Adds a newer videobuf-vmalloc module. This module uses the same
videobuf controls, but implements memory allocation based on vmalloc
methods.
With this method, an USB driver can use video-buf, without needing to
request memory from the DMA-safe area.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
PCI-dependent videobuf_foo methods were renamed as videobuf_pci_foo.
Also, videobuf_dmabuf is now part of videobuf-dma-sg private struct.
So, to access it, a subroutine call is needed.
This patch renames all occurences of those function calls to be
consistent with the video-buf split.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
video-buf currently does two different tasks:
- Manages video buffers with a common code that allows
implementing all the V4L2 different modes of buffering;
- Controls memory allocations
While the first task is generic, the second were written to support PCI DMA
Scatter/Gather needs. The original approach can't even work for those
video capture hardware that don't support scatter/gather.
I did one approach to make it more generic. While the approach worked
fine for vivi driver, it were not generic enough to handle USB needs.
This patch creates two different modules, one containing the generic
video buffer handling (videobuf-core) and another with PCI DMA S/G.
After this patch, it would be simpler to write an USB video-buf and a
non-SG DMA module.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
http://thread.gmane.org/gmane.comp.video.video4linux/34978/focus=34981
Reviewed-by: Ricardo Cerqueira <v4l@cerqueira.org>
Remove support for g_ext_clk and s_ext_clk. The same functionality is
now handled by g_ifparm.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
vidioc_int_g_ifparm can be used to obtain hardware-specific information
about the interface used by the slave.
Rearrange v4l2-int-device.h as well.
Also remove useless & characters.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed missing buttons in keymap.
- make function names & descriptions more generic,
since this same ir receiver and remote is used in
many FusionHDTV products.
- miscellaneous cleanups.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the built-in IR receiver of the DViCO
Fusion HDTV5 RT GOLD PCI card, using FusionHDTV MCE remote controller.
Signed-off-by: Chaogui Zhang <czhang1974@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The convention for framebuffer devices is to call them xxxfb, not xxx-fb.
Conform to this. Also move the ivtvfb.h header to include/linux: it is a
public header. The FBIO_WAITFORVSYNC ioctl is now also defined in the
ivtvfb.h header, no more need to include matroxfb.h for just this ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The Conexant cx23415 MPEG encoder/decoder supports some unusual pixelformats
for the On-Screen Display. Add new defines to videodev2.h for these formats.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver should now pass the 'busy' state of the device to the cx2341x
module whenever controls are set or tried. -EBUSY will be returned if
the device is busy and the user attempts to modify certain 'dangerous'
controls. It concerns controls that change the audio or video
compression mode and bitrates.
The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy)
to the cx2341x, effectively keeping the old behavior for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add radio support for the Thomson DTT7612 tuner.
This tuner uses a different 1st intermediate frequency than the other radio
tuners supported (a lot of NTSC radio tuners probably need this change too).
Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for
radio reception. The radio frequency setting code in tuner-simple now uses
this field, instead of a special case select() block for each tuner with radio
support.
The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1
in tuner-types.c.
The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and
fm_gain_normal = 1.
Add some defines for tda9887 bits that control IF setting in radio mode.
Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz
radio IF.
Fix the way tda9887 radio options work. The driver was modifying the default
radio mode config templates based on the TDA9887_XXXX flags. This means that
_all_ tuners would get the same settings. If you had a one tuner than used
TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the
tda9987 driver just checks if tuner mode is radio and then applies the config
settings directly to the data being sent, just like how all the TV mode
settings already work.
The PLL setting math is made a little more accurate.
And a grammar error in a printk is fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert av7110_v4l.c to use i2c_transfer() instead of saa7146_i2c_transfer().
Make saa7146_i2c_transfer() static.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is internal to the Panasonic VP27S tuner and is used to set
the mono/stereo/bilingual setting of the tuner.
It is used by two Japanese cx23416-based cards.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up duplicate includes in
include/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a compile warning on non-32-bit machines in v4l2-int-device.h.
Add internal ioctl interface fallback function for ioctls with one
argument.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds an internal ioctl-like interface which can be used in
situations where a single Video4Linux device is implemented by multiple
device drivers. One master device controls one or more slave devices.
The slaves provide Video4Linux ioctl-like interface for the use of the
master.
Only a handful of ioctls are implemented at the moment. More can (and
should) be added as more functionality is required.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Three main sets of changes:
1) dmi_get_system_info() return value should have been marked const,
since callers should not be changing that data.
2) const-ify DMI internals, since DMI firmware tables should,
whenever possible, be marked const to ensure we never ever write to
that data area.
3) const-ify DMI API, to enable marking tables const where possible
in low-level drivers.
And if we're really lucky, this might enable some additional
optimizations on the part of the compiler.
The bulk of the changes are #2 and #3, which are interrelated. #1 could
have been a separate patch, but it was so small compared to the others,
it was easier to roll it into this changeset.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently /proc/locks is shown with a proc_read function, but its behavior
is rather complex as it has to manually handle current offset and buffer
length. On the other hand, files that show objects from lists can be
easily reimplemented using the sequential files and the seq_list_XXX()
helpers.
This saves (as usually) 16 lines of code and more than 200 from
the .text section.
[akpm@linux-foundation.org: no externs in C]
[akpm@linux-foundation.org: warning fixes]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The combination of S_ISGID bit set and S_IXGRP bit unset is used to mark the
inode as "mandatory lockable" and there's a macro for this check called
MANDATORY_LOCK(inode). However, fs/locks.c and some filesystems still perform
the explicit i_mode checking. Besides, Andrew pointed out, that this macro is
buggy itself, as it dereferences the inode arg twice.
Convert this macro into static inline function and switch its users to it,
making the code shorter and more readable.
The __mandatory_lock() helper is to be used in places where the IS_MANDLOCK()
for superblock is already known to be true.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Modify the NFS server code to support 64 bit ino's, as
appropriate for the system and the NFS protocol version.
The gist of the changes is to query the underlying file system
for attributes and not just to use the cached attributes in the
inode. For this specific purpose, the inode only contains an
ino field which unsigned long, which is large enough on 64 bit
platforms, but is not large enough on 32 bit platforms.
I haven't been able to find any reason why ->getattr can't be called
while i_mutex. The specification indicates that i_mutex is not
required to be held in order to invoke ->getattr, but it doesn't say
that i_mutex can't be held while invoking ->getattr.
I also haven't come to any conclusions regarding the value of
lease_get_mtime() and whether it should or should not be invoked
by fill_post_wcc() too. I chose not to change this because I
thought that it was safer to leave well enough alone. If we
decide to make a change, it can be done separately.
Signed-off-by: Peter Staubach <staubach@redhat.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Acked-by: Neil Brown <neilb@suse.de>
We have some slabs that the nfs4 server uses to store state objects.
We're currently creating and destroying those slabs whenever the server
is brought up or down. That seems excessive; may as well just do that
in module initialization and exit.
Also add some minor header cleanup. (Thanks to Andrew Morton for that
and a compile fix.)
Signed-off-by: "J. Bruce Fields" <bfields@citi.umich.edu>
Acked-by: Neil Brown <neilb@suse.de>
This boot parameter will allow legacy 32-bit applications which call stat()
to continue to function even if the NFSv3/v4 server uses 64-bit inode
numbers.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
- NFS_READTIME, NFS_CHANGE_ATTR are completely unused.
- Inline the few remaining uses of NFS_ATTRTIMEO, and remove.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The lower level routines in fs/nfs/proc.c, fs/nfs/nfs3proc.c and
fs/nfs/nfs4proc.c should already be dealing with the revalidation issues.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The fact that we're in the process of modifying the inode does not mean
that we should not invalidate the attribute and data caches. The defensive
thing is to always invalidate when we're confronted with inode
mtime/ctime or change_attribute updates that we do not immediately
recognise.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We don't care about whether or not some other process on our client is
changing the directory while we're in nfs_lookup_revalidate(), because the
dcache will take care of ensuring local atomicity.
We can therefore remove the test for nfs_caches_unstable().
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFSv2 and v4 don't offer weak cache consistency attributes on WRITE calls.
In NFSv3, returning wcc data is optional. In all cases, we want to prevent
the client from invalidating our cached data whenever ->write_done()
attempts to update the inode attributes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NFSv3 will correctly update atime on a readdir call, so there is no need to
set the NFS_INO_INVALID_ATIME flag unless the call to nfs_refresh_inode()
fails.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The reason is that if the weak cache consistency update was successful,
then we know that our client must be the only one that changed the
directory, and we've already updated the dcache to reflect the change.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
We always want to check that the verifier and directory
cache_change_attribute match. This also allows us to remove the 'wraparound
hack' for the cache_change_attribute. If we're only checking for equality,
then we don't care about wraparound issues.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
It doesn't really make sense to cache an access call without also
revalidating the attributes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently, _nfs4_do_access() is just a copy of nfs_do_access() with added
conversion of the open flags into an access mask. This patch merges the
duplicate functionality.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This implements the configuration and building of the core transport
switch implementation of the rpcrdma transport. Stubs are provided for
the rpcrdma protocol handling, and the infiniband/iwarp verbs interface.
These are provided in following patches.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
This file implements the configuration target, protocol template and
constants for the rpcrdma transport framing, for use by the xprtrdma
rpc transport implementation.
Signed-off-by: Tom Talpey <talpey@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
To prepare for including non-sockets-based RPC transports, select
RPC transports by an identifier (to be used in following patches).
Signed-off-by: Tom Talpey <tmt@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
To prepare for including non-sockets-based RPC transports, move the
sockets-dependent definitions into their own file.
Signed-off-by: Tom Talpey <tmt@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
![](/avatar/511417582bfa18e9a88da2ada8339d64?size=56 "\\"Talpey, Thomas\"){kind=small}