mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio's dev field needs to be set before mdio ops occur.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the QNAP TS-119 and TS-219 the wrong MPPs were used for the SATA
activity/presence LEDs. The new settings make these LEDs work as
expected.
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The use of unspecified protocol in IPv6 initial route prevents quagga to
install IPv6 default route:
# show ipv6 route
S ::/0 [1/0] via fe80::1, eth1_0
K>* ::/0 is directly connected, lo, rej
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
unreachable default dev lo proto none metric -1 error -101 hoplimit 255
The attached patch ensures RTPROT_KERNEL to the default initial route
and fixes the problem for quagga.
This is similar to "ipv6: protocol for address routes"
f410a1fba7.
# show ipv6 route
S>* ::/0 [1/0] via fe80::1, eth1_0
C>* ::1/128 is directly connected, lo
C>* fe80::/64 is directly connected, eth1_0
# ip -6 route
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
fe80::/64 dev eth1_0 proto kernel metric 256 mtu 1500 advmss 1440
hoplimit -1
ff00::/8 dev eth1_0 metric 256 mtu 1500 advmss 1440 hoplimit -1
default via fe80::1 dev eth1_0 proto zebra metric 1024 mtu 1500
advmss 1440 hoplimit -1
unreachable default dev lo proto kernel metric -1 error -101 hoplimit 255
Signed-off-by: Jean-Mickael Guerin <jean-mickael.guerin@6wind.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qeth_clear_output_buffer for HiperSockets may not clear
all 16 SBALEs, but only the used ones. The error flag in SBALF15
has to be cleared in any case.
Signed-off-by: Klaus-Dieter Wacker <kdwacker@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For HiperSocket devices receive-path checksumming is not required.
Thus NO_CHECKSUMMING is used as default for HiperSocket interfaces.
For layer3 devices configured with NO_CHECKSUMMING received skbs
should have set their ip_summed field to CHECKSUM_UNNECESSARY.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
z/VM Virtual Switch Port Isolation allows guests on a VLAN UNAWARE
virtual switch to be isolated from other guests on the VSWITCH.
(See z/VM Apars VM64281 and VM64463).
The Linux qeth driver is affected, because it has to handle new
error codes introduced with the z/VM VSWITCH Port Isolation support.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Channels are already removed when setting a ctcm-device offline.
Thus ctcm_remove_device must not refer to channel information.
Solution: delete channel information from the trace call in
ctcm_remove_device.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qeth device is plugged off, setting the device online stops in
state HARDSETUP and a failure is reported to the base cio-layer
causing halt/clear to be invoked. Replugging the device again triggers
a qeth recovery without notification of the cio-layer. If a device
is ungrouped in this state, the qeth set_offline function is not
invoked, because the corresponding ccwgroup device is not in state
ONLINE. Then incoming traffic is still handled by the qdio layer
resulting in a crash in qeth_l<x>_qdio_input_handler, because (part
of) the qeth data structures for this device are already removed.
Solution: After replugging the device qeth recovery should lead to a
working net device. Thus a "LAN offline" result when setting a qeth
device online must not report a failure to the base cio-layer.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink message header (struct nlmsghdr) is an unused parameter in
fill method of fib_rules_ops struct. This patch removes this
parameter from this method and fixes the places where this method is
called.
(include/net/fib_rules.h)
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander V. Lukyanov found a regression in 2.6.29 and made a complete
analysis found in http://bugzilla.kernel.org/show_bug.cgi?id=13339
Quoted here because its a perfect one :
begin_of_quotation
2.6.29 patch has introduced flexible route cache rebuilding. Unfortunately the
patch has at least one critical flaw, and another problem.
rt_intern_hash calculates rthi pointer, which is later used for new entry
insertion. The same loop calculates cand pointer which is used to clean the
list. If the pointers are the same, rtable leak occurs, as first the cand is
removed then the new entry is appended to it.
This leak leads to unregister_netdevice problem (usage count > 0).
Another problem of the patch is that it tries to insert the entries in certain
order, to facilitate counting of entries distinct by all but QoS parameters.
Unfortunately, referencing an existing rtable entry moves it to list beginning,
to speed up further lookups, so the carefully built order is destroyed.
For the first problem the simplest patch it to set rthi=0 when rthi==cand, but
it will also destroy the ordering.
end_of_quotation
Problematic commit is 1080d709fb
(net: implement emergency route cache rebulds when gc_elasticity is exceeded)
Trying to keep dst_entries ordered is too complex and breaks the fact that
order should depend on the frequency of use for garbage collection.
A possible fix is to make rt_intern_hash() simpler, and only makes
rt_check_expire() a litle bit smarter, being able to cope with an arbitrary
entries order. The added loop is running on cache hot data, while cpu
is prefetching next object, so should be unnoticied.
Reported-and-analyzed-by: Alexander V. Lukyanov <lav@yar.ru>
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_check_expire() computes average and standard deviation of chain lengths,
but not correclty reset length to 0 at beginning of each chain.
This probably gives overflows for sum2 (and sum) on loaded machines instead
of meaningful results.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-2.6:
drm: Copy back ioctl data to userspace regardless of return code.
drm: Round size of SHM maps to PAGE_SIZE
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: 64-bit: Fix system lockup.
MIPS: IP28: Change to build with -mr10k-cache-barrier=store
MIPS: IP22: Fix hang in power button interrupt handler
MIPS: IP32: Fix hang on shutdown in power button interrupt handler.
Stephen Rothwell <sfr@canb.auug.org.au> writes:
> Today's linux-next build of at least some av32 and arm configs failed like this:
>
> arch/avr32/kernel/signal.c:216: error: conflicting types for 'restart_syscall'
> include/linux/sched.h:2184: error: previous definition of 'restart_syscall' was here
>
> Caused by commit 690cc3ffe3 ("syscall:
> Implement a convinience function restart_syscall") from the net tree.
Grrr. Some days it feels like all of the good names are already taken.
Let's just rename the two static users in arm and avr32 to get this
sorted out.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The second argument of the probe method points to the amba_id
structure, so it's better passed with the correct type. None of the
current in-tree drivers uses the pointer, so they have only been
checked for a clean compile.
Change suggested by Russell King.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix function declarations:
drivers/scsi/fcoe/fcoe.c:1356:28: warning: non-ANSI function declaration of function 'fcoe_dev_setup'
drivers/scsi/libfc/fc_rport.c:1293:20: warning: non-ANSI function declaration of function 'fc_setup_rport'
drivers/scsi/libfc/fc_rport.c:1302:23: warning: non-ANSI function declaration of function 'fc_destroy_rport'
[jejb: fixed wrong doc in comment noticed during inspection]
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During device discovery read capacity fails with 0x020401 and sets the
device size to 0. As a reason any I/O submitted to this path gets
killed at sd_prep_fn with BLKPREP_KILL. This patch is to retry for
0x020401. NEED_RETRY in scsi_decide_disposition does not give
sufficient time for the device to become ready.
Signed-off-by: Vijay Chauhan <vijay.chauhan@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Make the sym53c8xx_2 driver slave_alloc/destroy less unsafe. References
to the destroyed LCB are cleared from the target structure (instead of
leaving a dangling pointer), and when the last LCB for the target is
destroyed the reference to the upper layer target data is cleared. The
host lock is used to prevent a race with the interrupt handler. Also
user commands are prevented for targets with all LCBs destroyed.
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
(Resent with proper formatting)
Fix for the sym53c8xx_2 driver to initialize lun's to_clear flag after
a bus reset (a failed clear can trigger a bus reset and it should not
be attemped again after that).
Signed-off-by: Aaro Koskinen <Aaro.Koskinen@nokia.com>
Tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver now waits for the scsi commands associated with a
particular error recovery step to be returned to the mid-layer,
and returns the appropriate SUCCESS or FAILED status. Removes
unneeded polling of chip for interrupts.
This patch also bumps the driver version number.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some unneeded, inactive and unused code, make some trivial
corrections to comments and a printk, and return a proper status
in qla1280_queuecommand. No fundamental logic changes are made.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch (as1224) changes the default timeout for INQUIRY commands
from 3 seconds to 20 seconds, which is the value used by Windows for
USB Mass-Storage devices. Some of these devices, like the Corsair
Flash Voyager (see Bugzilla #12188) really do need a long timeout.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This version contains following main changes
- Switch to new layout to support more types of ASIC.
- SSP TMF supported and related Error Handing enhanced.
- Support flash feature with delay 2*HZ when PHY changed.
- Support Marvell 94xx series ASIC for 6G SAS/SATA, which has 2
88SE64xx chips but any different register description.
- Support SPI flash for HBA-related configuration info.
- Other patch enhanced from kernel side such as increasing PHY type
[jejb: fold back in DMA_BIT_MASK changes]
Signed-off-by: Ying Chu <jasonchu@marvell.com>
Signed-off-by: Andy Yan <ayan@marvell.com>
Signed-off-by: Ke Wei <kewei@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Split mvsas driver into multiple source codes, based on the split
and function distribution found in Marvell's mvsas update.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Zero functional changes, just file movement.
This commit prepares for the upcoming integration of the
Marvell-provided driver update that splits the driver into support
for both 64xx and 94xx chip families.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Read adapter's physical port number from interrupt pin register
and use it instead of pci function number to offset into the
nvram to obtain the port's configuration parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Changing a lun's queue depth (/sys/block/sdX/device/queue_depth)
isn't sticky when the device is connected via a QLogic fibre
channel adapter.
The QLogic qla2xxx fibre channel driver dynamically adjusts a
lun's queue depth. If a user has a specific need to limit the
number of commands issued to a lun (say a tape drive, or a shared
raid where the total commands issued to all luns is limited at
the controller level, for example) and writes a limiting value to
/sys/block/sdXX/device/queue_depth, the qla2xxx driver will
silently and gradually increase the queue depth back to the
driver limit of ql2xmaxqdepth. While reducing this value (module
parameter) or increasing the interval between ramp ups
(ql2xqfullrampup) offers the potential for a work around it would
be better to have the option of just disabling the dynamic
adjustment of queue depth.
This patch implements an "off switch" as a module parameter.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the conditional plogi option bit whenever logging in the
fabric management server (if it is already logged in, it does not
need an explicit login; an implicit login suffices).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
srbs used to maintain a reference to the request queue on which
it was enqueued. This is no longer required as the request queue
pointer is now maintained in the scsi host that issues the srb.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the module parameter ql2xmultique_tag to 1 to enable this
feature. In this mode, the total number of response queues
created is equal to the number of online cpus. Turning the block
layer's rq_affinity mode on enables requests to be routed to the
proper cpu and at the same time it enables completion of the IO
in a response queue that is affined to the cpu in the request
path.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Set the number of request queues to the module paramater
ql2xmaxqueues. Each vport gets a request queue. The QoS value
set to the request queues determines priority control for queued
IOs. If QoS value is not specified, the vports use the default
queue 0.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The short-circuit to skip the non-applicable 'full-login-lip'
process on 81xx ISPs was nested too deeply in the 'bus-reset'
routine, as the code in qla2x00_loop_reset() should skip the
whole enable_lip_full_login process. The original code could
cause device tear-down due to the qla2x00_wait_for_loop_ready()
call taking a large amount of time.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Currently, we will ask the driver to configure right away
when somebody changes the desired BSSID. That's totally
strange because then we will configure the driver without
even knowing whether the BSS exists. Change this to only
configure the BSSID when associated, and configure a zero
BSSID when not associated.
As a side effect, this fixes an issue with the iwlwifi
driver which doesn't implement sta_notify properly and
uses the BSSID instead and gets very confused if the
BSSID is cleared before we disassociate, which results
in the warning Marcel posted [1] and iwlwifi bug 1995 [2].
[1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/32598
[2] http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1995
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
