---[ end trace 713a77486cbfbfa3 ]---
Fixes: 4493b81bea ("bonding: initialize work-queues during creation of bond")
Reported-by: Joe Stringer <joe@ovn.org>
Tested-by: Joe Stringer <joe@ovn.org>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently driver use phy_start_aneg() in arc_emac_open() to bring
up PHY. But phy_start() function is more appropriate for this purposes.
Besides that it call phy_start_aneg() as part of PHY startup sequence
it also can correctly bring up PHY from error and suspended states.
So the patch replace phy_start_aneg() to phy_start().
Also the patch add call to phy_stop() to arc_emac_stop() to allow
the PHY device to be fully suspended when the interface is unused.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-04-19
This series contains updates to i40e and i40evf only, most notable being
the addition of trace points for BPF programs.
Tobias Klauser updates i40evf to use net_device stats struct instead
of a local private copy.
Preethi updates the VF driver to not enable receive checksum offload by
default for tunneled packets.
Alex fixes an issue he introduced when he converted the code over to
using the length field to determine if a descriptor was done or not.
Mitch adds the ability to dump additional information on the VFs, which
is not available through 'ip link show' using debugfs.
Scott adds trace points to the drivers so that BPF programs can be
attached for feature testing and verification.
Jingjing adds admin queue functions for Pipeline Personalization Profile
commands.
Jake does most of the heavy lifting in this series, starting with the
a reduction in the scope of the RTNL lock being held while resetting VFs
to allow multiple PFs to reset in a timely manner. Factored out the
direct queue modification so that we are able to re-use the code.
Reduced the wait time for admin queue commands to complete, since we were
waiting a minimum of a millisecond, when in practice the admin queue
command is processed often much faster. Cleaned up code (flag) we never
use. Make the code to resetting all the VFs optimized for parallel
computing instead of the current way is a serialized fashion, to help
reduce the time it takes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The NAPI data structure is embedded in the netvsc_device structure
and is freed when device is closed. There is still a reference
(in NAPI list) to this which causes a crash in netif_napi_del
when device is removed. Fix by managing NAPI instances correctly.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will not be able to send packets over a channel that has been
rescinded. Make necessary adjustments so we can properly cleanup
even when the channel is rescinded. This issue can be trigerred
in the NIC hot-remove path.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bounce buffer is not used in the ibmvnic driver, just
get rid of it.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the allocation of memory for the sub crq structs and their
associated pages to allocate zero-filled memory.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not be releasing the crq's when calling close for the
adapter, these need to remain open to facilitate operations such
as updating the mac address. The crq's should be released in the
adpaters remove routine.
Additionally, we need to call release_reources from remove. This
corrects the scenario of trying to remove an adapter that has only
been probed.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inflight list used to track memory that is allocated for crq that are
inflight is not needed. The one piece of the inflight list that does need
to be cleaned at module exit is the error buffer list which is already
attached to the adapter struct.
This patch removes the inflight list and moves checking the error buffer
list to ibmvnic_remove.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the primary CRQ is only used for service functions and
not in the performance path, simplify the code a bit and avoid
disabling the IRQ.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace a couple of modifications of an atomic followed
by a read of the atomic, which is no longer atomic, to
use atomic_XX_return variants to avoid race conditions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure we unregister long term buffers from the adapter
prior to DMA unmapping it and freeing the buffer. Failure
to do so could result in a DMA to a now invalid address.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibmvnic_change_mac_addr struct alignment was not matching the defined
format in PAPR+, it had the reserved and return code fields swapped. As a
consequence, the CHANGE_MAC_ADDR_RSP commands were being improperly handled
and executed even when the operation wasn't successfully completed by the
system firmware.
Also changing the endianness of the debug message to make it easier to
parse the CRQ content.
Signed-off-by: Murilo Fossa Vicentini <muvic@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out an useless assignment that was added during code refactoring:
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c: In function 'octnet_intrmod_callback':
drivers/net/ethernet/cavium/liquidio/lio_ethtool.c:1315:59: error: parameter 'oct_dev' set but not used [-Werror=unused-but-set-parameter]
This is harmless but can clearly be remove to avoid the warning.
Fixes: 50c0add534 ("liquidio: refactor interrupt moderation code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use skb_cow_head() to properly deal with clones,
especially the ones coming from TCP stack that allow their head being
modified. This avoids a copy.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 4a476bd6d1 ("usbnet: New driver for QinHeng CH9200 devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: 55d7de9de6 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: c9b37458e9 ("USB2NET : SR9700 : One chip USB 1.1 USB2NET SR9700Device Driver Support")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: cc28a20e77 ("introduce cx82310_eth: Conexant CX82310-based ADSL router USB ethernet driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to ensure there is enough headroom to push extra header,
but we also need to check if we are allowed to change headers.
skb_cow_head() is the proper helper to deal with this.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Hughes <james.hughes@raspberrypi.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a critical issue to map txqid with flows on the hardware appropriately,
if tx queues created are more than flows configured then txqid shall map within
the range of hardware flows configured. This ensure that un-mapped txqid does not remain un-handled.
The patch also segregated the rxqid and txqid for clarity.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Reviewed-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As per comment, the code has always been GPLv2 licensed.
This fixes the follwoing modpost warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/broadcom/sb1250-mac.o
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
