This patch added a new member named csum_enabled in struct mptcp_sock,
used a dummy mptcp_is_checksum_enabled() helper to initialize it.
Also added a new member named mptcpi_csum_enabled in struct mptcp_info
to expose the csum_enabled flag.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IETF RFC 8986 [1] includes the definition of SRv6 End.DT4, End.DT6, and
End.DT46 Behaviors.
The current SRv6 code in the Linux kernel only implements End.DT4 and
End.DT6 which can be used respectively to support IPv4-in-IPv6 and
IPv6-in-IPv6 VPNs. With End.DT4 and End.DT6 it is not possible to create a
single SRv6 VPN tunnel to carry both IPv4 and IPv6 traffic.
The proposed End.DT46 implementation is meant to support the decapsulation
of IPv4 and IPv6 traffic coming from a single SRv6 tunnel.
The implementation of the SRv6 End.DT46 Behavior in the Linux kernel
greatly simplifies the setup and operations of SRv6 VPNs.
The SRv6 End.DT46 Behavior leverages the infrastructure of SRv6 End.DT{4,6}
Behaviors implemented so far, because it makes use of a VRF device in
order to force the routing lookup into the associated routing table.
To make the End.DT46 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one VRF
during the tunnel creation. Such constraint has to be enforced by enabling
the VRF strict_mode sysctl parameter, i.e.:
$ sysctl -wq net.vrf.strict_mode=1
Note that the same approach is used for the SRv6 End.DT4 Behavior and for
the End.DT6 Behavior in VRF mode.
The command used to instantiate an SRv6 End.DT46 Behavior is
straightforward, i.e.:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT46 vrftable 100 dev vrf100.
[1] https://www.rfc-editor.org/rfc/rfc8986.html#name-enddt46-decapsulation-and-s
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Performance and impact of SRv6 End.DT46 Behavior on the SRv6 Networking
=======================================================================
This patch aims to add the SRv6 End.DT46 Behavior with minimal impact on
the performance of SRv6 End.DT4 and End.DT6 Behaviors.
In order to verify this, we tested the performance of the newly introduced
SRv6 End.DT46 Behavior and compared it with the performance of SRv6
End.DT{4,6} Behaviors, considering both the patched kernel and the kernel
before applying the End.DT46 patch (referred to as vanilla kernel).
In details, the following decapsulation scenarios were considered:
1.a) IPv6 traffic in SRv6 End.DT46 Behavior on patched kernel;
1.b) IPv4 traffic in SRv6 End.DT46 Behavior on patched kernel;
2.a) SRv6 End.DT6 Behavior (VRF mode) on patched kernel;
2.b) SRv6 End.DT4 Behavior on patched kernel;
3.a) SRv6 End.DT6 Behavior (VRF mode) on vanilla kernel (without the
End.DT46 patch);
3.b) SRv6 End.DT4 Behavior on vanilla kernel (without the End.DT46 patch).
All tests were performed on a testbed deployed on the CloudLab [2]
facilities. We considered IPv{4,6} traffic handled by a single core (at 2.4
GHz on a Xeon(R) CPU E5-2630 v3) on kernel 5.13-rc1 using packets of size
~ 100 bytes.
Scenario (1.a): average 684.70 kpps; std. dev. 0.7 kpps;
Scenario (1.b): average 711.69 kpps; std. dev. 1.2 kpps;
Scenario (2.a): average 690.70 kpps; std. dev. 1.2 kpps;
Scenario (2.b): average 722.22 kpps; std. dev. 1.7 kpps;
Scenario (3.a): average 690.02 kpps; std. dev. 2.6 kpps;
Scenario (3.b): average 721.91 kpps; std. dev. 1.2 kpps;
Considering the results for the patched kernel (1.a, 1.b, 2.a, 2.b) we
observe that the performance degradation incurred in using End.DT46 rather
than End.DT6 and End.DT4 respectively for IPv6 and IPv4 traffic is minimal,
around 0.9% and 1.5%. Such very minimal performance degradation is the
price to be paid if one prefers to use a single tunnel capable of handling
both types of traffic (IPv4 and IPv6).
Comparing the results for End.DT4 and End.DT6 under the patched and the
vanilla kernel (2.a, 2.b, 3.a, 3.b) we observe that the introduction of the
End.DT46 patch has no impact on the performance of End.DT4 and End.DT6.
[2] https://www.cloudlab.us
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-17
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 25 day(s) which contain
a total of 148 files changed, 4779 insertions(+), 1248 deletions(-).
The main changes are:
1) BPF infrastructure to migrate TCP child sockets from a listener to another
in the same reuseport group/map, from Kuniyuki Iwashima.
2) Add a provably sound, faster and more precise algorithm for tnum_mul() as
noted in https://arxiv.org/abs/2105.05398, from Harishankar Vishwanathan.
3) Streamline error reporting changes in libbpf as planned out in the
'libbpf: the road to v1.0' effort, from Andrii Nakryiko.
4) Add broadcast support to xdp_redirect_map(), from Hangbin Liu.
5) Extends bpf_map_lookup_and_delete_elem() functionality to 4 more map
types, that is, {LRU_,PERCPU_,LRU_PERCPU_,}HASH, from Denis Salopek.
6) Support new LLVM relocations in libbpf to make them more linker friendly,
also add a doc to describe the BPF backend relocations, from Yonghong Song.
7) Silence long standing KUBSAN complaints on register-based shifts in
interpreter, from Daniel Borkmann and Eric Biggers.
8) Add dummy PT_REGS macros in libbpf to fail BPF program compilation when
target arch cannot be determined, from Lorenz Bauer.
9) Extend AF_XDP to support large umems with 1M+ pages, from Magnus Karlsson.
10) Fix two minor libbpf tc BPF API issues, from Kumar Kartikeya Dwivedi.
11) Move libbpf BPF_SEQ_PRINTF/BPF_SNPRINTF macros that can be used by BPF
programs to bpf_helpers.h header, from Florent Revest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Th_strings arrays netdev_features_strings, tunable_strings, and
phy_tunable_strings has been moved to file net/ethtool/common.c.
So fixes the comment.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to collect more detailed SMC fallback reason statistics and
provide these statistics to user space on the netlink interface.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the netlink function which collects the statistics information and
delivers it to the userspace.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new bpf_attach_type for BPF_PROG_TYPE_SK_REUSEPORT
to check if the attached eBPF program is capable of migrating sockets. When
the eBPF program is attached, we run it for socket migration if the
expected_attach_type is BPF_SK_REUSEPORT_SELECT_OR_MIGRATE or
net.ipv4.tcp_migrate_req is enabled.
Currently, the expected_attach_type is not enforced for the
BPF_PROG_TYPE_SK_REUSEPORT type of program. Thus, this commit follows the
earlier idea in the commit aac3fc320d ("bpf: Post-hooks for sys_bind") to
fix up the zero expected_attach_type in bpf_prog_load_fixup_attach_type().
Moreover, this patch adds a new field (migrating_sk) to sk_reuseport_md to
select a new listener based on the child socket. migrating_sk varies
depending on if it is migrating a request in the accept queue or during
3WHS.
- accept_queue : sock (ESTABLISHED/SYN_RECV)
- 3WHS : request_sock (NEW_SYN_RECV)
In the eBPF program, we can select a new listener by
BPF_FUNC_sk_select_reuseport(). Also, we can cancel migration by returning
SK_DROP. This feature is useful when listeners have different settings at
the socket API level or when we want to free resources as soon as possible.
- SK_PASS with selected_sk, select it as a new listener
- SK_PASS with selected_sk NULL, fallbacks to the random selection
- SK_DROP, cancel the migration.
There is a noteworthy point. We select a listening socket in three places,
but we do not have struct skb at closing a listener or retransmitting a
SYN+ACK. On the other hand, some helper functions do not expect skb is NULL
(e.g. skb_header_pointer() in BPF_FUNC_skb_load_bytes(), skb_tail_pointer()
in BPF_FUNC_skb_load_bytes_relative()). So we allocate an empty skb
temporarily before running the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201123003828.xjpjdtk4ygl6tg6h@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201203042402.6cskdlit5f3mw4ru@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201209030903.hhow5r53l6fmozjn@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-10-kuniyu@amazon.co.jp
We will call sock_reuseport.prog for socket migration in the next commit,
so the eBPF program has to know which listener is closing to select a new
listener.
We can currently get a unique ID of each listener in the userspace by
calling bpf_map_lookup_elem() for BPF_MAP_TYPE_REUSEPORT_SOCKARRAY map.
This patch makes the pointer of sk available in sk_reuseport_md so that we
can get the ID by BPF_FUNC_get_socket_cookie() in the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201119001154.kapwihc2plp4f7zc@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-9-kuniyu@amazon.co.jp
Add support to create (and destroy) interfaces via a new
rtnetlink kind "wwan". The responsible driver has to use
the new wwan_register_ops() to make this possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, for example in the upcoming WWAN framework changes,
there's no natural "parent netdev", so sometimes dummy netdevs are
created or similar. IFLA_PARENT_DEV_NAME is a new attribute intended to
contain a device (sysfs, struct device) name that can be used instead
when creating a new netdev, if the rtnetlink family implements it.
As suggested by Parav Pandit, we also introduce IFLA_PARENT_DEV_BUS_NAME
attribute in order to uniquely identify a device on the system (with
bus/name pair).
ip-link(8) support for the generic parent device attributes will help
us avoid code duplication, so no other link type will require a custom
code to handle the parent name attribute. E.g. the WWAN interface
creation command will looks like this:
$ ip link add wwan0-1 parent-dev wwan0 type wwan channel-id 1
So, some future subsystem (or driver) FOO will have an interface
creation command that looks like this:
$ ip link add foo1-3 parent-dev foo1 type foo bar-id 3 baz-type Y
Below is an example of dumping link info of a random device with these
new attributes:
$ ip --details link show wlp0s20f3
4: wlp0s20f3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP mode DORMANT group default qlen 1000
...
parent_bus pci parent_dev 0000:00:14.3
Co-developed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Co-developed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add set of defines and constants for SOCK_SEQPACKET support
in vsock.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLMSG_LENGTH(0) may confuse the API users,
NLMSG_HDRLEN is much more clear.
Besides, some code style problems are also fixed.
Signed-off-by: Chen Li <chenli@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Add nfgenmsg field to nfnetlink's struct nfnl_info and use it.
2) Remove nft_ctx_init_from_elemattr() and nft_ctx_init_from_setattr()
helper functions.
3) Add the nf_ct_pernet() helper function to fetch the conntrack
pernetns data area.
4) Expose TCP and UDP flowtable offload timeouts through sysctl,
from Oz Shlomo.
5) Add nfnetlink_hook subsystem to fetch the netfilter hook
pipeline configuration, from Florian Westphal. This also includes
a new field to annotate the hook type as metadata.
6) Fix unsafe memory access to non-linear skbuff in the new SCTP
chunk support for nft_exthdr, from Phil Sutter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This nfnl subsystem allows to dump the list of all active netfiler hooks,
e.g. defrag, conntrack, nf/ip/arp/ip6tables and so on.
This helps to see what kind of features are currently enabled in
the network stack.
Sample output from nft tool using this infra:
$ nft list hook ip input
family ip hook input {
+0000000010 nft_do_chain_inet [nf_tables] # nft table firewalld INPUT
+0000000100 nf_nat_ipv4_local_in [nf_nat]
+2147483647 ipv4_confirm [nf_conntrack]
}
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
- Fixes UAF and CVE-2021-3564
- Fix VIRTIO_ID_BT to use an unassigned ID
- Fix firmware loading on some Intel Controllers
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEE7E6oRXp8w05ovYr/9JCA4xAyCykFAmC5RWQZHGx1aXoudm9u
LmRlbnR6QGludGVsLmNvbQAKCRD0kIDjEDILKS0+D/4kJF7G9FohvLJUzTrrhcPx
nEE/5IL1eZeCQVCdKmgMeiy6K2iARGY9ZNqnx/AX1SJN9bHI7WsL6uy2RV7r57kx
iP2XZsV2uzXbwY9KVvfXBMNoCA2E4xS0UxpxA2h1znRUgMWDFLFkZydwYsBieGb6
tXZwJo3WOnDp169RbKdWTrWstYlL6KTTJoIxaVYWlghXVZ8Fl8LUHbhnx5MEqhqz
469AfGDlUKEoiYUUDwNrwX1ory/RWhcDxTFpDeji48U0P7oLFL73Aoyy/WP0B2FO
dhOErn38YUDivwBqSO2O21RUsICREbyLqHy6K/JWe4RqY50nEmWhfQo59ApzSuV3
e2HcbDwK5vgGYxmU6T9vb5S0nV1AgTV+5O3t1Mj6ZVqTAl6b2OkfqskCZzTrklIS
aKIP4viRAPLsJMdKKHW1mhR3zBH0deYEovIpFy+LkjX5aFsrEgc8hRn7i5ceF8GW
d+Ov9LPJQJQTK+r6W7xPiCUkC1dj/SMZ756Gr6cGhXPzY1DgBoyaaoZV1K4mz17g
dlLwXfF4nIJqJFop3iTPVGWVoeapZ/tgu73iTUdkXIEbqj19wj67nw+xz0WGs1pB
B1H/OemQS4/yfo4IsfLRDAJ14Q+5JS4qRKBf7p4e/yj533BW6lia0GTdujO+N4eT
FQfnUoYaexkiPYwGMyjRpQ==
=X9Cg
-----END PGP SIGNATURE-----
Merge tag 'for-net-2021-06-03' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
bluetooth pull request for net:
- Fixes UAF and CVE-2021-3564
- Fix VIRTIO_ID_BT to use an unassigned ID
- Fix firmware loading on some Intel Controllers
Signed-off-by: David S. Miller <davem@davemloft.net>
Including <linux/in.h> and <netinet/in.h> in the dependencies breaks
compilation of trinity due to multiple definitions. <linux/in.h> is only
used in <linux/icmp.h> to provide the definition of the struct in_addr,
but this can be substituted out by using the datatype __be32.
Signed-off-by: Andreas Roeseler <andreas.a.roeseler@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It turned out that the VIRTIO_ID_* are not assigned in the virtio_ids.h
file in the upstream kernel. Picking the next free one was wrong and
there is a process that has been followed now.
See https://github.com/oasis-tcs/virtio-spec/issues/108 for details.
Fixes: afd2daa26c ("Bluetooth: Add support for virtio transport driver")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Refactor DEVLINK_CMD_RATE_{GET|SET} command handlers to support setting
a node as a parent for another rate object (leaf or node) by means of
new attribute DEVLINK_ATTR_RATE_PARENT_NODE_NAME. Extend devlink ops
with new callbacks rate_{leaf|node}_parent_set() to set node as a parent
for rate object to allow supporting drivers to implement rate grouping
through devlink. Driver implementations are allowed to support leafs
or node children only. Invoking callback with NULL as parent should be
threated by the driver as unset parent action.
Extend rate object struct with reference counter to disallow deleting a
node with any child pointing to it. User should unset parent for the
child explicitly.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate add netdevsim/netdevsim10/group2
$ devlink port function rate set netdevsim/netdevsim10/group1 parent group2
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node parent group2
$ devlink port function rate set netdevsim/netdevsim10/group1 noparent
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_{NEW|DEL} commands that are used
to create and delete devlink rate nodes. Add new attribute
DEVLINK_ATTR_RATE_NODE_NAME that specify node name string. The node name
is an alphanumeric identifier. No valid node name can be a devlink port
index, eg. decimal number. Extend devlink ops with new callbacks
rate_node_{new|del}() and rate_node_tx_{share|max}_set() to allow
supporting drivers to implement ports rate grouping and setting tx rate
of rate nodes through devlink.
Expose devlink_rate_nodes_destroy() function to allow vendor driver do
proper cleanup of internally allocated resources for the nodes if the
driver goes down or due to any other reasons which requires nodes to be
destroyed.
Disallow moving device from switchdev to legacy mode if any node exists
on that device. User must explicitly delete nodes before switching mode.
Example:
$ devlink port function rate add netdevsim/netdevsim10/group1
$ devlink port function rate set netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
Add + set command can be combined:
$ devlink port function rate add netdevsim/netdevsim10/group1 \
tx_share 10mbit tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/group1
netdevsim/netdevsim10/group1: type node tx_share 10mbit tx_max 100mbit
$ devlink port function rate del netdevsim/netdevsim10/group1
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement support for DEVLINK_CMD_RATE_SET command with new attributes
DEVLINK_ATTR_RATE_TX_{SHARE|MAX} that are used to set devlink rate
shared/max tx rate values. Extend devlink ops with new callbacks
rate_leaf_tx_{share|max}_set() to allow supporting drivers to implement
rate control through devlink.
New attributes are optional. Driver implementations are allowed to
support either or both of them.
Shared rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_share 10mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_share 10mbit
Max rate example:
$ devlink port function rate set netdevsim/netdevsim10/0 tx_max 100mbit
$ devlink port function rate show netdevsim/netdevsim10/0
netdevsim/netdevsim10/0: type leaf tx_max 100mbit
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow registering rate object for devlink ports with dedicated
devlink_rate_leaf_{create|destroy}() API. Implement new netlink
DEVLINK_CMD_RATE_GET command that is used to retrieve rate object info.
Add new DEVLINK_CMD_RATE_{NEW|DEL} commands that are used for
notifications when creating/deleting leaf rate object.
Rate API is intended to be used for rate limiting of individual
devlink ports (leafs) and their aggregates (nodes).
Example:
$ devlink port show
pci/0000:03:00.0/0
pci/0000:03:00.0/1
$ devlink port function rate show
pci/0000:03:00.0/0: type leaf
pci/0000:03:00.0/1: type leaf
Co-developed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Support for SCTP chunks matching on nf_tables, from Phil Sutter.
2) Skip LDMXCSR, we don't need a valid MXCSR state. From Stefano Brivio.
3) CONFIG_RETPOLINE for nf_tables set lookups, from Florian Westphal.
4) A few Kconfig leading spaces removal, from Juerg Haefliger.
5) Remove spinlock from xt_limit, from Jason Baron.
6) Remove useless initialization in xt_CT, oneliner from Yang Li.
7) Tree-wide replacement of netlink_unicast() by nfnetlink_unicast().
8) Reduce footprint of several structures: xt_action_param,
nft_pktinfo and nf_hook_state, from Florian.
10) Add nft_thoff() and nft_sk() helpers and use them, also from Florian.
11) Fix documentation in nf_tables pipapo avx2, from Florian Westphal.
12) Fix clang-12 fmt string warnings, also from Florian.
====================
Adding support for MAPv5 egress packets.
This involves adding the MAPv5 header and setting the csum_valid_required
in the checksum header to request HW compute the checksum.
Corresponding stats are incremented based on whether the checksum is
computed in software or HW.
New stat has been added which represents the count of packets whose
checksum is calculated by the HW.
Signed-off-by: Sharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for processing of MAPv5 downlink packets.
It involves parsing the Mapv5 packet and checking the csum header
to know whether the hardware has validated the checksum and is
valid or not.
Based on the checksum valid bit the corresponding stats are
incremented and skb->ip_summed is marked either CHECKSUM_UNNECESSARY
or left as CHEKSUM_NONE to let network stack revalidate the checksum
and update the respective snmp stats.
Current MAPV1 header has been modified, the reserved field in the
Mapv1 header is now used for next header indication.
Signed-off-by: Sharath Chandra Vurukala <sharathv@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chunks are SCTP header extensions similar in implementation to IPv6
extension headers or TCP options. Reusing exthdr expression to find and
extract field values from them is therefore pretty straightforward.
For now, this supports extracting data from chunks at a fixed offset
(and length) only - chunks themselves are an extensible data structure;
in order to make all fields available, a nested extension search is
needed.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEK3kIWJt9yTYMP3ehqclaivrt76kFAmCvTYUTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCpyVqK+u3vqTxPB/4xVeasYKcyinylU7adBp9HFIvKjOiK
TpxQ7h4EhjJxkmQyONP529ZeQ5sjbnbc9IGkDQNhhVVm764LnEJ01aIi+kMtRs+M
szAGbWcITSyv4iaYCcKtNDSi2m74TK4gtRhsKItkIBRAZCs5jb54DSjWae7cGH0A
M/ts6WbYTbp89Lmww3mYtQ4dpmqvk/gXNbzKicrs2uGbPg0YTyq8rAQztt4yFaQR
9cBzxnwcfgvTz/uihkItiClv7kZIYjwzFB8BO1S2qx0TaUE1n78uiuuzcIdfvPt8
TKap7pwnjLYYToHokcWaU2t8Nd1Hy3KCaHuYO54TdXM4KYODJmbPydER
=pVNd
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.14-20210527' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
can-next 2021-05-27
The first 2 patches are by Geert Uytterhoeven and convert the rcan_can
and rcan_canfd device tree bindings to yaml.
The next 2 patches are by Oliver Hartkopp and me and update the CAN
uapi headers.
zuoqilin's patch removes an unnecessary variable from the CAN proc
code.
Patrick Menschel contributes 3 patches for CAN ISOTP to enhance the
error messages.
Jiapeng Chong's patch removes two dead stores from the softing driver.
The next 4 patches are by me and silence several warnings found by
clang compiler.
Jimmy Assarsson's patches for the kvaser_usb driver add support for
the Kvaser hydra devices.
Dario Binacchi provides 2 patches for the c_can driver, first removing
an unused variable, then adding basic ethtool support to query driver
and ring parameter info.
The last 4 patches are by Torin Cooper-Bennun and clean up the m_can
driver.
* tag 'linux-can-next-for-5.14-20210527' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (21 commits)
can: m_can: fix whitespace in a few comments
can: m_can: make TXESC, RXESC config more explicit
can: m_can: clean up CCCR reg defs, order by revs
can: m_can: use bits.h macros for all regmasks
can: c_can: add ethtool support
can: c_can: remove unused variable struct c_can_priv::rxmasked
can: kvaser_usb: Add new Kvaser hydra devices
can: kvaser_usb: Rename define USB_HYBRID_{,PRO_}CANLIN_PRODUCT_ID
can: at91_can: silence clang warning
can: mcp251xfd: silence clang warning
can: mcp251x: mcp251x_can_probe(): silence clang warning
can: hi311x: hi3110_can_probe(): silence clang warning
can: softing: Remove redundant variable ptr
can: isotp: Add error message if txqueuelen is too small
can: isotp: add symbolic error message to isotp_module_init()
can: isotp: change error format from decimal to symbolic error names
can: proc: remove unnecessary variables
can: uapi: introduce CANFD_FDF flag for mixed content in struct canfd_frame
can: uapi: update CAN-FD frame description
dt-bindings: can: rcar_canfd: Convert to json-schema
...
====================
Link: https://lore.kernel.org/r/20210527084532.1384031-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The struct can_frame and struct canfd_frame intentionally share the
same layout to be able to write CAN frame content into a CAN FD frame
structure. When this is done the former differentiation via CAN_MTU /
CANFD_MTU is lost. CANFD_FDF allows programmers to mark CAN FD frames
in the case of using struct canfd_frame for mixed CAN/CAN FD
content (dual use).
N.B. the Kernel APIs do NOT provide mixed CAN / CAN FD content inside
of struct canfd_frame therefore the CANFD_FDF flag is disregarded by
Linux.
Link: https://lore.kernel.org/r/20170411134343.3089-1-socketcan@hartkopp.net
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since an early version of the CAN-FD specification the bit that
defines a CAN-FD frame on the wire, has been renamed from Extended
Data Length (EDL) to FD Frame (FDF).
To avoid confusion, update the struct canfd_frame description in the
UAPI headers accordingly.
Link: https://lore.kernel.org/r/20210517113727.77597-1-mkl@pengutronix.de
Suggested-by: Ayoub Kaanich <kayoub5@live.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds two flags BPF_F_BROADCAST and BPF_F_EXCLUDE_INGRESS to
extend xdp_redirect_map for broadcast support.
With BPF_F_BROADCAST the packet will be broadcasted to all the interfaces
in the map. with BPF_F_EXCLUDE_INGRESS the ingress interface will be
excluded when do broadcasting.
When getting the devices in dev hash map via dev_map_hash_get_next_key(),
there is a possibility that we fall back to the first key when a device
was removed. This will duplicate packets on some interfaces. So just walk
the whole buckets to avoid this issue. For dev array map, we also walk the
whole map to find valid interfaces.
Function bpf_clear_redirect_map() was removed in
commit ee75aef23a ("bpf, xdp: Restructure redirect actions").
Add it back as we need to use ri->map again.
With test topology:
+-------------------+ +-------------------+
| Host A (i40e 10G) | ---------- | eno1(i40e 10G) |
+-------------------+ | |
| Host B |
+-------------------+ | |
| Host C (i40e 10G) | ---------- | eno2(i40e 10G) |
+-------------------+ | |
| +------+ |
| veth0 -- | Peer | |
| veth1 -- | | |
| veth2 -- | NS | |
| +------+ |
+-------------------+
On Host A:
# pktgen/pktgen_sample03_burst_single_flow.sh -i eno1 -d $dst_ip -m $dst_mac -s 64
On Host B(Intel(R) Xeon(R) CPU E5-2690 v3 @ 2.60GHz, 128G Memory):
Use xdp_redirect_map and xdp_redirect_map_multi in samples/bpf for testing.
All the veth peers in the NS have a XDP_DROP program loaded. The
forward_map max_entries in xdp_redirect_map_multi is modify to 4.
Testing the performance impact on the regular xdp_redirect path with and
without patch (to check impact of additional check for broadcast mode):
5.12 rc4 | redirect_map i40e->i40e | 2.0M | 9.7M
5.12 rc4 | redirect_map i40e->veth | 1.7M | 11.8M
5.12 rc4 + patch | redirect_map i40e->i40e | 2.0M | 9.6M
5.12 rc4 + patch | redirect_map i40e->veth | 1.7M | 11.7M
Testing the performance when cloning packets with the redirect_map_multi
test, using a redirect map size of 4, filled with 1-3 devices:
5.12 rc4 + patch | redirect_map multi i40e->veth (x1) | 1.7M | 11.4M
5.12 rc4 + patch | redirect_map multi i40e->veth (x2) | 1.1M | 4.3M
5.12 rc4 + patch | redirect_map multi i40e->veth (x3) | 0.8M | 2.6M
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/20210519090747.1655268-3-liuhangbin@gmail.com
Extend the existing bpf_map_lookup_and_delete_elem() functionality to
hashtab map types, in addition to stacks and queues.
Create a new hashtab bpf_map_ops function that does lookup and deletion
of the element under the same bucket lock and add the created map_ops to
bpf.h.
Signed-off-by: Denis Salopek <denis.salopek@sartura.hr>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/4d18480a3e990ffbf14751ddef0325eed3be2966.1620763117.git.denis.salopek@sartura.hr
Pull siginfo fix from Eric Biederman:
"During the merge window an issue with si_perf and the siginfo ABI came
up. The alpha and sparc siginfo structure layout had changed with the
addition of SIGTRAP TRAP_PERF and the new field si_perf.
The reason only alpha and sparc were affected is that they are the
only architectures that use si_trapno.
Looking deeper it was discovered that si_trapno is used for only a few
select signals on alpha and sparc, and that none of the other
_sigfault fields past si_addr are used at all. Which means technically
no regression on alpha and sparc.
While the alignment concerns might be dismissed the abuse of si_errno
by SIGTRAP TRAP_PERF does have the potential to cause regressions in
existing userspace.
While we still have time before userspace starts using and depending
on the new definition siginfo for SIGTRAP TRAP_PERF this set of
changes cleans up siginfo_t.
- The si_trapno field is demoted from magic alpha and sparc status
and made an ordinary union member of the _sigfault member of
siginfo_t. Without moving it of course.
- si_perf is replaced with si_perf_data and si_perf_type ending the
abuse of si_errno.
- Unnecessary additions to signalfd_siginfo are removed"
* 'for-v5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
signalfd: Remove SIL_PERF_EVENT fields from signalfd_siginfo
signal: Deliver all of the siginfo perf data in _perf
signal: Factor force_sig_perf out of perf_sigtrap
signal: Implement SIL_FAULT_TRAPNO
siginfo: Move si_trapno inside the union inside _si_fault
Here is a big set of char/misc/other driver fixes for 5.13-rc3.
The majority here is the fallout of the umn.edu re-review of all prior
submissions. That resulted in a bunch of reverts along with the
"correct" changes made, such that there is no regression of any of the
potential fixes that were made by those individuals. I would like to
thank the over 80 different developers who helped with the review and
fixes for this mess.
Other than that, there's a few habanna driver fixes for reported issues,
and some dyndbg fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYKZCBg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynhRQCdGk6ri4oluyn/Z/2KAjvXDOmTmvgAn12VP42d
S1Zmh4qRH2OWaLOBg7c2
=qtxj
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here is a big set of char/misc/other driver fixes for 5.13-rc3.
The majority here is the fallout of the umn.edu re-review of all prior
submissions. That resulted in a bunch of reverts along with the
"correct" changes made, such that there is no regression of any of the
potential fixes that were made by those individuals. I would like to
thank the over 80 different developers who helped with the review and
fixes for this mess.
Other than that, there's a few habanna driver fixes for reported
issues, and some dyndbg fixes for reported problems.
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (82 commits)
misc: eeprom: at24: check suspend status before disable regulator
uio_hv_generic: Fix another memory leak in error handling paths
uio_hv_generic: Fix a memory leak in error handling paths
uio/uio_pci_generic: fix return value changed in refactoring
Revert "Revert "ALSA: usx2y: Fix potential NULL pointer dereference""
dyndbg: drop uninformative vpr_info
dyndbg: avoid calling dyndbg_emit_prefix when it has no work
binder: Return EFAULT if we fail BINDER_ENABLE_ONEWAY_SPAM_DETECTION
cdrom: gdrom: initialize global variable at init time
brcmfmac: properly check for bus register errors
Revert "brcmfmac: add a check for the status of usb_register"
video: imsttfb: check for ioremap() failures
Revert "video: imsttfb: fix potential NULL pointer dereferences"
net: liquidio: Add missing null pointer checks
Revert "net: liquidio: fix a NULL pointer dereference"
media: gspca: properly check for errors in po1030_probe()
Revert "media: gspca: Check the return value of write_bridge for timeout"
media: gspca: mt9m111: Check write_bridge for timeout
Revert "media: gspca: mt9m111: Check write_bridge for timeout"
media: dvb: Add check on sp8870_readreg return
...
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-05-19
The following pull-request contains BPF updates for your *net-next* tree.
We've added 43 non-merge commits during the last 11 day(s) which contain
a total of 74 files changed, 3717 insertions(+), 578 deletions(-).
The main changes are:
1) syscall program type, fd array, and light skeleton, from Alexei.
2) Stop emitting static variables in skeleton, from Andrii.
3) Low level tc-bpf api, from Kumar.
4) Reduce verifier kmalloc/kfree churn, from Lorenz.
====================
Add BPF_PROG_RUN command as an alias to BPF_RPOG_TEST_RUN to better
indicate the full range of use cases done by the command.
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20210519014032.20908-1-alexei.starovoitov@gmail.com
Add bpf_sys_close() helper to be used by the syscall/loader program to close
intermediate FDs and other cleanup.
Note this helper must never be allowed inside fdget/fdput bracketing.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-11-alexei.starovoitov@gmail.com
Add new helper:
long bpf_btf_find_by_name_kind(char *name, int name_sz, u32 kind, int flags)
Description
Find BTF type with given name and kind in vmlinux BTF or in module's BTFs.
Return
Returns btf_id and btf_obj_fd in lower and upper 32 bits.
It will be used by loader program to find btf_id to attach the program to
and to find btf_ids of ksyms.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-10-alexei.starovoitov@gmail.com
Typical program loading sequence involves creating bpf maps and applying
map FDs into bpf instructions in various places in the bpf program.
This job is done by libbpf that is using compiler generated ELF relocations
to patch certain instruction after maps are created and BTFs are loaded.
The goal of fd_idx is to allow bpf instructions to stay immutable
after compilation. At load time the libbpf would still create maps as usual,
but it wouldn't need to patch instructions. It would store map_fds into
__u32 fd_array[] and would pass that pointer to sys_bpf(BPF_PROG_LOAD).
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-9-alexei.starovoitov@gmail.com
Add placeholders for bpf_sys_bpf() helper and new program type.
Make sure to check that expected_attach_type is zero for future extensibility.
Allow tracing helper functions to be used in this program type, since they will
only execute from user context via bpf_prog_test_run.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210514003623.28033-2-alexei.starovoitov@gmail.com
With the addition of ssi_perf_data and ssi_perf_type struct signalfd_siginfo
is dangerously close to running out of space. All that remains is just
enough space for two additional 64bit fields. A practice of adding all
possible siginfo_t fields into struct singalfd_siginfo can not be supported
as adding the missing fields ssi_lower, ssi_upper, and ssi_pkey would
require two 64bit fields and one 32bit fields. In practice the fields
ssi_perf_data and ssi_perf_type can never be used by signalfd as the signal
that generates them always delivers them synchronously to the thread that
triggers them.
Therefore until someone actually needs the fields ssi_perf_data and
ssi_perf_type in signalfd_siginfo remove them. This leaves a bit more room
for future expansion.
v1: https://lkml.kernel.org/r/20210503203814.25487-12-ebiederm@xmission.com
v2: https://lkml.kernel.org/r/20210505141101.11519-12-ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20210517195748.8880-5-ebiederm@xmission.com
Reviewed-by: Marco Elver <elver@google.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
It turns out that linux uses si_trapno very sparingly, and as such it
can be considered extra information for a very narrow selection of
signals, rather than information that is present with every fault
reported in siginfo.
As such move si_trapno inside the union inside of _si_fault. This
results in no change in placement, and makes it eaiser
to extend _si_fault in the future as this reduces the number of
special cases. In particular with si_trapno included in the union it
is no longer a concern that the union must be pointer aligned on most
architectures because the union follows immediately after si_addr
which is a pointer.
This change results in a difference in siginfo field placement on
sparc and alpha for the fields si_addr_lsb, si_lower, si_upper,
si_pkey, and si_perf. These architectures do not implement the
signals that would use si_addr_lsb, si_lower, si_upper, si_pkey, and
si_perf. Further these architecture have not yet implemented the
userspace that would use si_perf.
The point of this change is in fact to correct these placement issues
before sparc or alpha grow userspace that cares. This change was
discussed[1] and the agreement is that this change is currently safe.
[1]: https://lkml.kernel.org/r/CAK8P3a0+uKYwL1NhY6Hvtieghba2hKYGD6hcKx5n8=4Gtt+pHA@mail.gmail.com
Acked-by: Marco Elver <elver@google.com>
v1: https://lkml.kernel.org/r/m1tunns7yf.fsf_-_@fess.ebiederm.org
v2: https://lkml.kernel.org/r/20210505141101.11519-5-ebiederm@xmission.com
Link: https://lkml.kernel.org/r/20210517195748.8880-1-ebiederm@xmission.com
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
-----BEGIN PGP SIGNATURE-----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=JpHn
-----END PGP SIGNATURE-----
Merge tag 'block-5.13-2021-05-14' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Fix for shared tag set exit (Bart)
- Correct ioctl range for zoned ioctls (Damien)
- Removed dead/unused function (Lin)
- Fix perf regression for shared tags (Ming)
- Fix out-of-bounds issue with kyber and preemption (Omar)
- BFQ merge fix (Paolo)
- Two error handling fixes for nbd (Sun)
- Fix weight update in blk-iocost (Tejun)
- NVMe pull request (Christoph):
- correct the check for using the inline bio in nvmet (Chaitanya
Kulkarni)
- demote unsupported command warnings (Chaitanya Kulkarni)
- fix corruption due to double initializing ANA state (me, Hou Pu)
- reset ns->file when open fails (Daniel Wagner)
- fix a NULL deref when SEND is completed with error in nvmet-rdma
(Michal Kalderon)
- Fix kernel-doc warning (Bart)
* tag 'block-5.13-2021-05-14' of git://git.kernel.dk/linux-block:
block/partitions/efi.c: Fix the efi_partition() kernel-doc header
blk-mq: Swap two calls in blk_mq_exit_queue()
blk-mq: plug request for shared sbitmap
nvmet: use new ana_log_size instead the old one
nvmet: seset ns->file when open fails
nbd: share nbd_put and return by goto put_nbd
nbd: Fix NULL pointer in flush_workqueue
blkdev.h: remove unused codes blk_account_rq
block, bfq: avoid circular stable merges
blk-iocost: fix weight updates of inner active iocgs
nvmet: demote fabrics cmd parse err msg to debug
nvmet: use helper to remove the duplicate code
nvmet: demote discovery cmd parse err msg to debug
nvmet-rdma: Fix NULL deref when SEND is completed with error
nvmet: fix inline bio check for passthru
nvmet: fix inline bio check for bdev-ns
nvme-multipath: fix double initialization of ANA state
kyber: fix out of bounds access when preempted
block: uapi: fix comment about block device ioctl
Now that we have split the multicast router state into two, one for IPv4
and one for IPv6, also add individual timers to the mdb netlink router
port dump. Leaving the old timer attribute for backwards compatibility.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the comment mentioning ioctl command range used for zoned block
devices to reflect the range of commands actually implemented.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Link: https://lore.kernel.org/r/20210509234806.3000-1-damien.lemoal@wdc.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- Expose PLL information per ASIC. This also fixes some casting warnings.
- Skip reading further firmware errors in case PCI link is down.
- Security firmware error should be handled as error and not warning.
- Allow user to ignore firmware errors.
- Fix bug in timeout calculation when waiting for interrupt of CS.
- Fix bug of potential use-after-free.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE7TEboABC71LctBLFZR1NuKta54AFAmCWTaoTHG9nYWJiYXlA
a2VybmVsLm9yZwAKCRBlHU24q1rngMgUB/4gep0fP5vP71R4vsjdlKFkuf/1+b9/
oUJbI5ujWLuJGJpxpv1pZfy/miT4hOIYgxR5jRXa7NJMabW4+PBO7lufif9nsFb9
D4BG/2hAWJLoSdmSlNaRhswScDVjfQBpQPtKBUZPs7YOebNjVCdXBoFwKSFHeWV/
L3zs2/zelCqz8l+F3UFi7Pix+SZCOruah9iAPQaluhQvYEiz6BH5mnz+rm2v7X/X
0/ySpKmtpBcRiL736s9tAZpGjgkfT6Ujdv4qWywX6YPVndoaWLbZlkwm/FGH9SwL
KLE9bx0xi9u1b8bVN4OltV37g4cH7dqfktXYS0AP4S2lnjTkMCoUmzu0
=7Lkr
-----END PGP SIGNATURE-----
Merge tag 'misc-habanalabs-fixes-2021-05-08' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into char-misc-linus
Oded writes:
This tag contains the following fixes for 5.13-rc2:
- Expose PLL information per ASIC. This also fixes some casting warnings.
- Skip reading further firmware errors in case PCI link is down.
- Security firmware error should be handled as error and not warning.
- Allow user to ignore firmware errors.
- Fix bug in timeout calculation when waiting for interrupt of CS.
- Fix bug of potential use-after-free.
* tag 'misc-habanalabs-fixes-2021-05-08' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux:
habanalabs/gaudi: Fix a potential use after free in gaudi_memset_device_memory
habanalabs: wait for interrupt wrong timeout calculation
habanalabs: ignore f/w status error
habanalabs: change error level of security not ready
habanalabs: skip reading f/w errors on bad status
habanalabs: expose ASIC specific PLL index
and netfilter trees. Self-contained fixes, nothing risky.
Current release - new code bugs:
- dsa: ksz: fix a few bugs found by static-checker in the new driver
- stmmac: fix frame preemption handshake not triggering after
interface restart
Previous releases - regressions:
- make nla_strcmp handle more then one trailing null character
- fix stack OOB reads while fragmenting IPv4 packets in openvswitch
and net/sched
- sctp: do asoc update earlier in sctp_sf_do_dupcook_a
- sctp: delay auto_asconf init until binding the first addr
- stmmac: clear receive all(RA) bit when promiscuous mode is off
- can: mcp251x: fix resume from sleep before interface was brought up
Previous releases - always broken:
- bpf: fix leakage of uninitialized bpf stack under speculation
- bpf: fix masking negation logic upon negative dst register
- netfilter: don't assume that skb_header_pointer() will never fail
- only allow init netns to set default tcp cong to a restricted algo
- xsk: fix xp_aligned_validate_desc() when len == chunk_size to
avoid false positive errors
- ethtool: fix missing NLM_F_MULTI flag when dumping
- can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
- sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b
- bridge: fix NULL-deref caused by a races between assigning
rx_handler_data and setting the IFF_BRIDGE_PORT bit
Latecomer:
- seg6: add counters support for SRv6 Behaviors
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=JmWS
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc1, including fixes from bpf, can and
netfilter trees. Self-contained fixes, nothing risky.
Current release - new code bugs:
- dsa: ksz: fix a few bugs found by static-checker in the new driver
- stmmac: fix frame preemption handshake not triggering after
interface restart
Previous releases - regressions:
- make nla_strcmp handle more then one trailing null character
- fix stack OOB reads while fragmenting IPv4 packets in openvswitch
and net/sched
- sctp: do asoc update earlier in sctp_sf_do_dupcook_a
- sctp: delay auto_asconf init until binding the first addr
- stmmac: clear receive all(RA) bit when promiscuous mode is off
- can: mcp251x: fix resume from sleep before interface was brought up
Previous releases - always broken:
- bpf: fix leakage of uninitialized bpf stack under speculation
- bpf: fix masking negation logic upon negative dst register
- netfilter: don't assume that skb_header_pointer() will never fail
- only allow init netns to set default tcp cong to a restricted algo
- xsk: fix xp_aligned_validate_desc() when len == chunk_size to avoid
false positive errors
- ethtool: fix missing NLM_F_MULTI flag when dumping
- can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
- sctp: fix a SCTP_MIB_CURRESTAB leak in sctp_sf_do_dupcook_b
- bridge: fix NULL-deref caused by a races between assigning
rx_handler_data and setting the IFF_BRIDGE_PORT bit
Latecomer:
- seg6: add counters support for SRv6 Behaviors"
* tag 'net-5.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (73 commits)
atm: firestream: Use fallthrough pseudo-keyword
net: stmmac: Do not enable RX FIFO overflow interrupts
mptcp: fix splat when closing unaccepted socket
i40e: Remove LLDP frame filters
i40e: Fix PHY type identifiers for 2.5G and 5G adapters
i40e: fix the restart auto-negotiation after FEC modified
i40e: Fix use-after-free in i40e_client_subtask()
i40e: fix broken XDP support
netfilter: nftables: avoid potential overflows on 32bit arches
netfilter: nftables: avoid overflows in nft_hash_buckets()
tcp: Specify cmsgbuf is user pointer for receive zerocopy.
mlxsw: spectrum_mr: Update egress RIF list before route's action
net: ipa: fix inter-EE IRQ register definitions
can: m_can: m_can_tx_work_queue(): fix tx_skb race condition
can: mcp251x: fix resume from sleep before interface was brought up
can: mcp251xfd: mcp251xfd_probe(): add missing can_rx_offload_del() in error path
can: mcp251xfd: mcp251xfd_probe(): fix an error pointer dereference in probe
netfilter: nftables: Fix a memleak from userdata error path in new objects
netfilter: remove BUG_ON() after skb_header_pointer()
netfilter: nfnetlink_osf: Fix a missing skb_header_pointer() NULL check
...
Currently the user cannot interpret the PLL information based on index
as its exposed as an integer.
This commit exposes ASIC specific PLL indexes and maps it to a generic
FW compatible index.
Signed-off-by: Bharat Jauhari <bjauhari@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
Geliang Tang
Andrea Mayer
David S. Miller
Jian Shen
Guvenc Gulce
Kuniyuki Iwashima
Johannes Berg
Arseny Krasnov
Chen Li
Florian Westphal
Andreas Roeseler
Marcel Holtmann
Dmytro Linkin
Sharath Chandra Vurukala
Phil Sutter
Jakub Kicinski
Oliver Hartkopp
Marc Kleine-Budde
Hangbin Liu
Denis Salopek
Linus Torvalds
Alexei Starovoitov
Eric W. Biederman
Linus Lüssing
Damien Le Moal
Greg Kroah-Hartman
Bharat Jauhari