This adds new set/get tiling interfaces where the pitch
and macro/micro tiling enables can be set. Along with
a flag to decide if this object should have a surface when mapped.
The only thing we need to allocate with a mapped surface should be
the frontbuffer. Note rotate scanout shouldn't require one, and
back/depth shouldn't either, though mesa needs some fixes.
It fixes the TTM interfaces along Thomas's suggestions, and I've tested
the surface stealing code with two X servers and not seen any lockdep issues.
I've stopped tiling the fbcon frontbuffer, as I don't see there being
any advantage other than testing, I've left the testing commands in there,
just flip the fb_tiled to true in radeon_fb.c
Open: Can we integrate endian swapping in with this?
Future features:
texture tiling - need to relocate texture registers TXOFFSET* with tiling info.
This also merges Michel's cleanup surfaces regs at init time patch
even though it makes sense on its own, this patch really relies on it.
Some PowerMac firmwares set up a tiling surface at the beginning of VRAM
which messes us up otherwise.
that patch is:
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On certain configurations, HPA isn't or can't be unlocked during
probing but it somehow ends up unlocked afterwards. In the following
thread, the problem can be reliably reproduced after resuming from
STR. The BIOS turns on HPA during boot but forgets to do it during
resume.
http://thread.gmane.org/gmane.linux.kernel/858310
This patch updates libata revalidation such that it considers native
n_sectors. If the device size has increased to match native
n_sectors, it's assumed that HPA has been unlocked involuntarily and
the device is recognized as the same one. This should be fairly safe
while nicely working around the problem.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Christof Warlich <christof@warlich.name>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Instead of trying to share the generic 4.1 reply cache code for the
CREATE_SESSION reply cache, it's simpler to handle CREATE_SESSION
separately.
The nfs41 single slot clientid DRC holds the results of create session
processing. CREATE_SESSION can be preceeded by a SEQUENCE operation
(an embedded CREATE_SESSION) and the create session single slot cache must be
maintained. nfsd4_replay_cache_entry() and nfsd4_store_cache_entry() do not
implement the replay of an embedded CREATE_SESSION.
The clientid DRC slot does not need the inuse, cachethis or other fields that
the multiple slot session cache uses. Replace the clientid DRC cache struct
nfs4_slot cache with a new nfsd4_clid_slot cache. Save the xdr struct
nfsd4_create_session into the cache at the end of processing, and on a replay,
replace the struct for the replay request with the cached version all while
under the state lock.
nfsd4_proc_compound will handle both the solo and embedded CREATE_SESSION case
via the normal use of encode_operation.
Errors that do not change the create session cache:
A create session NFS4ERR_STALE_CLIENTID error means that a client record
(and associated create session slot) could not be found and therefore can't
be changed. NFSERR_SEQ_MISORDERED errors do not change the slot cache.
All other errors get cached.
Remove the clientid DRC specific check in nfs4svc_encode_compoundres to
put the session only if cstate.session is set which will now always be true.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
NFSD_SLOT_CACHE_SIZE is the size of all encoded operation responses
(excluding the sequence operation) that we want to cache.
For now, keep NFSD_SLOT_CACHE_SIZE at PAGE_SIZE. It will be reduced
when the DRC is changed from page based to memory based.
Signed-off-by: Andy Adamson <andros@netapp.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
This converts swiotlb to use phys_to_dma and dma_to_phys instead of
swiotlb_phys_to_bus() and swiotlb_bus_to_phys().
swiotlb_phys_to_bus() and swiotlb_bus_to_phys() are not necessary so
this patch also removes them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
is_buffer_dma_capable() was replaced with dma_capable().
is_buffer_dma_capable() tells if a buffer is dma-capable or
not. However, it doesn't take a pointer to struct device so it doesn't
work for POWERPC.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Becky Bruce <beckyb@kernel.crashing.org>
Even though reverse path filter was changed from simple boolean to
trinary control, the loose mode only works if both all and device are
configured because of this logic error.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.infradead.org/users/eparis/notify:
inotify: use GFP_NOFS under potential memory pressure
fsnotify: fix inotify tail drop check with path entries
inotify: check filename before dropping repeat events
fsnotify: use def_bool in kconfig instead of letting the user choose
inotify: fix error paths in inotify_update_watch
inotify: do not leak inode marks in inotify_add_watch
inotify: drop user watch count when a watch is removed
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
net: irda: init spinlock after memcpy
ixgbe: fix for 82599 errata marking UDP checksum errors
r8169: WakeOnLan fix for the 8168
netxen: reset ring consumer during cleanup
net/bridge: use kobject_put to release kobject in br_add_if error path
smc91x.h: add config for Nomadik evaluation kit
NET: ROSE: Don't use static buffer.
eepro: Read buffer overflow
tokenring: Read buffer overflow
at1700: Read buffer overflow
fealnx: Write outside array bounds
ixgbe: remove unnecessary call to device_init_wakeup
ixgbe: Don't priority tag control frames in DCB mode
ixgbe: Enable FCoE offload when DCB is enabled for 82599
net: Rework mdio-ofgpio driver to use of_mdio infrastructure
register at91_ether using platform_driver_probe
skge: Enable WoL by default if supported
net: KS8851 needs to depend on MII
be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
...
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (34 commits)
V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro
V4L/DVB (12302): cx23885-417: fix broken IOCTL handling
V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner
V4L/DVB (12291): b2c2: fix frontends compiled into kernel
V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers
V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header).
V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges.
V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register.
V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app
V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors.
V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1)
V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e
V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used
V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support
V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881)
V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB
V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant)
V4L/DVB (12245): em28xx: add support for mt9m001 webcams
V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format
V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency
...
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm:
dm table: pass correct dev area size to device_area_is_valid
dm: remove queue next_ordered workaround for barriers
dm raid1: wake kmirrord when requeueing delayed bios after remote recovery
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
jbd: fix race between write_metadata_buffer and get_write_access
ext3: Get rid of extenddisksize parameter of ext3_get_blocks_handle()
jbd: Fix a race between checkpointing code and journal_get_write_access()
ext3: Fix truncation of symlinks after failed write
jbd: Fail to load a journal if it is too short
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb()
Upcoming paches to support the new 64-bit "BookE" powerpc architecture
will need to have the virtual address corresponding to PTE page when
freeing it, due to the way the HW table walker works.
Basically, the TLB can be loaded with "large" pages that cover the whole
virtual space (well, sort-of, half of it actually) represented by a PTE
page, and which contain an "indirect" bit indicating that this TLB entry
RPN points to an array of PTEs from which the TLB can then create direct
entries. Thus, in order to invalidate those when PTE pages are deleted,
we need the virtual address to pass to tlbilx or tlbivax instructions.
The old trick of sticking it somewhere in the PTE page struct page sucks
too much, the address is almost readily available in all call sites and
almost everybody implemets these as macros, so we may as well add the
argument everywhere. I added it to the pmd and pud variants for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV]
Acked-by: Nick Piggin <npiggin@suse.de>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. add intel's sdio vendor id to sdio_ids.h
2. move iwmc3200 sdio devices' ids to sdio_ids.h
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've had %pM for long enough now, time to deprecate
print_mac() and remove the __maybe_unused attribute
from DECLARE_MAC_BUF so that variables declared with
that can be found and removed. Otherwise people are
putting in new users of print_mac().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a static buffer in rose2asc() to return its result is not
threadproof and can result in corruption if multiple threads are trying
to use one of the procfs files based on rose2asc().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original isdnhdlc code was developed for devices which had
reversed bitorder in the byte stream. Adding code to handle normal
bitstreams as well.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
isdnhdlc is useful for other ISDN drivers as well.
Move the include file to a central location and the source
to the central isdn location.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
They are not supposed to be modified by drivers, so make them const.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
mac80211 required this due to the master netdev, but now
it can put all information into skb->cb and this can go.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.
For example (from hwsim):
$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
freq: 2462
beacon interval: 100
capability: ESS ShortSlotTime (0x0401)
signal: -50.00 dBm
SSID: j
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Paramater set: channel 11
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In cfg80211_scan_request n_channels refers to the total number
of channels to scan. Update the misleading comment accordingly.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some cleanups of the lockdep code after the BFS series:
- Remove the last traces of the generation id
- Fixup comment style
- Move the bfs routines into lockdep.c
- Cleanup the bfs routines
[ tom.leiming@gmail.com: Fix crash ]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1246201486-7308-11-git-send-email-tom.leiming@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently lockdep will print the 1st circle detected if it
exists when acquiring a new (next) lock.
This patch prints the shortest path from the next lock to be
acquired to the previous held lock if a circle is found.
The patch still uses the current method to check circle, and
once the circle is found, breadth-first search algorithem is
used to compute the shortest path from the next lock to the
previous lock in the forward lock dependency graph.
Printing the shortest path will shorten the dependency chain,
and make troubleshooting for possible circular locking easier.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1246201486-7308-2-git-send-email-tom.leiming@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The aligned ctx helper was using a bogus alignment value thas was
one off the correct value. Fortunately the current users do not
require anything beyond the natural alignment of the platform so
this hasn't caused a problem.
This patch fixes that and also removes the unnecessary minimum
check since if the alignment is less than the natural alignment
then the subsequent ALIGN operation should be a noop.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This provides a list of sockets with their Phonet bind addresses and
some socket debug informations through /proc/net/phonet.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are not supposed to be modified by drivers, so make them const.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Incorrect device area lengths are being passed to device_area_is_valid().
The regression appeared in 2.6.31-rc1 through commit
754c5fc7eb.
With the dm-stripe target, the size of the target (ti->len) was used
instead of the stripe_width (ti->len/#stripes). An example of a
consequent incorrect error message is:
device-mapper: table: 254:0: sdb too small for target
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
include/net/ieee802154/af_ieee802154.h (and others) naming seems to be too long
and redundant. Drop one level of subdirectories.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
