Today's -tip failed to build because commit
9e368fa011 ("ipmi: add PNP discovery (ACPI
namespace via PNPACPI)") from today's upstream kernel causes the following
build failure on x86, for CONFIG_ACPI=n && CONFIG_IPMI_SI=y:
drivers/char/ipmi/ipmi_si_intf.c:3208: error: 'ipmi_pnp_driver' undeclared (first use in this function)
drivers/char/ipmi/ipmi_si_intf.c:3208: error: (Each undeclared identifier is reported only once
drivers/char/ipmi/ipmi_si_intf.c:3208: error: for each function it appears in.)
drivers/char/ipmi/ipmi_si_intf.c:3334: error: 'ipmi_pnp_driver' undeclared (first use in this function)
The reason is that the ipmi_pnp_driver depends on ACPI facilities and is only
made available under ACPI - while the registration and unregistration is made
dependent on CONFIG_PNP:
#ifdef CONFIG_PNP
pnp_register_driver(&ipmi_pnp_driver);
#endif
The solution is to only register this driver under ACPI. (Also, the CONFIG_PNP
dependency is not needed because pnp_register_driver() is stubbed out in the
!CONFIG_PNP case.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This fixes a bug (found by Curt Wohlgemuth) in which new blocks
returned from an extent created with ext4_ext_zeroout() can have dirty
metadata still associated with them.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Curt Wohlgemuth <curtw@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
If two arrays share a device, then they will not both resync at the
same time. One will wait for the other to complete.
While waiting, the MD_RECOVERY_INTR flag is not checked so a device
failure, which would make the resync pointless, does not cause the
resync to abort, so the failed device cannot be removed (as it cannot
be remove while a resync is happening).
So add a test for MD_RECOVERY_INTR.
Reported-by: Brett Russ <bruss@netezza.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit dfc7064500,
->hot_remove_disks has not removed non-failed devices from
an array until recovery is no longer possible.
So the code in do_md_run to get around the fact that
md_check_recovery (which calls ->hot_remove_disks) would
remove partially-in-sync devices is no longer needed.
So remove it.
Signed-off-by: NeilBrown <neilb@suse.de>
By default md_do_sync() will perform recovery if no other actions are
specified. However, action_show() relies on MD_RECOVERY_RECOVER to be
set otherwise it returns 'idle'. So, add a missing set
MD_RECOVERY_RECOVER when starting recovery.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The start_ro modules parameter can be used to force arrays to be
started in 'auto-readonly' in which they are read-only until the first
write. This ensures that no resync/recovery happens until something
else writes to the device. This is important for resume-from-disk
off an md array.
However if an array is started 'readonly' (by writing 'readonly' to
the 'array_state' sysfs attribute) we want it to be really 'readonly',
not 'auto-readonly'.
So strengthen the condition to only set auto-readonly if the
array is not already read-only.
Signed-off-by: NeilBrown <neilb@suse.de>
Use the %pM kernel extension to display the MAC address.
The only difference in the output is that the MAC address is
shown in the usual colon-separated hex notation instead of
space-separated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
evms configures md arrays by:
open device
send ioctl
close device
for each different ioctl needed.
Since 2.6.29, the device can disappear after the 'close'
unless a significant configuration has happened to the device.
The change made by "SET_ARRAY_INFO" can too minor to stop the device
from disappearing, but important enough that losing the change is bad.
So: make sure SET_ARRAY_INFO sets mddev->ctime, and keep the device
active as long as ctime is non-zero (it gets zeroed with lots of other
things when the array is stopped).
This is suitable for -stable kernels since 2.6.29.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: stable@kernel.org
Commit 500f5a0bf5
(reiserfs: Fix possible recursive lock) fixed a vmalloc under reiserfs
lock that triggered a lockdep warning because of a
IN-FS-RECLAIM <-> RECLAIM-FS-ON locking dependency inversion.
But this patch has ommitted another vmalloc call in the same path
that allocates the journal. Relax the lock for this one too.
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Chris Mason <chris.mason@oracle.com>
Cc: Ingo Molnar <mingo@elte.hu>
Update the Kconfig help texts of both stacks to encourage a general move
from the older to the newer drivers. However, do not label ieee1394 as
"Obsolete" yet, as the newer drivers have not been deployed as default
stack in the majority of Linux distributions yet, and those who start
doing so now may still want to install the old drivers as fallback for
unforeseen issues.
Since Linux 2.6.32, FireWire audio devices can be driven by the newer
firewire driver stack too, hence remove an outdated comment about audio
devices. Also remove comments about library versions since the 2nd
generation of libraw1394 and libdc1394 is now in common use; details on
library versions can be read at the wiki link from the help texts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Ben and Kristian have not been involved in maintenance of the IEEE 1394
drivers for quite some time; submitters are not required to Cc them on
patches.
The linux1394.org domain has been dead for a while and is no longer
under control of a Linux developer. The current web site of the
Linux 1394 project is http://ieee1394.wiki.kernel.org/.
The classic drivers/ieee1394/ stack is now obsolete from the development
point of view, though still a useful alternative in productive use. But
nobody should attempt to submit style cleanup patches for it or to
develop new drivers on top of this stack, hence mark its MAINTAINERS
entry as Obsolete.
drivers/ieee1394/raw1394*, like the rest of the old stack, does not
receive bigger code changes anymore, hence shrink the MAINTAINERS
database a bit by dropping raw1394's special entry. If something
important and urgent is going to come up for raw1394, I will make sure
that Dan will be notified of it besides via linux1394-devel.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Dan Dennedy <dan@dennedy.org>
Cc: Ben Collins <ben.collins@ubuntu.com>
Cc: Kristian Hoegsberg <krh@bitplanet.net>
This is a minimal change meant for the short term: Never set the
ohci->use_dualbuffer flag to true.
There are two reasons to do so:
- Packet-per-buffer mode and dual-buffer mode do not behave the same
under certain circumstances, notably if several packets are covered
by a single fw_cdev_iso_packet descriptor.
http://marc.info/?l=linux1394-devel&m=124965653718313
Therefore the driver stack should not silently choose one or the
other mode but should leave the choice to the high-level driver
(regardless if kernel driver or userspace driver). Or simply always
only offer packet-per-buffer mode, since a considerable number of
controllers, even current ones, does not offer dual-buffer support.
- Even under circumstances where packet-per-buffer mode and
dual-buffer mode behave exactly the same --- notably when used
through libraw1394, libdc1394, as well as the current two kernel
drivers which use isochronous reception (firewire-net and firedtv)
--- we are still faced with the problem that several OHCI 1.1
controllers have bugs in dual-buffer mode. Although it looks like
we have identified most of those buggy controllers by now, we
cannot be quite sure about that.
So, use packet-per-buffer by default from now on. This change should
be followed up by a more complete solution: Either extend the
in-kernel API and the userspace ABI by a choice between the two IR modes
or remove all dual-buffer related code from firewire-ohci.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If copy_from_user in an FW_CDEV_IOC_SEND_RESPONSE ioctl failed, the
fw_request pointed to by the inbound_transaction_resource is no
longer referenced and needs to be freed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Control of more than one AV/C device at once --- e.g. camcorders, tape
decks, audio devices, TV tuners --- failed or worked only unreliably,
depending on driver implementation. This affected kernelspace and
userspace drivers alike and was caused by firewire-core's inability to
accept multiple registrations of FCP listeners.
The fix allows multiple address handlers to be registered for the FCP
command and response registers. When a request for these registers is
received, all handlers are invoked, and the Firewire response is
generated by the core and not by any handler.
The cdev API does not change, i.e., userspace is still expected to send
a response for FCP requests; this response is silently ignored.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (changelog, rebased, whitespace)
!CONFIG_OPT evalues to FALSE if CONFIG_OPT='m'. Do not display the
"DRBD disabled..." message if the dependencies are compiled as module.
Signed-off-by: Johannes Thoma <johannes.thoma@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
In D_DISKLESS we do not hand out any new references to ldev (local_cnt)
therefore waiting until all previously handed out refereces got returned
is sufficient before actually freeing mdev->ldev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
queue_sector_alignment_offset returned the wrong value which caused
partitions to report an incorrect alignment_offset. Since offset
alignment calculation is needed several places it has been split into a
separate helper function. The topology stacking function has been
updated accordingly.
Furthermore, comments have been added to clarify how the stacking
function works.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
PXA mmc host driver supports card detect, read only and power gpio pin
setting already. Zylonite platform driver needn't implement this any more.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
DM9000s on Zeus sometime fail under heavy load.
Relaxing the timings a bit seems to be of a great help.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This has to be selected, otherwise some peripherals don't get initialized.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit "d2a34c1 drivers/video: Move dereference after NULL test" introduced
a build error of "fbi->dev->platform_data->smart_update" being unknown type
to the compiler, fix this by removing the unnecessary test of 'fbi'.
Cc: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The wrong address was being used to write the SCIR led regs on
remote hubs. Also, there was an inconsistency between how BIOS
and the kernel indexed these regs. Standardize on using the
lower 6 bits of the APIC ID as the index.
This patch fixes the problem of writing to an errant address to
a cpu # >= 64.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Jack Steiner <steiner@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@kernel.org
LKML-Reference: <4B3922F9.3060905@sgi.com>
[ v2: fix a number of annoying checkpatch artifacts and whitespace noise ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The PCIe inbound window size is supposed to be a power of two. If
the total amount of RAM installed in the system is not a power of two,
round it up such that it is.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
As CPUs are migrated over to more fully-featured clock frameworks of
their own and off of the legacy CPG code, they no longer have any real
need for defining the PCLK value. The PCLK define in itself is already
fairly misleading, as many boards get their input clocks from different
sources, making this value fairly arbitrary anyways.
Outside of the legacy CPG clock framework, the only place where this
value is used is for deriving CLOCK_TICK_RATE, which we set back to the
legacy PIT value that it was before the PCLK definitions were added in
the first place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.
mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to be requeueing the work struct
since we check for the scan after removing items
due to possible timeouts.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
