As noted by pl bossart <bossart.nospam@gmail.com>, the PCM I/O routines
(snd_pcm_lib_write1, snd_pcm_lib_read1) should block wake_up() calls
until all samples are not processed.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Do general cleanup in snd_pcm_update_hw_ptr*() routines and merge them.
The main change is hw_ptr_interrupt variable removal to simplify code
logic. This variable can be computed directly from hw_ptr.
Ensure that updated hw_ptr is not lower than previous one (it was possible
with old code in some obscure situations when interrupt was delayed or
the lowlevel driver returns wrong ring buffer position value).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In some debug cases, it might be usefull to see previous ring buffer
positions to determine position problems from the lowlevel drivers.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It is called LBDAF since 2.6.31.
impact:
without this change, on 32bit,
DRBD would wrongly claim to only support 2TiB devices.
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Stanse found an unreachable statement in reiserfs_ioctl. There is a
if followed by error assignment and `break' with no braces. Add the
braces so that we don't break every time, but only in error case,
so that REISERFS_IOC_SETVERSION actually works when it returns no
error.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Reiserfs <reiserfs-devel@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
reiserfs_get_acl is usually not called under the reiserfs lock,
as it doesn't need it. But it happens when it is called by
reiserfs_acl_chmod(), which creates a dependency inversion against
the private xattr inodes mutexes for the given inode.
We need to call it without the reiserfs lock, especially since
it's unnecessary.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Alexander Beregalov <a.beregalov@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
For configurations where Synaptics hardware is present but the Synaptics
extensions support is not compiled in, the mouse is reprobed and a new
device is allocated on every suspend/resume.
During probe, psmouse_switch_protocol() calls psmouse_extensions() with
set_properties=1. This calls the dummy synaptics_init() which returns an
error code, instructing us not to use the synaptics extensions.
During resume, psmouse_reconnect() calls psmouse_extensions() with
set_properties=0, in which case call to synaptics_init() is bypassed and
PSMOUSE_SYNAPTICS is returned. Since the result is different from previous
attempt psmouse_reconnect() fails and full re-probe happens.
Fix this by tweaking the set_properties=0 codepath in psmouse_extensions()
to be more careful about offering PSMOUSE_SYNAPTICS extensions.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address and mask.
The only difference in the output is that the output is shown in
the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NET_SKB_PAD is not a multiple of the cache line size, mv643xx_eth
allocates a couple of extra bytes at the start of each receive buffer
to make the data payload end up on a cache line boundary.
These extra bytes are skb_reserve()'d before DMA mapping, so they
should not be included in the DMA map byte count (as the mapping is
done starting at skb->data), nor should they be included in the
receive descriptor buffer size field, or the hardware can end up
DMAing beyond the end of the buffer, which can happen if someone
sends us a larger-than-MTU sized packet.
This problem was introduced in commit 7fd96ce47f ("mv643xx_eth:
rework receive skb cache alignment", May 6 2009), but hasn't appeared
to be problematic so far, probably as the main users of mv643xx_eth
all have NET_SKB_PAD == L1_CACHE_BYTES.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A failure on request_irq() is always fatal but unlike other fatal
errors it's only reported to the user if net_debug is set. Make the
diagnostic unconditional and raise the priority so that errors are
more obvious to the user.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The contents of /proc/net/dev is annoying to parse, because
it changes whether there is a space after the "ethX:" or not.
It depends upon the size of the "Receive bytes" counter,
if the number is below 7 digits, then there is whitespaces
else if the number is 8 digits or above there is no space
between the ":" and the number.
This patch changes the output to assure there is always a space
between the ":" and the number. Given that all existing userspace
application already need to handle the whitespaces, I see
no breakage of existing tools.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to be used together with switch technologies, like RFC3069,
that where the individual ports are not allowed to communicate with
each other, but they are allowed to talk to the upstream router. As
described in RFC 3069, it is possible to allow these hosts to
communicate through the upstream router by proxy_arp'ing.
This patch basically allow proxy arp replies back to the same
interface (from which the ARP request/solicitation was received).
Tunable per device via proc "proxy_arp_pvlan":
/proc/sys/net/ipv4/conf/*/proxy_arp_pvlan
This switch technology is known by different vendor names:
- In RFC 3069 it is called VLAN Aggregation.
- Cisco and Allied Telesyn call it Private VLAN.
- Hewlett-Packard call it Source-Port filtering or port-isolation.
- Ericsson call it MAC-Forced Forwarding (RFC Draft).
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Wed, Jan 06, 2010 at 10:10:03PM +0100, Eric Dumazet wrote:
> Le 06/01/2010 19:38, Eric Dumazet a écrit :
> >
> > (net-next-2.6 doesnt work well on my bond/vlan setup, I suspect I need a bisection)
>
> David, I had to revert 1f3c8804ac
> (bonding: allow arp_ip_targets on separate vlans to use arp validation)
>
> Or else, my vlan devices dont work (unfortunatly I dont have much time
> these days to debug the thing)
>
> My config :
>
> +---------+
> vlan.103 -----+ bond0 +--- eth1 (bnx2)
> | +
> vlan.825 -----+ +--- eth2 (tg3)
> +---------+
>
> $ cat /proc/net/bonding/bond0
> Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009)
>
> Bonding Mode: fault-tolerance (active-backup)
> Primary Slave: None
> Currently Active Slave: eth2
> MII Status: up
> MII Polling Interval (ms): 100
> Up Delay (ms): 0
> Down Delay (ms): 0
>
> Slave Interface: eth1 (bnx2)
> MII Status: down
> Link Failure Count: 1
> Permanent HW addr: 00:1e:0b:ec:d3:d2
>
> Slave Interface: eth2 (tg3)
> MII Status: up
> Link Failure Count: 0
> Permanent HW addr: 00:1e:0b:92:78:50
>
This patch fixes up a problem with found with commit
1f3c8804ac. The original change
overloaded null_or_orig, but doing that prevented any packet handlers
that were not tied to a specific device (i.e. ptype->dev == NULL) from
ever receiving any frames.
The null_or_orig variable cannot be overloaded, and must be kept as NULL
to prevent the frame from being ignored by packet handlers designed to
accept frames on any interface.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed missing newlines in calls to dev_warn & dev_err.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't send flow control settings to any port other than the modem port.
Older firmware ignored this request but did sent a reply. Newer firmware just
ignores it without reply and causes a 5 second timeout every time a port
(except for the modem port) is opened or if tiocm settings are changed.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to reset the usb device when we receive usb bus errors.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't change the state of a port if it's not open. This fixes an issue where a
port sometimes has to be opened twice before data can be received.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields are always little endian and have to be converted on big endian
machines.
Signed-off-by: Jan Dumon <j.dumon@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The id_table field of the struct pci_driver is constant in <linux/pci.h>
so it is worth to make pci_device_id also constant.
The semantic match that finds this kind of pattern is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier I1, I2, x;
@@
struct I1 {
...
const struct I2 *x;
...
};
@s@
identifier r.I1, y;
identifier r.x, E;
@@
struct I1 y = {
.x = E,
};
@c@
identifier r.I2;
identifier s.E;
@@
const struct I2 E[] = ... ;
@depends on !c@
identifier r.I2;
identifier s.E;
@@
+ const
struct I2 E[] = ...;
// </smpl>
Signed-off-by: Márton Németh <nm127@freemail.hu>
Cc: Julia Lawall <julia@diku.dk>
Cc: cocci@diku.dk
Signed-off-by: David S. Miller <davem@davemloft.net>
Claw module cannot be loaded together with qeth, because "qeth" has
been errorneously used as root device name. It is changed into "claw".
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Send aligned pipe payload if requested to do so. Then, the socket buffer
needs not be fragmented anymore.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer Nokia cellular modems can use aligned payload for their GPRS pipe.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_err(), dev_warn() and dev_dbg() ensure consistency in driver messages.
Also switch to using bool where appropriate and fix some formatting issues.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds a parallel crypto template that takes a crypto
algorithm and converts it to process the crypto transforms in
parallel. For the moment only aead algorithms are supported.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use #include <linux/ not #include <asm/
Add spaces after arguments
Comment neatening
Make a couple of arrays static const
Align function arguments
Wrap text at 80 columns where reasonable
Cuddle brace else
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use printk_once
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert printks without KERN_<level> to pr_info and pr_cont
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
