Allow bpf to set a filter to drop packets that dont
match a specific mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
The i2400m driver uses two different bits to distinguish how much the
driver is up. i2400m->ready is used to denote that the infrastructure
to communicate with the device is up and running. i2400m->updown is
used to indicate if 'ready' and the device is up and running, ready to
take control and data traffic.
However, all this was pretty dirty and not clear, with many open spots
where race conditions were present.
This commit cleans up the situation by:
- documenting the usage of both bits
- setting them only in specific, well controlled places
(i2400m_dev_start, i2400m_dev_stop)
- ensuring the i2400m workqueue can't get in the middle of the
setting by flushing it when i2400m->ready is set to zero. This
allows the report hook not having to check again for the bit to be
set [rx.c:i2400m_report_hook_work()].
- using i2400m->updown to determine if the device is up and running
instead of the wimax state in i2400m_dev_reset_handle().
- not loosing missed messages sent by the hardware before
i2400m->ready is set. In rx.c, whatever the device sends can be
sent to user space over the message pipes as soon as the wimax
device is registered, so don't wait for i2400m->ready to be set.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Add support for the WiMAX device in the Intel WiFi/WiMAX Link 6050
Series; this involves:
- adding the device ID to bind to and an endpoint mapping for the
driver to use.
- at probe() time, some things are set depending on the device id:
+ the list of firmware names to try
+ mapping of endpoints
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Different sdio device IDs are designated to support different intel
wimax silicon sku. The new macro SDIO_DEVICE_ID_IWMC3200_WIMAX_2G5(0x1407)
is added to support iwmc3200 2.5GHz sku. The existing
SDIO_DEVICE_ID_IWMC3200_WIMAX(0x1402) is for iwmc3200 general sku.
Signed-off-by: Cindy H Kao <cindy.h.kao@intel.com>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m based devices can get in a sort of a deadlock some times;
when they boot, they send a reboot "barker" (a magic number) and then
the driver has to echo that same barker to ack reception
(echo/ack). Then the device does a final ack by sending an ACK barker.
The first time this happens, we don't know ahead of time with barker
the device is going to send, as different device models and SKUs will
send different barker depending on the EEPROM programming.
If the device has sent the barker before the driver has been able to
read it, the driver looses, as it doesn't know which barker it has to
echo/ack back. With older devices, we tried a couple of combinations
and that always worked; but now, with adding support for more, in
which we have an unlimited number of new barkers, that is not an
option.
So we rework said case so that when the device gets stuck, we just
cycle through all the known types until one forces the device to send
an ack. Otherwise, the driver gives up and aborts.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The i2400m based devices can boot two main types of firmware images:
signed and non-signed. Signed images have signature data included that
must match that of a certificate stored in the device.
Currently the code is making the decission on what type of firmware
load (signed vs non-signed) is going to be loaded based on a hardcoded
decission in __i2400m_ack_verify(), based on the barker the device
sent upon boot.
This is not flexible enough as future hardware will emit more barkers;
thus the bit has to be set in a place where there is better knowledge
of what is going on. This will be done in follow-up commits -- however
this patch paves the way for it.
So the querying of the mode is packed into i2400m_boot_is_signed();
the main changes are just using i2400m_boot_is_signed() to determine
the method to follow and setting i2400m->sboot in
i2400m_is_boot_barker(). The modifications in i2400m_dnload_init() and
i2400m_dnload_finalize() are just reorganizing the order of the if
blocks and thus look larger than they really are.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Add "debug" module options to all the wimax modules (including
drivers) so that the debug levels can be set upon kernel boot or
module load time.
This is needed as currently there was a limitation where the debug
levels could only be set when a device was succesfully
enumerated. This made it difficult to debug issues that made a device
not probe properly.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
The last users of skb_icv_walk are converted to ahash now,
so skb_icv_walk is unused and can be removed.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ah4 and ah6 are converted to ahash now, so we can remove the
code for the obsolete hash algorithm.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support for ahash algorithms, we add a pointer to a
crypto_ahash to ah_data.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused digest_alg and hash_alg structs from crypto_alg union and
kill their definitions. This also ensures that old-style digest/hash
algorithms maintained out of tree will break at build time rather than
oopsing at runtime.
Signed-off-by: Benjamin Gilbert <bgilbert@cs.cmu.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
6941c3a0 disabled compilation of the legacy digest code but didn't
actually remove it. Rectify this. Also, remove the crypto_hash_type
extern declaration from algapi.h now that the struct is gone.
Signed-off-by: Benjamin Gilbert <bgilbert@cs.cmu.edu>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
PCLMULQDQ is used to accelerate the most time-consuming part of GHASH,
carry-less multiplication. More information about PCLMULQDQ can be
found at:
http://software.intel.com/en-us/articles/carry-less-multiplication-and-its-usage-for-computing-the-gcm-mode/
Because PCLMULQDQ changes XMM state, its usage must be enclosed with
kernel_fpu_begin/end, which can be used only in process context, the
acceleration is implemented as crypto_ahash. That is, request in soft
IRQ context will be defered to the cryptd kernel thread.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In order to have better cache layouts of struct sock (separate zones
for rx/tx paths), we need this preliminary patch.
Goal is to transfert fields used at lookup time in the first
read-mostly cache line (inside struct sock_common) and move sk_refcnt
to a separate cache line (only written by rx path)
This patch adds inet_ prefix to daddr, rcv_saddr, dport, num, saddr,
sport and id fields. This allows a future patch to define these
fields as macros, like sk_refcnt, without name clashes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optional open and close methods for preparing and closing
the device.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Conflicts:
kernel/Makefile
kernel/trace/Makefile
kernel/trace/trace.h
samples/Makefile
Merge reason: We need to be uptodate with the perf events development
branch because we plan to rewrite the breakpoints API on top of
perf events.
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
sata_mv: Prevent PIO commands to be defered too long if traffic in progress.
pata_sc1200: Fix crash on boot
libata: fix internal command failure handling
libata: fix PMP initialization
sata_nv: make sure link is brough up online when skipping hardreset
ahci / atiixp / pci quirks: rename AMD SB900 into Hudson-2
ahci: Add the AHCI controller Linux Device ID for NVIDIA chipsets.
pata_via: extend the rev_max for VT6330
Merge common code between Sparc, PowerPC and Microblaze.
Sparc differs in the implementation at this point, so this patch uses
a #ifdef to handle sparc differently for now. The merging of
implementations will occur in a later patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Driver for Texas Instruments TLV320DAC33 (SLAS546) low power stereo
audio DAC.
TLV320DAC33 is a stereo audio codec with integrated 24KB FIFO for low
power audio playback.
The digital interface can use I2S, DSP (A or B), Right and Left
justified formats.
DAC33 has stereo analog input, which can be bypassed to the analog
outputs.
Regarding to the internal 24KB FIFO the driver implements 'FIFO bypass'
mode (default) and nSample mode (FIFO is in use).
a) In 'FIFO bypass' mode the internal FIFO is not in use, the codec is
working synchronously as a normal codec (it needs constant stream of
data on the digital interface).
b) The nSample mode implementation uses one interrupt line from DAC33 to
the host:
Alarm threshold is set to 10ms of audio data (limit by the driver
implementation).
DAC33 will signal an interrupt, when the FIFO level goes under the
Alarm threshold.
The host will write to nSample register a value (number of stereo
samples), to tell DAC33 how many samples it should read in a burst from
the host. When the DAC33 received the number of samples, it disables the
clocks on the I2S bus. When the FIFO use again goes under the Alarm
threshold, DAC33 signals the host with an interrupt, and the process is
repeated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PM core will grow pm_link infrastructure in 2.6.33 which can be
used to implement the intended functionality of the ASoC-specific
device suspend and resume callbacks so drop them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we can filter based on fields via perf record, people
will start using filter expressions and will expect them to
be obvious.
The primary way to see which fields are available is by looking
at the trace output, such as:
gcc-18676 [000] 343.011728: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.012727: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.032692: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.033690: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.034687: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.035686: irq_handler_entry: irq=0 handler=timer
cc1-18677 [000] 343.036684: irq_handler_entry: irq=0 handler=timer
While 'irq==0' filters work, the 'handler==<x>' filter expression
does not work:
$ perf record -R -f -a -e irq:irq_handler_entry --filter handler=timer sleep 1
Error: failed to set filter with 22 (Invalid argument)
The problem is that while an 'irq' field exists and is recognized
as a filter field - 'handler' does not exist - its name is 'name'
in the output.
To solve this, we need to synchronize the printout and the field
names, wherever possible.
In cases where the printout prints a non-field, we enclose
that information in square brackets, such as:
perf-1380 [013] 724.903505: softirq_exit: vec=9 [action=RCU]
perf-1380 [013] 724.904482: softirq_exit: vec=1 [action=TIMER]
This way users can use filter expressions more intuitively: all
fields that show up as 'primary' (non-bracketed) information is
filterable.
This patch harmonizes the field names for all irq, bkl, power,
sched and timer events.
We might in fact think about dropping the print format bit of
generic tracepoints altogether, and just print the fields that
are being recorded.
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Merge reason: to add event filter support we need the following
commits from the tracing tree:
3f6fe06: tracing/filters: Unify the regex parsing helpers
1889d20: tracing/filters: Provide basic regex support
737f453: tracing/filters: Cleanup useless headers
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Phonet "universe" only has 64 addresses, so we keep a trivial flat
routing table.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Topology Map of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC,
and when a read request to the Topology Map arrived it had to be
converted to big endian byte order again.
We now generate it in big endian byte order in the first place.
This also rids us of 1000 bytes stack usage in tasklet context.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The config ROM image of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC, and
finally the card driver created its own big endian copy.
We now generate it in big endian byte order in the first place to avoid
one byte order conversion and the temporary on-stack copy of the ROM
image (1000 bytes stack usage in process context). Furthermore, two
1000 bytes memset()s are replaced by one 1000 bytes - ROM length sized
memset.
The trivial fw_memcpy_{from,to}_be32() helpers are now superfluous and
removed. The newly added __compute_block_crc() function will be folded
into fw_compute_block_crc() in a subsequent change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Yanmin reported that both tbench and hackbench were significantly
hurt by trying to keep tasks local on these domains, esp on small
cache machines.
So disable it in order to promote spreading outside of the cache
domains.
Reported-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
CC: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1255083400.8802.15.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Most of the syscalls metadata processing is done from arch.
But these operations are mostly generic accross archs. Especially now
that we have a common variable name that expresses the number of
syscalls supported by an arch: NR_syscalls, the only remaining bits
that need to reside in arch is the syscall nr to addr translation.
v2: Compare syscalls symbols only after the "sys" prefix so that we
avoid spurious mismatches with archs that have syscalls wrappers,
in which case syscalls symbols have "SyS" prefixed aliases.
(Reported by: Heiko Carstens)
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
Cc: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Extend the driver to accept a MAC address specified in platform_data.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
