Aquantia AQR813 is the Octal Port variant of the AQR113. Add PHY ID for
it to provide support for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for handling the EEE advertisement 2 register.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading EEE link partner ability 2 register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add and use genphy_c45_read_eee_cap2(), complementing
genphy_c45_read_eee_cap1().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a prerequisite for adding EEE CAP2 register support, complement
PHY_EEE_CAP1_FEATURES with PHY_EEE_CAP2_FEATURES.
For now only 2500baseT and 5000baseT modes are supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Aquantia AQR113 PHY ID. Aquantia AQR113 is just a chip size variant of
the already supported AQR133C where the only difference is the PHY ID
and the hw chip size.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we are checking whether the PHY package mode matches the
individual PHY interface modes at PHY package probe time, but at that time
we only know the PHY package mode and not the individual PHY interface
modes as of_get_phy_mode() that populates it will only get called once the
netdev to which PHY-s are attached to is being probed and thus this check
will always fail and return -EINVAL.
So, lets move this check to .config_init_once as at that point individual
PHY interface modes should be populated.
Fixes: d1cb613efb ("net: phy: qcom: add support for QCA807x PHY Family")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240212115043.1725918-1-robimarko@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DP83826 offers the possibility to tune the voltage of logical
levels of the MLT-3 encoded TX data. This is useful when there
is a voltage drop in between the PHY and the connector and we
want to increase the voltage levels to compensate for that drop.
Prior to PHY configuration, the driver SW resets the PHY which has
the same effect as the HW reset pin according to the datasheet.
Hence, there's no need to force update the VOD_CFG registers to make
sure they hold their reset values. VOD_CFG registers need to be
updated only if the DT has been configured with values other than
the reset ones.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Catalin Popescu <catalin.popescu@leica-geosystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PMD Global Transmit Disable bit should be cleared for normal operation.
This should be HW default, however I found that on Asus RT-AX89X that uses
AQR113C PHY and firmware 5.4 this bit is set by default.
With this bit set the AQR cannot achieve a link with its link-partner and
it took me multiple hours of digging through the vendor GPL source to find
this out, so lets always clear this bit during .config_init() to avoid a
situation like this in the future.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240211181732.646311-1-robimarko@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
QCA8072/5 have up to 2 LEDs attached for PHY.
LEDs can be configured to be ON/hw blink or be set to HW control.
Hw blink mode is set to blink at 4Hz or 250ms.
PHY can support both copper (TP) or fiber (FIBRE) kind and supports
different HW control modes based on the port type.
HW control modes supported for netdev trigger for copper ports are:
- LINK_10
- LINK_100
- LINK_1000
- TX
- RX
- FULL_DUPLEX
- HALF_DUPLEX
HW control modes supported for netdev trigger for fiber ports are:
- LINK_100
- LINK_1000
- TX
- RX
- FULL_DUPLEX
- HALF_DUPLEX
LED support conflicts with GPIO controller feature and must be disabled
if gpio-controller is used for the PHY.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize some qca808x LED functions in preparation for qca807x LED
support.
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port. To limit code duplication introduce micro functions that takes reg
instead of LED index to tweak all the supported LED modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port.
In preparation for qca807x introduction, move all the common define to
shared header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s.
They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te,
100BASE-TX and 1000BASE-T PHY-s.
They feature 2 SerDes, one for PSGMII or QSGMII connection with
MAC, while second one is SGMII for connection to MAC or fiber.
Both models have a combo port that supports 1000BASE-X and
100BASE-FX fiber.
PHY package can be configured in 3 mode following this table:
First Serdes mode Second Serdes mode
Option 1 PSGMII for copper Disabled
ports 0-4
Option 2 PSGMII for copper 1000BASE-X / 100BASE-FX
ports 0-4
Option 3 QSGMII for copper SGMII for
ports 0-3 copper port 4
Each PHY inside of QCA807x series has 4 digitally controlled
output only pins that natively drive LED-s.
But some vendors used these to driver generic LED-s controlled
by userspace, so lets enable registering each PHY as GPIO
controller and add driver for it.
These are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x
boards.
Co-developed-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY driver might require additional regs call after
genphy_c37_read_status() is called.
Expand genphy_c37_read_status to provide a bool wheather the link has
changed or not to permit PHY driver to skip additional regs call if
nothing has changed.
Every user of genphy_c37_read_status() is updated with the new
additional bool.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move more function to shared library in preparation for introduction of
new PHY Family qca807x that will make use of both functions from at803x
and qca808x as it's a transition PHY with some implementation of at803x
and some from the new qca808x.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devm/of_phy_package_join helper to join PHYs in a PHY package. These
are variant of the manual phy_package_join with the difference that
these will use DT nodes to derive the base_addr instead of manually
passing an hardcoded value.
An additional value is added in phy_package_shared, "np" to reference
the PHY package node pointer in specific PHY driver probe_once and
config_init_once functions to make use of additional specific properties
defined in the PHY package node in DT.
The np value is filled only with of_phy_package_join if a valid PHY
package node is found. A valid PHY package node must have the node name
set to "ethernet-phy-package".
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for scanning PHY in PHY package nodes. PHY packages nodes
are just container for actual PHY on the MDIO bus.
Their PHY address defined in the PHY package node are absolute and
reflect the address on the MDIO bus.
mdio_bus.c and of_mdio.c is updated to now support and parse also
PHY package subnode by checking if the node name match
"ethernet-phy-package".
As PHY package reg is mandatory and each PHY in the PHY package must
have a reg, every invalid PHY Package node is ignored and will be
skipped by the autoscan fallback.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When scanning the MDIO bus for C22 devices, the driver returning
-ENODEV is not considered fatal, it just indicates the MDIO bus master
knows there is no device at that address, maybe because of hardware
limitation.
Make the C45 scan code act on -ENODEV the same way, to make C22 and
C45 more uniform.
It is expected all reads for a given address will return -ENODEV, so
within get_phy_c45_ids() only the first place a read occurs has been
changed.
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default lan8841's 1588 clock frequency is 125MHz. But when adjusting
the frequency, it is using the 1PPM format of the lan8814. Which is the
wrong format as lan8814 has a 1588 clock frequency of 250MHz. So then
for each 1PPM adjustment would adjust less than expected.
Therefore fix this by using the correct 1PPM format for lan8841.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca808x PHY provide support for the led_polarity_set OP to configure
and apply the active-low property but on PHY reset, the Active High bit
is not set resulting in the LED driven as active-low.
To fix this, check if active-low is not set in DT and enable Active High
polarity by default to restore correct funcionality of the LED.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switching to using phy_modify_mmd and a more short version of the
LED ON/OFF condition in later revision, it was made a logic error where
value ? QCA808X_LED_FORCE_ON : QCA808X_LED_FORCE_OFF is always true as
value is always OR with QCA808X_LED_FORCE_EN due to missing ()
resulting in the testing condition being QCA808X_LED_FORCE_EN | value.
Add the () to apply the correct condition and restore correct
functionality of the brightness ON/OFF.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Almost all the QCA8081 PHY driver OPs are specific and only some of them
use the generic at803x.
To make the at803x code slimmer, move all the specific qca808x regs and
functions to a dedicated PHY driver.
Probe function and priv struct is reworked to allocate and use only the
qca808x specific data. Unused data from at803x PHY driver are dropped
from at803x priv struct.
Also a new Kconfig is introduced QCA808X_PHY, to compile the newly
introduced PHY driver for QCA8081 PHY.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Deatch qca83xx PHY driver from at803x.
The QCA83xx PHYs implement specific function and doesn't use generic
at803x so it can be detached from the driver and moved to a dedicated
one.
Probe function and priv struct is reimplemented to allocate and use
only the qca83xx specific data. Unused data from at803x PHY driver
are dropped from at803x priv struct.
This is to make slimmer PHY drivers instead of including lots of bloat
that would never be used in specific SoC.
A new Kconfig flag QCA83XX_PHY is introduced to compile the new
introduced PHY driver.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change genphy_c45_ethtool_[get|set]_eee to use EEE linkmode bitmaps.
This is a prerequisite for adding support for EEE modes beyond bit 31.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting or getting PHC time, the higher bits of the second time (>32
bits) they were ignored. Meaning that setting some time in the future like
year 2150, it was failing to set this.
The issue can be reproduced like this:
# phc_ctl /dev/ptp1 set 10000000000
phc_ctl[12.290]: set clock time to 10000000000.000000000 or Sat Nov 20 17:46:40 2286
# phc_ctl /dev/ptp1 get
phc_ctl[15.309]: clock time is 1410065411.018055420 or Sun Sep 7 04:50:11 2014
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240126073042.1845153-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add LED support for QCA8081 PHY.
Documentation for this LEDs PHY is very scarce even with NDA access
to Documentation for OEMs. Only the blink pattern are documented and are
very confusing most of the time. No documentation is present about
forcing the LED on/off or to always blink.
Those settings were reversed by poking the regs and trying to find the
correct bits to trigger these modes. Some bits mode are not clear and
maybe the documentation option are not 100% correct. For the sake of LED
support the reversed option are enough to add support for current LED
APIs.
Supported HW control modes are:
- tx
- rx
- link_10
- link_100
- link_1000
- link_2500
- half_duplex
- full_duplex
Also add support for LED polarity set to set LED polarity to active
high or low. QSDK sets this value to high by default but PHY reset value
doesn't have this enabled by default.
QSDK also sets 2 additional bits but their usage is not clear, info about
this is added in the header. It was verified that for correct function
of the LED if active high is needed, only BIT 6 is needed.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for PHY LEDs polarity modes. Some PHY require LED to be set
to active low to be turned ON. Adds support for this by declaring
active-low property in DT.
PHY driver needs to declare .led_polarity_set() to configure LED
polarity modes. Function will pass the index with the LED index and a
bitmap with all the required modes to set.
Current supported modes are:
- active-low with the flag PHY_LED_ACTIVE_LOW. LED is set to active-low
to turn it ON.
- inactive-high-impedance with the flag PHY_LED_INACTIVE_HIGH_IMPEDANCE.
LED is set to high impedance to turn it OFF.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240125203702.4552-4-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The HW has the capability to check each frame if it is a PTP frame,
which domain it is, which ptp frame type it is, different ip address in
the frame. And if one of these checks fail then the frame is not
timestamp. Most of these checks were disabled except checking the field
minorVersionPTP inside the PTP header. Meaning that once a partner sends
a frame compliant to 8021AS which has minorVersionPTP set to 1, then the
frame was not timestamp because the HW expected by default a value of 0
in minorVersionPTP. This is exactly the same issue as on lan8841.
Fix this issue by removing this check so the userspace can decide on this.
Fixes: ece1950283 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The referenced commit moved the setting of the Autoneg and pause bits
early in sfp_parse_support(). However, we check whether the modes are
empty before using the bitrate to set some modes. Setting these bits
so early causes that test to always be false, preventing this working,
and thus some modules that used to work no longer do.
Move them just before the call to the quirk.
Fixes: 8110633db4 ("net: sfp-bus: allow SFP quirks to override Autoneg and pause bits")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://lore.kernel.org/r/E1rPMJW-001Ahf-L0@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b373 ("net: phy: micrel: add Microchip KSZ9131 initial driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
