We were forcing the PCS link up in error when we are in KX mode. We should
only be disabling autoneg, not forcing the link up.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SN06 makes sure we get back a longer buffer which seems to be necessary
going forward as the SNC devices describes more and more devices (or
features more precisely). Moreover SN06 should be called with only the
descriptor offset to make sure we hit the rfkill controlling function
(F124 or F135) with a 0 argument to get a full list of features.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Tested-by: Miguel Rodríguez Pérez <miguelrp@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Vaio Type X and possibly other new models use F135 as the radio
frequency controlling function attached to the SNC device. In the
indexed table this corresponds to 0x0135 (surpise!).
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
This hardware watchdog can misfire, so it does more harm than good.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some cables have EEPROMs that conflict with the PHY's on-board EEPROM
so it cannot load firmware.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's firmware very occasionally appears to lock up very early, but
with the heartbeat update still running. Rebooting the microcontroller
core seems to be sufficient to recover.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY boots in a mode which is not necessarily optimal. This change
switches it to self-configure mode (except when in loopback, which
won't work in that mode if an SFP+ module is not present) by rebooting
the PHY's microcontroller, and replicating the sequence of configuration
writes from the boot EEPROM with the appropriate changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we see the PHY remaining stuck in a link-down state due to PCS being
down while PMA/PMD is up, we briefly switch to PMA/PMD loopback and back,
which usually unsticks it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need buffer->len to remain valid to work out the correct address to
be unmapped. We therefore need to clear buffer->len after the unmap
operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGXS block may not get a link immediately in XGXS or XAUI loopback
modes, so we still need to check it. Split falcon_xaui_link_ok() into
falcon_xgxs_link_ok(), which checks only the Falcon XGXS block, and
falcon_xmac_link_ok(), which checks one or both sides of the link as
appropriate. Also rename falcon_check_xaui_link() to
falcon_xmac_link_ok_retry().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This prevents efx->link_advertising from being blatted during
a reset.
The phy_short_reach sysfs node is now destroyed later in the
port shutdown process, so check for STATE_RUNNING after
acquiring the rtnl_lock (just like in set_phy_flash_cfg).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'i2c-fixes' of git://git.fluff.org/bjdooks/linux:
i2c-omap: OMAP3: Fix I2C lockup during timeout/error cases
i2c-omap: Don't write IE state in unidle if 0
i2c-bfin-twi: fix CLKDIV calculation
In ocfs2_value_metas_in_xattr_header, we should Use
le16_to_cpu for ocfs2_extent_list.l_next_free_rec.
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
I just noticed today that there are 2 places of "mlog(0,...)"
in fs/ocfs2/cluster/heartbeat.c, but actually have no default
mask prefix in that file.
So change them to mlog(ML_HEARTBEAT,...).
Signed-off-by: Tao Ma <tao.ma@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
For fast symlink, it can be treated the same as inlined files since
the data extent we want to return of both case all were stored in
metadata block. For symlink, it can be simply treated the same as we
did for regular files.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>
Acked-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Current OMAP3 I2C driver code does not follow the correct sequence for soft
reset. Due to this, lock up issues are reported during timeout/error cases.
This patch fixes above issue by disabling I2C controller as per OMAP3430 TRM
for soft reset. As per TRM, I2C controller needs to be disabled as a first
step during soft reset.
Here is correct soft reset sequence:
a. Ensure that the module is disabled
(clear the I2Ci.I2C_CON[15] I2C_EN bit to 0).
b. Set the I2Ci.I2C_SYSC[1] SRST bit to 1.
c. Enable the module by setting I2Ci.I2C_CON[15] I2C_EN bit to 1.
d. Check the I2Ci.I2C_SYSS[0] RDONE bit until it is set to 1 to
indicate the software reset is complete.
Tested on Zoom2, Zoom3, 3430SDP and 3630SDP
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: George, Harith<harith@ti.com>
Acked-by: Varadarajan, Charu Latha<charu@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit ef871432... (i2c-omap: OMAP3: PM: (re)init for every transfer
to support off-mode) introduced a change which make the dev->iestate
contents be written to the OMAP_I2C_IE_REG every time omap_i2c_unidle
is called. Previously, the state was only written if it wasn't equal
to zero.
In omap_i2c_probe, omap_i2c_unidle() is called prior to omap_i2c_init(),
in which case dev->iestate has not yet been initialized and will be set
to zero. Having this value written to the registers causes deadlock
while booting.
As such, this change restores the original functionality.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Calculation of the CLKDIV speed setting should be done using base 10 math
rather than base 2. We also avoid exceeding the spec due to integer
truncation and a 50% duty cycle.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] use resource_size()
[WATCHDOG] iTCO_wdt: add PCI ID for the Intel EP80579 (Tolapai) SoC
This reverts commit 9f15226e75. It's just
wrong, and broke resume for Rafael even on a non-AMD CPU.
As Rafael says:
"... it causes microcode_init_cpu() to be called during resume even for
CPUs for which there's no microcode to apply. That, in turn, results
in executing request_firmware() (on Intel CPUs at least) which doesn't
work at this stage of resume (we have device interrupts disabled, I/O
devices are still suspended and so on).
If I'm not mistaken, the "if (uci->valid)" logic means "if that CPU is
known to us" , so before commit 9f15226e75 microcode_resume_cpu() was
called for all CPUs already in the system during suspend, which was
the right thing to do. The commit changed it so that the CPUs without
microcode to apply are now treated as "unknown", which is not quite
right.
The problem this commit attempted to solve has to be handled
differently."
Bisected-and -requested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Executing _OSC returns a buffer, which has an acpi object in it.
Don't directly returns the buffer, instead, we return the acpi object's
buffer. This fixes a regression since caller of acpi_run_osc expects
an acpi object's buffer returned.
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
1. remove address argument since we use same address IWMC_SDIO_DATA_ADDR in
all cases
2. add __iwmct_tx - non locking tx function for already locked contexts
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. add TRACE level
2. use TRACE where needed to reduce the noise
3 don't INFOEX from driver
4. add DUMP level for packets dumps
5. use correct context for the log messages
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. removed redundant NULL-pointers checks in iwmct_fw_load
as release_firmware and kfree are NULL pointer friendly
2. remove redundant memset of the parser since the structure
is fully initialized in iwmct_fw_parser_init function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtnetlink init_rcvwnd to set the TCP initial receive window size
advertised by passive and active TCP connections.
The current Linux TCP implementation limits the advertised TCP initial
receive window to the one prescribed by slow start. For short lived
TCP connections used for transaction type of traffic (i.e. http
requests), bounding the advertised TCP initial receive window results
in increased latency to complete the transaction.
Support for setting initial congestion window is already supported
using rtnetlink init_cwnd, but the feature is useless without the
ability to set a larger TCP initial receive window.
The rtnetlink init_rcvwnd allows increasing the TCP initial receive
window, allowing TCP connection to advertise larger TCP receive window
than the ones bounded by slow start.
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non-GSO code drops dst entry for performance reasons, but
the same is missing for GSO code. Drop dst while cache-hot
for GSO case too.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly optimize tcp_sendmsg since NETIF_F_SG is used many
times iteratively in the loop. The only other modification is
to change:
} else if (i == MAX_SKB_FRAGS ||
(!i &&
!(sk->sk_route_caps & NETIF_F_SG))) {
to:
} else if (i == MAX_SKB_FRAGS || !sg) {
The reason why this change is correct: this code (other than
the MAX_SKB_FRAGS case) executes only due to the else part
of: "if (skb_tailroom(skb) > 0) {" - i.e. there was no space
in the skb to put the data inline. Hence SG is false is a
sufficient condition, and there is no way a fragment can be
added to the skb.
Changelog:
- Added the above explanation for the change
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unrequired operations in tcp_push()
Changelog:
Removed a temporary skb variable from tcp_push()
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_push checks tcp_send_head and calls __tcp_push_pending_frames,
which again checks tcp_send_head, and this unnecessary check is
done for every other caller of __tcp_push_pending_frames.
Remove tcp_send_head check in __tcp_push_pending_frames and add
the check to tcp_push_pending_frames. Other functions call
__tcp_push_pending_frames only when tcp_send_head would evaluate
to true.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support pci error detection and recovery.
o Refactor suspend and resume code, to share with io_error_detected,
and slot_reset callbacks
o NX_NEED_AER device state added, to synchronize with firmware
recovery.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case of tx timeout, firmare may be healthy, but some pci-func may
see no response from it. Force firmware reset, if some pci-func
explicitly requests so.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o pci device should be disable at the end and it should be enable first.
o Interface should be attached(netif_device_attach()) irrespective
of its state.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (30 commits)
USB: Fix a bug on appledisplay.c regarding signedness
USB: option: support hi speed for modem Haier CE100
USB: audio gadget: free alsa devices when unloading
USB: audio gadget: fix wTotalLength calculation
usb: otg: isp1301_omap: fix compile error
USB: musb: workaround Blackfin FIFO anomalies
USB: musb: Fix array index out of bounds issue
USB: musb: Fix null pointer dereference issue
USB: musb: correct DMA address for tx
USB: musb: gadget_ep0: avoid SetupEnd interrupt
USB: musb: fix for crash in DM646x USB when (CPPI)DMA is enabled
USB: musb: do not work if no gadget driver is loaded
USB: musb: gadget: set otg tranceiver to idle when registering gadget
USB: musb: Populate the VBUS GPIO with the correct GPIO number
USB: musb: MAINTAINERS: Fix my tree's address
USB: musb: fix compiling warning with min() macro
USB: musb: move musb_remove to __exit
USB: musb_gadget: fix kernel oops in txstate()
USB: ftdi_sio: sort PID/VID entries in new ftdi_sio_ids.h header
USB: ftdi_sio: isolate all device IDs to new ftdi_sio_ids.h header
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
devtmpfs: unlock mutex in case of string allocation error
Driver core: export platform_device_register_data as a GPL symbol
driver core: Prevent reference to freed memory on error path
Driver-core: Fix bogus 0 error return in device_add()
Driver core: driver_attribute parameters can often be const*
Driver core: bin_attribute parameters can often be const*
Driver core: device_attribute parameters can often be const*
Doc/stable rules: add new cherry-pick logic
vfs: get_sb_single() - do not pass options twice
devtmpfs: Convert dirlock to a mutex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging/vt66*: kconfig, depends on WLAN
Staging: batman-adv: introduce missing kfree
Staging: batman-adv: Add Kconfig dependancies on PROC_FS and PACKET.
Staging: panel: Adjust range for PANEL_KEYPAD in Kconfig
Staging: panel: Fix compilation error with custom lcd charset
Staging: ramzswap: remove ARM specific d-cache hack
Staging: rtl8192x: fix printk formats
Staging: wlan-ng: fix Correct size given to memset
staging: rtl8192su: add USB VID/PID for HWNUm-300
staging: fix rtl8192su compilation errors with mac80211
staging: fix rtl8192e compilation errors with mac80211
Staging: fix rtl8187se compilation errors with mac80211
Staging: rtl8192su: fix test for negative error in rtl8192_rx_isr()
Staging: comedi: jr3_pci: Don't ioremap too much space. Check result.
Staging: comedi: removed "depricated" from COMEDI_CB_BLOCK
Staging: comedi: usbdux.c: fix locking up of the driver when the comedi ringbuffer runs empty
Staging: dst: remove from the tree
Staging: sm7xx: add a new framebuffer driver
Staging: batman: fix debug Kconfig option
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Set i_nlink properly during reflink.
ocfs2: Add reflinked file's inode to inode hash eariler.
ocfs2: refcounttree.c cleanup.
ocfs2: Find proper end cpos for a leaf refcount block.
Fix two bugs in s3c_nand_set_platdata() where thet device's platform
data was not set, and the wrong error check was being performed on
the return of s3c_nand_copy_set().
Fixes the following OOPS:
Unable to handle kernel NULL pointer dereference at virtual address 00000004
PC is at s3c24xx_nand_probe+0x234/0x594
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The zone list code clearly cannot tolerate concurrent writers (I couldn't
find any locks for that), so simply add a global mutex. No need for RCU
in this case.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
When printing legacy sysctls print the warning message
for each of them only once. This way there is a guarantee
the syslog won't be flooded for any sane program.
The original attempt at this made the tables non const and stored
the flag inline.
Linus suggested using a separate hash table for this, this is based on a
code snippet from him.
The hash implies this is not exact and can sometimes not print a
new sysctl due to a hash collision, but in practice this should not
be a problem
I used a FNV32 hash over the binary string with a 32byte bitmap. This
gives relatively little collisions when all the predefined binary sysctls
are hashed:
size 256
bucket
length number
0: [25]
1: [67]
2: [88]
3: [47]
4: [22]
5: [6]
6: [1]
The worst case is a single collision of 6 hash values.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
It is unpredictable to have the same memory mapped using different
shared bit settings for ARMv6 and ARMv7 CPUs. Fix this for the CPU
write buffer bug test.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
brightness status is reported by the Apple Cinema Displays as an
'unsigned char' (u8) value, but the code used 'char' instead.
Note that he driver was developed on the PowerPC architecture,
where the two types are synonymous, which is not always the case.
Fixed that. Otherwise the driver will interpret brightness
levels > 127 as negative, and fail to load.
Signed-off-by: pancho horrillo <pancho@pancho.name>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The wTotalLength should contain the sum of the interface and unit
descriptor sizes per the Audio Device Class specification 1.0.
Reported-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 91c8a5a998 broke
compilation of this driver after it introduced
otg_init() as a static inline in <linux/usb/otg.h>
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of these workarounds are already in place, but labeled as affecting
all BF52x parts. Since we have official anomaly numbers now, use those
defines. And since writing to the FIFO has a similar hang issue as reading
from the FIFO, implement the workaround there too when necessary.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
