Added the support for Toshiba Satellite M300 with Conexant 5051 codec.
Since the laptop has no port C connection and the pin reports always
the jack sense true, we need to ignore port-C unsol event.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a bad shift in the post div.
Should fix fdo bug 26145
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only reset the reg block on the initial execute
table call; nested calls require the reg block not be
reset on each call. Also reset the fb window and
io mode. This matches the upstream parser behavior.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- split pll adjust into a separate function
- use a union for SetPixelClock params
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- add a new flag for fixed post div
- pull the pll flags into the struct
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
CONFIG_X86_CPU_DEBUG, which provides some parsed versions of the x86
CPU configuration via debugfs, has caused boot failures on real
hardware. The value of this feature has been marginal at best, as all
this information is already available to userspace via generic
interfaces.
Causes crashes that have not been fixed + minimal utility -> remove.
See the referenced LKML thread for more information.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <alpine.LFD.2.00.1001221755320.13231@localhost.localdomain>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Minor fixes for HP Compaq Presario F700 quirks with Cxt5051 codec:
- changed the capture mixer elements to the standard name.
- fixed the quirk name string without a space
- sorted the quirk list
- updated the documentation
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Y2_HW_WOL_ON/Y2_HW_WOL_OFF should be set and cleared per chip,
not per port. On dual port cards, Y2_HW_WOL_ON should be
enabled if either sky2 port has WOL enabled.
Found while reviewing code for a WOL regression, though this is
probably not the cause of the regression.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patch from Sridhar Samudrala
The following patch fixes the check for IPv6 GSO packet in ixgbevf
driver to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
CC: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter whether connection track is enabled, an end host should send
an ICMPv4 "Fragment Reassembly Timeout" message when defrag timeout.
The reasons are following two points:
1. RFC 792 says:
>>>> >> > > If a host reassembling a fragmented datagram cannot complete the
>>>> >> > > reassembly due to missing fragments within its time limit it
>>>> >> > > discards the datagram, and it may send a time exceeded message.
>>>> >> > >
>>>> >> > > If fragment zero is not available then no time exceeded need be
>>>> >> > > sent at all.
>>>> >> > >
>>>> >> > > Read more: http://www.faqs.org/rfcs/rfc792.html#ixzz0aOXRD7Wp
2. Patrick McHardy also agrees with this opinion. :-)
About the discussion of this opinion, refer to http://patchwork.ozlabs.org/patch/41649
The patch fixed the problem like this:
When enabling connection track, fragments are received at PRE_ROUTING HOOK.
If they are failed to reassemble, ip_expire() will be called.
Before sending an ICMP "Fragment Reassembly Timeout" message,
the patch searches router table to get the destination entry only for host type.
The patch has been tested on both host type and route type.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct. The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simpily pass 'struct neigh_table' with seq_file private pointer,
and save one dereference. Proc entry itself isn't interesting.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After netdev_ops compat code HAVE_* macros aren't needed, in fact
they _will_ result in compile breakage for out of tree drivers.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add igbvf to the list of supported Intel drivers and Alex to the list of
maintainers.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF driver gets a control message from the PF that indicates the
PF is about to reset or go down we schedule the watchdog timer so that
it will detect the PF has gone offline and take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inadequate coordination between the PF driver and the VF driver results
in tx hangs in the VF driver when you perform certain actions that will
lead to a re-init of the PF. Add feature to notify active VFs when the PF
is about to re-initialize so that the VFs can take appropriate action.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF Reset Done bit should not be set in the extended control register
until the PF has actually completed the bring up process. It is a mis-
interpretation of the purpose of this bit to assume it should be set
when the physical reset of the device is done. Instead it should be used
to indicate to the VFs when the PF is ready to provide them with required
services. This is not until after the PF is finished coming up and ready
to process mailbox events.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are allocated (as indicated by adapter->num_vfs is non-zero) then
the PF pool is no longer zero. Instead it will be the same as the number
of VFs allocated. When setting the VLVF entry for the PF we need to use
the correct pool otherwise the PF will get VLAN packets from the wire
because the packet will pass VFTA filtering and the PF has the default
pool, but it will not get VLAN packets from the VFs because it has
not set the correct pool bit in the VLVF entry.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing the "e1000: enhance frame fragment detection" (and e1000e)
patches we found some bugs with reducing the MTU size. The 1024 byte
descriptor used with the 1000 mtu test also (re) introduced the
(originally) reported bug, and causes us to need the e1000_clean_tx_irq
"enhance frame fragment detection" fix.
So what has occured here is that 2.6.32 is only vulnerable for mtu <
1500 due to the jumbo specific routines in both e1000 and e1000e.
So, 2.6.32 needs the 2kB buffer len fix for those smaller MTUs, but
is not vulnerable to the original issue reported. It has been pointed
out that this vulnerability needs to be patched in older kernels that
don't have the e1000 jumbo routine. Without the jumbo routines, we
need the "enhance frame fragment detection" fix the e1000, old
e1000e is only vulnerable for < 1500 mtu, and needs a similar
fix. We split the patches up to provide easy backport paths.
There is only a slight bit of extra code when this fix and the
original "enhance frame fragment detection" fixes are applied, so
please apply both, even though it is a bit of overkill.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fmvj18x_cs, serial_cs:
add new id
Panasonic lan & modem card (model name:AL-VML101)
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first two fields of mcc wrb - embedded, payload_len
need to be cpu_to_le32() swapped while issuing a cmd to the hw.
The fields tag0, tag1 are opaque and returned back to cpu as is...
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please add support for Microsoft MN-120 PCMCIA network card. It's an
old card, I know, but adding support is very easy. You just need to
get tulip_core.c to recognise its vendor/device ID.
Patch for kernel 2.6.32.4 (and many previous) attached.
.....Ron Murray
Signed-off-by: Ron Murray <rjmx@rjmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
nodes_possible_map does not currently include nodes that have SRAT
entries that are all ACPI_SRAT_MEM_HOT_PLUGGABLE since the bit is
cleared in nodes_parsed if it does not have an online address range.
Unequivocally setting the bit in nodes_parsed is insufficient since
existing code, such as acpi_get_nodes(), assumes all nodes in the map
have online address ranges. In fact, all code using nodes_parsed
assumes such nodes represent an address range of online memory.
nodes_possible_map is created by unioning nodes_parsed and
cpu_nodes_parsed; the former represents nodes with online memory and
the latter represents memoryless nodes. We now set the bit for
hotpluggable nodes in cpu_nodes_parsed so that it also gets set in
nodes_possible_map.
[ hpa: Haicheng Li points out that this makes the naming of the
variable cpu_nodes_parsed somewhat counterintuitive. However, leave
it as is in the interest of keeping the pure bug fix patch small. ]
Signed-off-by: David Rientjes <rientjes@google.com>
Tested-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <alpine.DEB.2.00.1001201152040.30528@chino.kir.corp.google.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need to know the valid L3 indices interval when disabling them over
/sysfs. Do that when the core is brought online and add boundary checks
to the sysfs .store attribute.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-6-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The cache_disable_[01] attribute in
/sys/devices/system/cpu/cpu?/cache/index[0-3]/
is enabled on all cache levels although only L3 supports it. Add it only
to the cache level that actually supports it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-5-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* Correct the masks used for writing the cache index disable indices.
* Do not turn off L3 scrubber - it is not necessary.
* Make sure wbinvd is executed on the same node where the L3 is.
* Check for out-of-bounds values written to the registers.
* Make show_cache_disable hex values unambiguous
* Check for Erratum #388
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-4-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add wbinvd_on_cpu and wbinvd_on_all_cpus stubs for executing wbinvd on a
particular CPU.
[ hpa: renamed lib/smp.c to lib/cache-smp.c ]
[ hpa: wbinvd_on_all_cpus() returns int, but wbinvd() returns
void. Thus, the former cannot be a macro for the latter,
replace with an inline function. ]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-2-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
ieee80211_tx_h_select_key might decide that a frame
need not be encrypted at all, in which case it will
clear tx->key. In that case it may crash if a key
was previously selected, e.g. as the default key.
This is also due to my patch
"mac80211: move control.hw_key assignment".
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pass "struct clusterip_config" itself to seq_file iterators
and save one dereference. Proc entry itself isn't interesting.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch continues the effort which began with:
"[PATCH] p54pci: move tx cleanup into tasklet".
Thanks to these changes, p54pci's interrupt & tx
cleanup routines can be made lock-less.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
