Hi Liam,
Since Samuel merged a new version of mfd 88pm8607 driver, I format a
new patch on regulator 88pm8607. I paste the new patch in mail. Please
help to review again. And I also attach the mfd driver in mail.
From: Haojian Zhuang <haojian.zhuang@marvell.com>
Date: Thu, 8 Oct 2009 09:36:53 -0400
Subject: [PATCH] regulator: Add 88PM8607 PMIC driver
This patch adds regulator drivers for Marvell 88PM8607 PMIC.
This controller contains 3 DVC and 14 LDO regulators. This controller
uses I2C interface.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.
This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.
Configuration of the DVS MFP on the device should be done externally,
for example via OTP.
Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It's just wasteful for stacktrace users like perf to walk
through every entries on the stack whereas these only accept
reliable ones, ie: that the frame pointer validates.
Since perf requires pure reliable stacktraces, it needs a stack
walker based on frame pointers-only to optimize the stacktrace
processing.
This might solve some near-lockup scenarios that can be triggered
by call-graph tracing timer events.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-2-git-send-regression-fweisbec@gmail.com>
[ v2: fix for modular builds and small detail tidyup ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The current print_context_stack helper that does the stack
walking job is good for usual stacktraces as it walks through
all the stack and reports even addresses that look unreliable,
which is nice when we don't have frame pointers for example.
But we have users like perf that only require reliable
stacktraces, and those may want a more adapted stack walker, so
lets make this function a callback in stacktrace_ops that users
can tune for their needs.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1261024834-5336-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since nothing includes the <linux/perf_counter.h> file and it's
also not exported to user space, remove it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <alpine.LFD.2.00.0912161007430.8198@localhost>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In practice, it is harmless to voluntarily sleep in a
rcu_read_lock() section if we are running under preempt rcu, but
it is illegal if we build a kernel running non-preemptable rcu.
Currently, might_sleep() doesn't notice sleepable operations
under rcu_read_lock() sections if we are running under
preemptable rcu because preempt_count() is left untouched after
rcu_read_lock() in this case. But we want developers who test
their changes under such config to notice the "sleeping while
atomic" issues.
So we add rcu_read_lock_nesting to prempt_count() in
might_sleep() checks.
[ v2: Handle rcu-tiny ]
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1260991265-8451-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix libdwarf include path to fit debian-like systems too.
Borislav Petkov reported:
> even after installing libdwarf-dev on my debian box here,
> make in tools/perf/ still complains that it cannot find libdwarf:
>
> Makefile:491: No libdwarf.h found or old libdwarf.h found, disables dwarf
> support. Please install libdwarf-dev/libdwarf-devel >= 20081231
>
> The problem is that the include path on debian is not
> /usr/include/libdwarf/ but simply /usr/include because the debian
> package libdwarf-dev puts the headers straight into
> /usr/include.
This patch adds -I/usr/include/libdwarf to BASIC_CFLAGS
and fix probe-finder.h to include just libdwarf.h/dwarf.h.
This patch also adds a workaround for the undefined _MIPS_SZLONG
bug in libdwarf.h.
Reported-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Gabor Gombas <gombasg@sztaki.hu>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
LKML-Reference: <20091216221618.13816.83296.stgit@dhcp-100-2-132.bos.redhat.com>
[ v2: small stylistic fixlets to probe-finder.h ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove !ap test, where ap is guaranteed not-NULL. Found by way of automated
bug report from Alexander Strakh via "Linux Device Drivers Verification
Project (Svace Detector)"
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The clock turnaround code still doesn't work for several reasons:
- 'USE_DPLL' flag in 'ap->host->private_data' is never initialized
or updated, so the driver can only set the chip to the DPLL clock
mode, not the PCI mode;
- the driver doesn't serialize access to the channels depending on
the current clock mode like the vendor drivers, so the clock
turnaround is only executed "optionally", not always as it should be;
- the wrong ports are written to when hpt3x2n_set_clock() is called
for the secondary channel;
- hpt3x2n_set_clock() can inadvertently enable the disabled channels
when resetting the channel state machines.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When we drain data from a device to clear DRQ during error recovery,
the number of bytes reported as drained is too low by a factor of 2
because the count is actually reporting the number of words drained,
not bytes. Fix this.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It appears the size for cs1 is calculated using the wrong resource.
Use the function resource_size to get the correct value.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that the scsi tree has hit mainline we can use the newly added WRITE_SAME_16
define.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The mv_init_host will be used to initialize the host hw on resume.
The PCI bar description need to be initialized only once when the
device probed.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The old value (0xbc) in cycles of the IORDY timeout is suitable for
devices with core clock of 166 MHz, but some SoC controllers have
faster core clocks. The new value will make the IORDY timeout large
enough also for all SoC devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If using 64-bit PTEs and 4K pages then each page table has 512 entries
(as opposed to 1024 entries with 32-bit PTEs). Unlike MIPS, SH follows
the convention that all structures in the page table (pgd_t, pmd_t,
pgprot_t, etc) must be the same size. Therefore, 64-bit PTEs require
64-bit PGD entries, etc. Using 2-levels of page tables and 64-bit PTEs
it is only possible to map 1GB of virtual address space.
In order to map all 4GB of virtual address space we need to adopt a
3-level page table layout. This actually works out better for
CONFIG_SUPERH32 because we only waste 2 PGD entries on the P1 and P2
areas (which are untranslated) instead of 256.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Keep the dimensions of the page tables in a separate header file in
preparation for allowing a three level page table structure.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
MAX_DMA_CHANNELS is tested for the total number of channels in order to
populate an IRQ map. Stub this out completely when no DMA support is
enabled -- as used to be the default behaviour before this was
generalized for use by the dmaengine code.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some models are equipped with an "AVMode" function key that sends
sony-laptop: Unknown event: 0x100 0xa1
sony-laptop: Unknown event: 0x100 0x21
for press and release respectively.
Cc: "Matthew W. S. Bell" <matthew@bells23.org.uk>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
The cardbus code creates PCI devices without ever going through the
necessary fixup bits and pieces that normal PCI devices go through.
There's in fact a commented out call to pcibios_fixup_bus() in there,
it's commented because ... it doesn't work.
I could make pcibios_fixup_bus() do the right thing on powerpc easily
but I felt it cleaner instead to provide a specific hook pci_fixup_cardbus
for which a weak empty implementation is provided by the PCI core.
This fixes cardbus on powerbooks and probably all other PowerPC
platforms which was broken completely for ever on some platforms and
since 2.6.31 on others such as PowerBooks when we made the DMA ops
mandatory (since those are setup by the fixups).
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There's no reason for MIPS to select EMBEDDED. In fact, EMBEDDED makes
MIPS more awkward to deal with because it makes it different to the
majority of architectures for no good reason.
[Ralf: Historically disabling EMBEDDED had hid essential options for many
MIPS platforms such as serial console and forced crap like VGA support
or power managment enabled for platforms where those don't make any sense.
The name of the option is also _very_ missleading so many users don't
select it even where is was required for a functioning kernel.]
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently, MIPS kernels silently overwrite kernel command-line parameters
hardcoded in CONFIG_CMDLINE by the ones received from firmware. Therefore,
using firmware remains the only reliable method to transfer the
command-line parameters, which is not always desirable or convenient, and
the CONFIG_CMDLINE option is thereby effectively rendered useless.
This patch fixes the problem described above and introduces a more flexible
scheme of handling the kernel command line, in a manner identical to what is
currently used for x86. The default behavior, i.e. when CONFIG_CMDLINE_BOOL
is not defined, retains the existing semantics, and firmware command-line
arguments override the hardcoded ones.
[Ralf: I fixed up all the defconfig files so the stay unaffected by this
change.]
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/689/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Yeeloong 2F netbook has an KB3310B embedded controller to manage the LID
action. When the LID is closed or opened a SCI interrupt is sent out and
the corresponding event is saved to an EC register for later query.
Allow the LID open interrupt to wake the processor from wait mode if it is
in the suspend mode.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/685/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several static uninitialized variables are used in the scope of __init
functions but are themselves not marked as __initdata. This patch is to put
those variables to where they belong and to reduce the memory footprint a
little bit.
Also, a couple of lines with spaces instead of tabs were fixed.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/698/
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
That thread "MIPS: Add option to pass return address location to
_mcount" from "David Daney <ddaney@caviumnetworks.com>" have added a new
option -mmcount-ra-address to gcc(4.5) for MIPS to transfer the location
of the return address to _mcount.
Benefit from this new feature, function graph tracer on MIPS will be
easier and safer to hijack the return address of the kernel function,
which will save some overhead and make the whole thing more reliable.
In this patch, at first, try to enable the option -mmcount-ra-address in
arch/mips/Makefile with cc-option, if gcc support it, it will be
enabled, otherwise, no side effect.
and then, we need to support this new option of gcc 4.5 and also support
the old gcc versions.
with _mcount in the old gcc versions, it's not easy to get the location
of return address(tracing: add function graph tracer support for MIPS),
so, we do it in a C function: ftrace_get_parent_addr(ftrace.c), but
with -mmcount-ra-address, only several instructions need to get what
we want, so, I put into asm(mcount.S). and also, as the $12(t0) is
used by -mmcount-ra-address for transferring the localtion of return
address to _mcount, we need to save it into the stack and restore it
when enabled dynamic function tracer, 'Cause we have called
"ftrace_call" before "ftrace_graph_caller", which may destroy
$12(t0).
(Thanks to David for providing that -mcount-ra-address and giving the
idea of KBUILD_MCOUNT_RA_ADDRESS, both of them have made the whole
thing more beautiful!)
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Nicholas Mc Guire <der.herr@hofr.at>
Cc: zhangfx@lemote.com
Cc: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/681/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
