emac_mdio_read_link() was not copying the requested phy settings
back into the emac driver's own phy api. This has caused a link
speed mismatch issue for the AR8035 as the emac driver kept
trying to connect with 10/100MBps on a 1GBit/s link.
This patch also unifies shared code between emac_setup_aneg()
and emac_mdio_setup_forced(). And furthermore it removes
a chunk of emac_mdio_init_phy(), that was copying the same
data into itself.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where the AR8035 PHY can't be
detected on an Cisco Meraki MR24, if the ethernet cable is
not connected on boot.
Russell Senior provided steps to reproduce the issue:
|Disconnect ethernet cable, apply power, wait until device has booted,
|plug in ethernet, check for interfaces, no eth0 is listed.
|
|This appears to be a problem during probing of the AR8035 Phy chip.
|When ethernet has no link, the phy detection fails, and eth0 is not
|created. Plugging ethernet later has no effect, because there is no
|interface as far as the kernel is concerned. The relevant part of
|the boot log looks like this:
|this is the failing case:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
|and the succeeding case:
|
|[ 0.876672] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.883952] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:01:..
|[ 0.890822] eth0: found Atheros 8035 Gigabit Ethernet PHY (0x01)
Based on the comment and the commit message of
commit 23fbb5a87c ("emac: Fix EMAC soft reset on 460EX/GT").
This is because the AR8035 PHY doesn't provide the TX Clock,
if the ethernet cable is not attached. This causes the reset
to timeout and the PHY detection code in emac_init_phy() is
unable to detect the AR8035 PHY. As a result, the emac driver
bails out early and the user left with no ethernet.
In order to stay compatible with existing configurations, the driver
tries the current reset approach at first. Only if the first attempt
timed out, it does perform one more retry with the clock temporarily
switched to the internal source for just the duration of the reset.
LEDE-Bug: #687 <https://bugs.lede-project.org/index.php?do=details&task_id=687>
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp22_port_mii_set() function was added by 2697582144, but the
function directly returns without doing anything. This return was used
when debugging and wasn't removed before sending the patch. Fix this.
Fixes: 2697582144 ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the mtu is currently not supported in the ibmvnic driver.
Implement .ndo_change_mtu in the driver so that attempting to use ifconfig
to change the mtu will fail and present the user with an error message.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When freeing VF's DMA mappings, an already NULLed pointer was checked
again due to an apparent copy&paste error. Consequently, the pf2vf
bulletin DMA mapping was not freed.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check that queue is less or equal to zero is always true
because queue is a u32; queue is decremented and will wrap around
and never go -ve. Fix this by making queue an int.
Detected by CoverityScan, CID#1428988 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tso_allocator can fail to set the Last Descriptor bit
on a descriptor that actually was the last descriptor.
This happens when the buffer of the last descriptor ends
up having a size of exactly TSO_MAX_BUFF_SIZE.
When the IP eventually reaches the next last descriptor,
which actually has the bit set, the DMA will hang.
When the DMA hangs, we get a tx timeout, however,
since stmmac does not do a complete reset of the IP
in stmmac_tx_timeout, we end up in a state with
completely hung TX.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethoc_reset enables device interrupts, ethoc_interrupt may schedule a
NAPI poll before NAPI is enabled in the ethoc_open, which results in
device being unable to send or receive anything until it's closed and
reopened. In case the device is flooded with ingress packets it may be
unable to recover at all.
Move napi_enable above ethoc_reset in the ethoc_open to fix that.
Fixes: a170285772 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.")
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current comparison of entry < 0 will never be true since entry is an
unsigned integer. Make entry an int to ensure -ve error return values
from the call to jumbo_frm are correctly being caught.
Detected by CoverityScan, CID#1238760 ("Macro compares unsigned to 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
i40e_build_skb updates the page_offset field with an incorrect offset,
which can lead to data corruption. This patch updates page_offset
correctly, by properly setting truesize.
Note that the bug only appears on architectures where PAGE_SIZE is
8192 or larger.
Fixes: f8b45b74cc ("i40e/i40evf: Use build_skb to build frames")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
introduced changes in the way i40e works with state flags converting
them to bitmaps using kernel bitmap API. This change introduced a
regression due to a mistaken substitution using __I40E_VSI_DOWN instead
of __I40E_DOWN when testing state of a PF at i40e_reset_subtask()
function. This caused a flood in the kernel log with the follow message:
[49.013] i40e 0002:01:00.0: bad reset request 0x00000020
Commit d19cb64b92 ("i40e: separate PF and VSI state flags")
also introduced some misuse of the VSI and PF flags, so both could be
considered as the offenders.
This patch simply fixes the flags where it makes sense by changing
__I40E_VSI_DOWN to __I40E_DOWN.
Fixes: 0da36b9774 ("i40e: use DECLARE_BITMAP for state fields")
Fixes: d19cb64b92 ("i40e: separate PF and VSI state flags")
Reviewed-by: "Guilherme G. Piccoli" <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: "Mauro S. M. Rodrigues" <maurosr@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Granular QoS per VF feature must be enabled in FW before it can be
used.
Thus, the driver cannot modify a QP's qos_vport value (via the UPDATE_QP FW
command) if the feature has not been enabled -- the FW returns an error if
this is attempted.
Fixes: 08068cd568 ("net/mlx4: Added qos_vport QP configuration in VST mode")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our previous patch (cited below) introduced a regression
for RAW Eth QPs.
Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.
Fixes: 89c557687a ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgbe_map_rx_buffer is rather confused about what PAGE_ALLOC_COSTLY_ORDER
means. It uses PAGE_ALLOC_COSTLY_ORDER-1 assuming that
PAGE_ALLOC_COSTLY_ORDER is the first costly order which is not the case
actually because orders larger than that are costly. And even that
applies only to sleeping allocations which is not the case here. We
simply do not perform any costly operations like reclaim or compaction
for those. Simplify the code by dropping the order calculation and use
PAGE_ALLOC_COSTLY_ORDER directly.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use software polling (PHY_POLL) to check for link state changes instead
of relying on the EMAC's hardware polling feature. Some PHY drivers
are unable to get a functioning link because the HW polling is not
robust enough.
The EMAC is able to poll the PHY on the MDIO bus looking for link state
changes (via the Link Status bit in the Status Register at address 0x1).
When the link state changes, the EMAC triggers an interrupt and tells the
driver what the new state is. The feature eliminates the need for
software to poll the MDIO bus.
Unfortunately, this feature is incompatible with phylib, because it
ignores everything that the PHY core and PHY drivers are trying to do.
In particular:
1. It assumes a compatible register set, so PHYs with different registers
may not work.
2. It doesn't allow for hardware errata that have work-arounds implemented
in the PHY driver.
3. It doesn't support multiple register pages. If the PHY core switches
the register set to another page, the EMAC won't know the page has
changed and will still attempt to read the same PHY register.
4. It only checks the copper side of the link, not the SGMII side. Some
PHY drivers (e.g. at803x) may also check the SGMII side, and
report the link as not ready during autonegotiation if the SGMII link
is still down. Phylib then waits for another interrupt to query
the PHY again, but the EMAC won't send another interrupt because it
thinks the link is up.
Cc: stable@vger.kernel.org # 4.11.x
Tested-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlogic's 82xx series adapter doesn't support
tunnel offloads, driver incorrectly assumes that it is
supported and causes firmware hang while running tunnel IO.
This patch fixes this by not advertising tunnel offloads
for 82xx adapters.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take uld mutex to avoid race between cxgb_up() and
cxgb4_register_uld() to enable napi for the same uld
queue.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SYSTEMPORT Lite, since we have the main interrupt source in the first
cell, the second cell is the Wake-on-LAN interrupt, yet the code was not
properly updated to fetch the second cell, and instead looked at the
third and non-existing cell for Wake-on-LAN.
Fixes: 44a4524c54 ("net: systemport: Add support for SYSTEMPORT Lite")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently multi-cos isn't working for bnx2x quite some time -
driver implements ndo_select_queue() to allow queue-selection
for FCoE, but the regular L2 flow would cause it to modulo the
fallback's result by the number of queues.
The fallback would return a queue matching the needed tc
[via __skb_tx_hash()], but since the modulo is by the number of TSS
queues where number of TCs is not accounted, transmission would always
be done by a queue configured into using TC0.
Fixes: ada7c19e6d ("bnx2x: use XPS if possible for bnx2x_select_queue instead of pure hash")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.45.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver may sleep under a write spin lock, and the function
call path is:
qlcnic_82xx_hw_write_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
qlcnic_82xx_hw_read_wx_2M (acquire the lock by write_lock_irqsave)
crb_win_lock
qlcnic_pcie_sem_lock
usleep_range
To fix it, the usleep_range is replaced with udelay.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NULL check before dereferencing pointer _id_ in order to avoid
a potential NULL pointer dereference.
Addresses-Coverity-ID: 1397995
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ax_init_dev (which is called only from the driver's .probe
function) calls free_irq in the error path without having requested the
irq in the first place. So drop the free_irq call in the error path.
Fixes: 825a2ff189 ("AX88796 network driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some of the be2net cards do not seem to be capabled
of performing checksum offload computions on Q-in-Q packets.
In these case, the recevied checksum on the remote is invalid
and TCP syn packets are dropped.
This patch adds a call to check disbled acceleration features
on Q-in-Q tagged traffic.
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-fixes-2017-05-23
Some TC offloads fixes from Or Gerlitz.
From Erez, mlx5 IPoIB RX fix to improve GRO.
From Mohamad, Command interface fix to improve mitigation against FW
commands timeouts.
From Tariq, Driver load Tolerance against affinity settings failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY require to wait for a bit after the reset GPIO has been
toggled. This adds support for the DT property `phy-reset-post-delay`
which gives the delay in milliseconds to wait after reset.
If the DT property is not given, no delay is observed. Post reset delay
greater than 1000ms are invalid.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tolerance to failures of irq_set_affinity_hint().
Its role is to give hints that optimizes performance,
and should not block the driver load.
In non-SMP systems, functionality is not available as
there is a single core, and all these calls definitely
fail. Hence, do not call the function and avoid the
warning prints.
Fixes: db058a186f ("net/mlx5_core: Set irq affinity hints")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf3 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
IPoIB packet contains the pseudo header area, we need to pull it prior
to reset_mac_header in order to let the GRO work well.
In more details:
GRO checks the mac address of the new coming packet, it does that by
comparing the hard_header_len size of the current packet to the previous
one in that session, the comparison is over hard_header_len size.
Now, the driver prepares that area in the skb by allocating area from the
reserved part and resetting the correct mac header to it.
Fixes: 9d6bd752c6 ("net/mlx5e: IPoIB, RX handler")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The sparse tool emits these correct complaints:
drivers/net/ethernet/mellanox/mlx5/core//en_tc.c:1005:25: warning: cast to restricted __be32
drivers/net/ethernet/mellanox/mlx5/core//en_tc.c:1007:25: warning: cast to restricted __be16
The value is provided from user-space in network order, but there's
no way for them to realize that, avoid the warnings by casting to the
appropriate type.
Fixes: d79b6df6b1 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently we don't support partial header re-writes through TC pedit
action offloading. However, the code that enforces that wasn't err-ing
on cases where the first and last bits of the mask are set but there is
some zero bit between them, such as in the below example, fix that!
tc filter add dev enp1s0 protocol ip parent ffff: prio 10 flower
ip_proto udp dst_port 2001 skip_sw
action pedit munge ip src set 1.0.0.1 retain 0xff0000ff
Fixes: d79b6df6b1 ('net/mlx5e: Add parsing of TC pedit actions to HW format')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When offloading header re-writes, the HW re-calculates the relevant L3/L4
checksums. Hence, when upper layers (as done by OVS) ask for TC checksum action
offload together with pedit offload, don't err. This command now works:
tc filter add dev ens1f0 protocol ip parent ffff: prio 20 flower skip_sw
ip_proto tcp dst_port 9001
action pedit ex munge tcp dport set 0x1234 pipe
action csum tcp
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We wrongly direcly invoke hlist_del_rcu() and not hash_del_rcu() which
does a slightly different call now and may change later, fix that.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If dma mask checks fail in atl2_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds proper error code return value and
make error code setup unified.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got an FDB notification for a port that doesn't exist we
execute an FDB entry delete to prevent it from re-appearing the next
time we poll for notifications.
If the operation failed we would trigger a NULL pointer dereference as
'mlxsw_sp_port' is NULL.
Fix it by reporting the error using the underlying bus device instead.
Fixes: 12f1501e75 ("mlxsw: spectrum: remove FDB entry in case we get unknown object notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EPROBE_DEFER is not an error, hence printing an error message like
sh-eth ee700000.ethernet: failed to initialise MDIO
may confuse the user.
To fix this, suppress the error message in case of probe deferral.
While at it, shorten the message, and add the actual error code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO initialization failure message is printed using the network
device, before it has been registered, leading to:
(null): failed to initialise MDIO
Use the platform device instead to fix this:
sh-eth ee700000.ethernet: failed to initialise MDIO
Fixes: daacf03f0b ("sh_eth: Register MDIO bus before registering the network device")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During rif counter freeing the counter index can be invalid. Add check
of validity before freeing the counter.
Fixes: e0c0afd8aa ("mlxsw: spectrum: Support for counters on router interfaces")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of disabled counters the entry index will be incorrect. Fix this
by moving the entry index set before the counter status check.
Fixes: 2ba5999f00 ("mlxsw: spectrum: Add Support for erif table entries access")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number to 1.16.43.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, all the host based DCBX settings from lldpad will fail if the
firmware DCBX agent is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, bnxt_dcb_init() is called too early before we
determine if the firmware DCBX agent is running or not. As a result,
we are not setting the DCB_CAP_DCBX_HOST and DCB_CAP_DCBX_LLD_MANAGED
flags properly to report to DCBNL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
