To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.
Verified using two terminals:
Terminal 1 Terminal 2
-------------------------- ---------------------------------
# ip netns add brcm-wifi # iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x1
# ip netns exec brcm-wifi bash
# iw dev
# echo $$
20337 # iw phy0 set netns 20337
# iw dev
phy#0
Interface wlan3
ifindex 11
wdev 0x2
# iw phy0 interface add wl3.ap type __ap
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x3
Interface wlan3
ifindex 11
wdev 0x2
# iw dev
# iw phy0 set netns 1
# iw dev
# iw dev
phy#0
Interface wl3.ap
ifindex 2
wdev 0x5
Interface wlan3
ifindex 11
wdev 0x4
Note:
increasing wdev identifier above indicates issue in
cfg80211 which is addressed separately.
Tested-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Chip goes into low power state when this feature is enabled.
This was already enabled for SDIO and PCIe interface based
chipsets.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB firmware added support for sending command response/event through
interrupt endpoint, to enhance RX throughput. Added corresponding changes
required to support this feature. This change takes care of backward
compatibility with older firmware.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For quite some time now brcmfmac supports 802.11ac chipsets and it's
not limited to embedded devices only. There are even standalone PCIe
cards based on BCM43602 or BCM4366.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate line
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Symbolic permissions 'S_IRUSR' are not preferred.
Consider using octal permissions '0400'.
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix output from checkpatch.pl like:
Block comments use a trailing */ on a separate lin
Signed-off-by: Marcin Rokicki <marcin.rokicki@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to fix TPC stats to display the stats
properly. Here cosmetic change has been done to print the
TPC stats for all the cases 1.CDD 2.STBC 3.TXBF
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove obselete Copy Engine comments referring to the function
ath10k_ce_sendlist_send as this function was removed long time back
by the commit 2e761b5a52 ("ath10k: remove ce_sendlist_send").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an ath10k HTC debug message when insufficient tx credits
are available to send the WMI commands. This is very useful
in debugging issues like 'tx credit starvation' that could
possibly happen with multiclient setup with constant roaming
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It seems set_coverage_class_work is not cancelled anywhere,
though I could not find a crash/warning with this existing
design, its safer to cancel it during stop() and also before
restarting the hardware.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If station advertises diffferent NSS capabilities in Rx_mcs set
of HT and VHT IEs in assoc req, the current NSS computation
logic configures the NSS support only based on Rx_mcs set of
HT capabilities in the driver. This is configuring the station
NSS capabilities incorreclty in the target.
For example, if station advertise Rx_mcs set as 2 spatial streams
in HT capabilities and 1 spatial streams in VHT capabilities in
assoc request, as per current logic we are calculating nss from
HT capabilities and the driver sets peer_num_spatial_streams as
2 for the station which is configured in VHT 1*1.
This patchs fix this issue by calculating the nss from VHT cap if
station supports vht.
Signed-off-by: Venkateswara Rao Naralasetty <c_vnaral@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Fixes: 36bcce4306 ("ath9k_htc: Handle storage devices")
Cc: stable <stable@vger.kernel.org> # 2.6.39+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move NAPI enable to 'ath10k_ahb_hif_start' from
'ath10k_ahb_hif_power_up'. This is to maintain the symmetry
of calling napi_enable() from ath10k_ahb_hif_start() so that it
matches with napi_disable() being called from ath10k_pci_hif_stop().
This change is based on the crash fix from Kalle for PCI interface in
commit 1427228d58 ("ath10k: fix napi crash during rmmod when probe
firmware fails").
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.12. Major changes:
ath10k
* improve firmware download time for QCA6174 and QCA9377, especially
helps resume time
ath9k_htc
* add support AirTies 1eda:2315 AR9271 device
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled
rtlwifi
* fix scheduling while atomic regression
brcmfmac
* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().
To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.
This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.
_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.
Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.
Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers fixes for 4.11
iwlwifi
* an RCU fix
* a fix for a potential out-of-bounds access crash
* a fix for IBSS which has been broken since DQA was enabled
rtlwifi
* fix scheduling while atomic regression
brcmfmac
* fix use-after-free bug found by KASAN
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, the rcar_can driver prints:
rcar_can e6e80000.can: device registered (regs @ e08bc000, IRQ76)
The "regs" value is a virtual address, exposing internal information,
hence stop printing it. The (useful) physical address is already
printed as part of the device name.
Fixes: fd1159318e ("can: add Renesas R-Car CAN driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds support for the Holt HI-311x CAN controller. The HI311x
CAN controller is capable of transmitting and receiving standard data
frames, extended data frames and remote frames. The HI311x interfaces
with the host over SPI.
Datasheet: www.holtic.com/documents/371-hi-3110_v-rev-jpdf.do
Signed-off-by: Akshay Bhat <nodeax@gmail.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts TI HECC driver to DT only driver. This results in
removing ti_hecc.h containing now obsolete platform data.
Former transceiver_switch callback function will be now modelled via
regulator API.
Signed-off-by: Anton Glukhov <anton.a.glukhov@gmail.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As RoCE doesn't need to use the SRC, allocating ILT memory
on behalf of RoCE is wasting available ILT lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today there's no protocol supported that requires
support from the TM hardware block and enables SRIOV,
but we should still correct the calculation to reflect
the lines required for such future VFs instead of changing
the PF's own lines.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring the HW timers block we should set the number of CIDs
up until the last CID that require timers, instead of only those CIDs
whose protocol needs timers support.
Today, the protocols that require HW timers' support have their CIDs
before any other protocol, but that would change in future [when we
add iWARP support].
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor and clean up the queue manager initialization logic.
Also, this adds support for RoC low latency queues, which later
would be used for improving RoCE latency in high throughput scenarios.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the net stats64 counters to the usbnet core. With that
in place put the hooks into every usbnet driver to use it.
This is a strait forward addition of 64bit counters for RX and TX packet
and byte counts. It is done in the same style as for the other net drivers
that support stats64. Note that the other stats fields remain as 32bit
sized values (error counts, etc).
The motivation to add this is that it is not particularly difficult to
get the RX and TX byte counts to wrap on 32bit platforms.
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Breaking the include loop netdevice.h, dsa.h, devlink.h broke this
driver, it depends on includes brought in by these headers. Adding
linux/of.h fixes it.
Fixes: ed0e39e97d34 ("net: break include loop netdevice.h, dsa.h, devlink.h")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an incoming frame is tagged or when GRO is disabled, the skb
handled to vxlan_xmit() doesn't contain a valid transport header
offset. This makes ND proxying fail.
We combine two changes: replace use of skb_transport_offset() and ensure
the necessary amount of skb is linear just before using it:
- In vxlan_xmit(), when determining if we have an ICMPv6 neighbor
discovery packet, just check if it is an ICMPv6 packet and rely on
neigh_reduce() to do more checks if this is the case. The use of
pskb_may_pull() is replaced by skb_header_pointer() for just the IPv6
header.
- In neigh_reduce(), add pskb_may_pull() for IPv6 header and neighbor
discovery message since this was removed from vxlan_xmit(). Replace
skb_transport_header() with ipv6_hdr() + 1.
- In vxlan_na_create(), replace first skb_transport_offset() with
ipv6_hdr() + 1 and second with skb_network_offset() + sizeof(struct
ipv6hdr). Additionally, ensure we pskb_may_pull() the whole skb as we
need it to iterate over the options.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some checkpatch.pl script caught errors and
warnings during the compilation time.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a bug on Hip06 that tx ring interrupts packets count will be
clear when drivers send data to tx ring, so that the tx packets count
will never upgrade to packets line, and cause the interrupts engendered
was delayed.
Sometimes, it will cause sending performance lower than expected.
To fix this bug, we set tx ring interrupts packets line to 1 forever,
to avoid count clear. And set the gap time to 20us, to solve the problem
that too many interrupts engendered when packets line is 1.
This patch could advance the send performance on ARM from 6.6G to 9.37G
when an iperf send thread on ARM and an iperf send thread on X86 for XGE.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS needs SMB Buffers to store at least two packets after sending
pause frame because of the link delay. The MTU of HNS is 9728. As
the processor user manual described, the SBM buffer threshold should
be modified.
Reported-by: Ping Zhang <zhangping5@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions (hns_dsaf_set_mac_mc_entry() and hns_mac_del_mac()) are
not called by any functions. They are dead code in hns. And the same
features are implemented by the patch (the id is 66355f5).
Reported-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_lock is a global spin lock, it will take affect
in all rings in the netdevice. In tx_poll_one process, it can
only lock the current ring, in this case, we define a spin lock
in hnae_ring struct for it.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because buf_size of ring set to 2048, the process of rx_poll_one
can reuse the page, therefore the performance of XGE can improve.
But the chip only supports three bds in one package, so the max mtu
is 6K when it sets to 2048. For better performane in litter mtu, we
need change buf_size according to mtu.
When user change mtu, hns is only change the desc in memory. There
are some desc has been fetched by the chip, these desc can not be
changed by the code. So it needs set the port loopback and send
some packages to let the chip consumes the wrong desc and fetch new
desc.
Because the Pv660 do not support rss indirection, we need add version
check in mtu change process.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After polling less than buget packages, we need check again. If
there are still some packages, we call napi_schedule add softirq
queue, this is not better way. So we return buget value instead
of napi_schedule.
Signed-off-by: lipeng <lipeng321@huawei.com>
reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because all members of desc_cb is assigned when xmit one package, so it
can delete in hnae_free_buffer, as follows:
- "dma, priv, length, type" are assigned in fill_v2_desc.
- "page_offset, reuse_flag, buf" are not used in tx direction.
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Weiwei Deng <dengweiwei@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
