Pull ARM SoC fixes from Arnd Bergmann:
"There is a fairly large number of bug fixes for Qualcomm platforms,
most of them addressing issues with the devicetree files for the newly
added Snapdragon X1 based laptops to make them more reliable.
The Qualcomm driver changes address a few build-time issues as well as
runtime problems in the tzmem and scm firmware, the USB Type-C driver,
and the cmd-db and pmic_glink soc drivers.
The NXP i.MX usually gets a bunch of devicetree fixes that is
proportional to the number of supported machines. This includes both
warning fixes and correctness for the 64-bit i.MX9, i.MX8 and
layerscape platforms, as well as a single fix for a 32-bit i.MX6 based
board.
The other changes are the usual minor changes, including an update to
the MAINTAINERS file, an omap3 dts file and a SoC driver for mpfs
(risc-v)"
* tag 'arm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (50 commits)
firmware: microchip: fix incorrect error report of programming:timeout on success
soc: qcom: pd-mapper: Fix singleton refcount
firmware: qcom: tzmem: disable sdm670 platform
soc: qcom: pmic_glink: Actually communicate when remote goes down
usb: typec: ucsi: Move unregister out of atomic section
soc: qcom: pmic_glink: Fix race during initialization
firmware: qcom: qseecom: remove unused functions
firmware: qcom: tzmem: fix virtual-to-physical address conversion
firmware: qcom: scm: Mark get_wq_ctx() as atomic call
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
...
Qualcomm Arm64 DeviceTree fixes for v6.11
On X1E the GPU node is disabled by default, to be enabled in the
individual devices once the developers install the required firmware.
The generic EDP panel driver used on the X1E CRD is replaced with the
Samsung ATNA45AF01 driver, in order to ensure backlight is brought back
up after being turned off.
The pin configuration for PCIe-related pins are corrected across all the
X1E targets. The PCIe controllers gain a minimum OPP vote, and PCIe
domain numbers are corrected.
WiFi calibration variant information is added to the Lenovo Yoga Slim
7x, to pick the right data from the firmware packages.
The incorrect Adreno SMMU global interrupt is corrected.
For IPQ5332, the IRQ triggers for the USB controller are corrected.
* tag 'qcom-arm64-fixes-for-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (23 commits)
arm64: dts: qcom: x1e80100: Fix Adreno SMMU global interrupt
arm64: dts: qcom: disable GPU on x1e80100 by default
arm64: dts: qcom: x1e80100-crd: Fix backlight
arm64: dts: qcom: x1e80100-yoga-slim7x: fix missing PCIe4 gpios
arm64: dts: qcom: x1e80100-yoga-slim7x: disable PCIe6a perst pull down
arm64: dts: qcom: x1e80100-yoga-slim7x: fix up PCIe6a pinctrl node
arm64: dts: qcom: x1e80100-yoga-slim7x: fix PCIe4 PHY supply
arm64: dts: qcom: x1e80100-vivobook-s15: fix missing PCIe4 gpios
arm64: dts: qcom: x1e80100-vivobook-s15: disable PCIe6a perst pull down
arm64: dts: qcom: x1e80100-vivobook-s15: fix up PCIe6a pinctrl node
arm64: dts: qcom: x1e80100-vivobook-s15: fix PCIe4 PHY supply
arm64: dts: qcom: x1e80100-qcp: fix missing PCIe4 gpios
arm64: dts: qcom: x1e80100-qcp: disable PCIe6a perst pull down
arm64: dts: qcom: x1e80100-qcp: fix up PCIe6a pinctrl node
arm64: dts: qcom: x1e80100-qcp: fix PCIe4 PHY supply
arm64: dts: qcom: x1e80100-crd: fix missing PCIe4 gpios
arm64: dts: qcom: x1e80100-crd: disable PCIe6a perst pull down
arm64: dts: qcom: x1e80100-crd: fix up PCIe6a pinctrl node
arm64: dts: qcom: x1e80100: add missing PCIe minimum OPP
arm64: dts: qcom: x1e80100: fix PCIe domain numbers
...
Link: https://lore.kernel.org/r/20240826152426.1648383-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX fixes for 6.11:
- One imx8mp-beacon-kit change from Adam Ford to fix the broken WM8962
audio support
- One pinctrl property typo fix for imx8mm-phygate
- One layerscape fix from Krzysztof Kozlowski to get thermal nodes
correct name length
- A couple of imx93-tqma9352 fixes from Markus Niebel, one on CMA
alloc-ranges and the other on SD-Card cd-gpios typo
- One change from Michal Vokáč to fix imx6dl-yapp43 LED current to match
the HW design
- A couple of imx95 fixes from Peng Fan, one to correct a55 power
domains and the other to correct L3Cache cache-sets
- One tqma9352 watchdog reset fix from Sascha Hauer
- One imx93 change from Shenwei Wang to fix the default value for STMMAC
EQOS snps,clk-csr
* tag 'imx-fixes-6.11' of https://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8mm-phygate: fix typo pinctrcl-0
arm64: dts: imx95: correct L3Cache cache-sets
arm64: dts: imx95: correct a55 power-domains
arm64: dts: freescale: imx93-tqma9352-mba93xxla: fix typo
arm64: dts: freescale: imx93-tqma9352: fix CMA alloc-ranges
ARM: dts: imx6dl-yapp43: Increase LED current to match the yapp4 HW design
arm64: dts: imx93: update default value for snps,clk-csr
arm64: dts: freescale: tqma9352: Fix watchdog reset
arm64: dts: imx8mp-beacon-kit: Fix Stereo Audio on WM8962
arm64: dts: layerscape: fix thermal node names length
Link: https://lore.kernel.org/r/ZrtsTO1+jXhJ6GSM@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull arm64 kvm fixes from Catalin Marinas:
- Don't drop references on LPIs that weren't visited by the vgic-debug
iterator
- Cure lock ordering issue when unregistering vgic redistributors
- Fix for misaligned stage-2 mappings when VMs are backed by hugetlb
pages
- Treat SGI registers as UNDEFINED if a VM hasn't been configured for
GICv3
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
KVM: arm64: Ensure canonical IPA is hugepage-aligned when handling fault
KVM: arm64: vgic: Don't hold config_lock while unregistering redistributors
KVM: arm64: vgic-debug: Don't put unmarked LPIs
KVM/arm64 fixes for 6.11, round #2
- Don't drop references on LPIs that weren't visited by the
vgic-debug iterator
- Cure lock ordering issue when unregistering vgic redistributors
- Fix for misaligned stage-2 mappings when VMs are backed by hugetlb
pages
- Treat SGI registers as UNDEFINED if a VM hasn't been configured for
GICv3
* tag 'kvmarm-fixes-6.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm:
KVM: arm64: Make ICC_*SGI*_EL1 undef in the absence of a vGICv3
KVM: arm64: Ensure canonical IPA is hugepage-aligned when handling fault
KVM: arm64: vgic: Don't hold config_lock while unregistering redistributors
KVM: arm64: vgic-debug: Don't put unmarked LPIs
KVM: arm64: vgic: Hold config_lock while tearing down a CPU interface
KVM: selftests: arm64: Correct feature test for S1PIE in get-reg-list
KVM: arm64: Tidying up PAuth code in KVM
KVM: arm64: vgic-debug: Exit the iterator properly w/o LPI
KVM: arm64: Enforce dependency on an ARMv8.4-aware toolchain
docs: KVM: Fix register ID of SPSR_FIQ
KVM: arm64: vgic: fix unexpected unlock sparse warnings
KVM: arm64: fix kdoc warnings in W=1 builds
KVM: arm64: fix override-init warnings in W=1 builds
KVM: arm64: free kvm->arch.nested_mmus with kvfree()
On a system with a GICv3, if a guest hasn't been configured with
GICv3 and that the host is not capable of GICv2 emulation,
a write to any of the ICC_*SGI*_EL1 registers is trapped to EL2.
We therefore try to emulate the SGI access, only to hit a NULL
pointer as no private interrupt is allocated (no GIC, remember?).
The obvious fix is to give the guest what it deserves, in the
shape of a UNDEF exception.
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20240820100349.3544850-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Zenghui reports that VMs backed by hugetlb pages are no longer booting
after commit fd276e71d1 ("KVM: arm64: nv: Handle shadow stage 2 page
faults").
Support for shadow stage-2 MMUs introduced the concept of a fault IPA
and canonical IPA to stage-2 fault handling. These are identical in the
non-nested case, as the hardware stage-2 context is always that of the
canonical IPA space.
Both addresses need to be hugepage-aligned when preparing to install a
hugepage mapping to ensure that KVM uses the correct GFN->PFN translation
and installs that at the correct IPA for the current stage-2.
And now I'm feeling thirsty after all this talk of IPAs...
Fixes: fd276e71d1 ("KVM: arm64: nv: Handle shadow stage 2 page faults")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240822071710.2291690-1-oliver.upton@linux.dev
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
We recently moved the teardown of the vgic part of a vcpu inside
a critical section guarded by the config_lock. This teardown phase
involves calling into kvm_io_bus_unregister_dev(), which takes the
kvm->srcu lock.
However, this violates the established order where kvm->srcu is
taken on a memory fault (such as an MMIO access), possibly
followed by taking the config_lock if the GIC emulation requires
mutual exclusion from the other vcpus.
It therefore results in a bad lockdep splat, as reported by Zenghui.
Fix this by moving the call to kvm_io_bus_unregister_dev() outside
of the config_lock critical section. At this stage, there shouln't
be any need to hold the config_lock.
As an additional bonus, document the ordering between kvm->slots_lock,
kvm->srcu and kvm->arch.config_lock so that I cannot pretend I didn't
know about those anymore.
Fixes: 9eb18136af ("KVM: arm64: vgic: Hold config_lock while tearing down a CPU interface")
Reported-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Tested-by: Zenghui Yu <yuzenghui@huawei.com>
Link: https://lore.kernel.org/r/20240819125045.3474845-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Pull arm64 fixes from Catalin Marinas:
- Fix the arm64 __get_mem_asm() to use the _ASM_EXTABLE_##type##ACCESS()
macro instead of the *_ERR() one in order to avoid writing -EFAULT to
the value register in case of a fault
- Initialise all elements of the acpi_early_node_map[] to NUMA_NO_NODE.
Prior to this fix, only the first element was initialised
- Move the KASAN random tag seed initialisation after the per-CPU areas
have been initialised (prng_state is __percpu)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: Fix KASAN random tag seed initialization
arm64: ACPI: NUMA: initialize all values of acpi_early_node_map to NUMA_NO_NODE
arm64: uaccess: correct thinko in __get_mem_asm()
Currently, kasan_init_sw_tags() is called before setup_per_cpu_areas(),
so per_cpu(prng_state, cpu) accesses the same address regardless of the
value of "cpu", and the same seed value gets copied to the percpu area
for every CPU. Fix this by moving the call to smp_prepare_boot_cpu(),
which is the first architecture hook after setup_per_cpu_areas().
Fixes: 3c9e3aa110 ("kasan: add tag related helper functions")
Fixes: 3f41b60938 ("kasan: fix random seed generation for tag-based mode")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Link: https://lore.kernel.org/r/20240814091005.969756-1-samuel.holland@sifive.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The GPU on X1E80100 requires ZAP 'shader' file to be useful. Since the
file is signed by the OEM keys and might be not available by default,
disable the GPU node and drop the firmware name from the x1e80100.dtsi
file. Devices not being fused to use OEM keys can specify generic
location at `qcom/x1e80100/gen70500_zap.mbn` while enabling the GPU.
The CRD and QCP were lucky enough to work with the default settings, so
reenable the GPU on those platforms and provide correct firmware-name
(including the SoC subdir).
Fixes: 721e38301b ("arm64: dts: qcom: x1e80100: Add gpu support")
Cc: Akhil P Oommen <quic_akhilpo@quicinc.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Caleb Connolly <caleb.connolly@linaro.org>
Reviewed-by: Akhil P Oommen <quic_akhilpo@quicinc.com>
Link: https://lore.kernel.org/r/20240715-x1e8-zap-name-v3-1-e7a5258c3c2e@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
In the CONFIG_CC_HAS_ASM_GOTO_OUTPUT=y version of __get_mem_asm(), we
incorrectly use _ASM_EXTABLE_##type##ACCESS_ERR() such that upon a fault
the extable fixup handler writes -EFAULT into "%w0", which is the
register containing 'x' (the result of the load).
This was a thinko in commit:
86a6a68feb ("arm64: start using 'asm goto' for get_user() when available")
Prior to that commit _ASM_EXTABLE_##type##ACCESS_ERR_ZERO() was used
such that the extable fixup handler wrote -EFAULT into "%w0" (the
register containing 'err'), and zero into "%w1" (the register containing
'x'). When the 'err' variable was removed, the extable entry was updated
incorrectly.
Writing -EFAULT to the value register is unnecessary but benign:
* We never want -EFAULT in the value register, and previously this would
have been zeroed in the extable fixup handler.
* In __get_user_error() the value is overwritten with zero explicitly in
the error path.
* The asm goto outputs cannot be used when the goto label is taken, as
older compilers (e.g. clang < 16.0.0) do not guarantee that asm goto
outputs are usable in this path and may use a stale value rather than
the value in an output register. Consequently, zeroing in the extable
fixup handler is insufficient to ensure callers see zero in the error
path.
* The expected usage of unsafe_get_user() and get_kernel_nofault()
requires that the value is not consumed in the error path.
Some versions of GCC would mis-compile asm goto with outputs, and
erroneously omit subsequent assignments, breaking the error path
handling in __get_user_error(). This was discussed at:
https://lore.kernel.org/lkml/ZpfxLrJAOF2YNqCk@J2N7QTR9R3.cambridge.arm.com/
... and was fixed by removing support for asm goto with outputs on those
broken compilers in commit:
f2f6a8e887 ("init/Kconfig: remove CONFIG_GCC_ASM_GOTO_OUTPUT_WORKAROUND")
With that out of the way, we can safely replace the usage of
_ASM_EXTABLE_##type##ACCESS_ERR() with _ASM_EXTABLE_##type##ACCESS(),
leaving the value register unchanged in the case a fault is taken, as
was originally intended. This matches other architectures and matches
our __put_mem_asm().
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20240807103731.2498893-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
KVM/arm64 fixes for 6.11, round #1
- Use kvfree() for the kvmalloc'd nested MMUs array
- Set of fixes to address warnings in W=1 builds
- Make KVM depend on assembler support for ARMv8.4
- Fix for vgic-debug interface for VMs without LPIs
- Actually check ID_AA64MMFR3_EL1.S1PIE in get-reg-list selftest
- Minor code / comment cleanups for configuring PAuth traps
- Take kvm->arch.config_lock to prevent destruction / initialization
race for a vCPU's CPUIF which may lead to a UAF
Fix typo pinctrcl-0 with pinctrl-0.
Fix below warning:
arch/arm64/boot/dts/freescale/imx8mm-phygate-tauri-l-rs232-rs485.dtb: gpio@30220000: 'pinctrl-0' is a dependency of 'pinctrl-names'
from schema $id: http://devicetree.org/schemas/pinctrl/pinctrl-consumer.yaml#
arch/arm64/boot/dts/freescale/imx8mm-phygate-tauri-l-rs232-rs485.dtb: uart4_rs485_en: $nodename:0: 'uart4_rs485_en' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$
Fixes: 8d97083c0b ("arm64: dts: phygate-tauri-l: add overlays for RS232 and RS485")
Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The L3Cache size is 512KB.
Size = Cache Line Size(64) * num sets(512) * Assoc(0x10).
Correct the number of Cache sets.
Fixes: 5e3cbb8e42 ("arm64: dts: freescale: add i.MX95 basic dtsi")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A55 power domains is for SCMI performance usage, so for device power
on/off. Correct the power-domains entry to use scmi_perf not scmi_devpd.
Fixes: 5e3cbb8e42 ("arm64: dts: freescale: add i.MX95 basic dtsi")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the tqma9352 the board is reset through an external PMIC, so
set the fsl,ext-reset-output property to enable triggering the
output pin on a watchdog trigger.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The L/R clock needs to be controlled by the SAI3 instead of the
CODEC to properly achieve stereo sound. Doing this allows removes
the need for unnecessary clock manipulation to try to get the
CODEC's clock in sync with the SAI3 clock, since the CODEC can cope
with a wide variety of clock inputs.
Fixes: 161af16c18 ("arm64: dts: imx8mp-beacon-kit: Fix audio_pll2 clock")
Fixes: 69e2f37a6d ("arm64: dts: imx8mp-beacon-kit: Enable WM8962 Audio CODEC")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull ARM SoC fixes from Arnd Bergmann:
"There are three sets of patches for the soc tree:
- Marek Behún addresses multiple build time regressions caused by
changes to the cznic turris-omnia support
- Dmitry Torokhov fixes a regression in the legacy "gumstix" board
code he cleaned up earlier
- The TI K3 maintainers found multiple bugs in the in gpio, audio and
pcie devicetree nodes"
* tag 'arm-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: pxa/gumstix: fix attaching properties to vbus gpio device
doc: platform: cznic: turris-omnia-mcu: Use double backticks for attribute value
doc: platform: cznic: turris-omnia-mcu: Fix sphinx-build warning
platform: cznic: turris-omnia-mcu: Make GPIO code optional
platform: cznic: turris-omnia-mcu: Make poweroff and wakeup code optional
platform: cznic: turris-omnia-mcu: Make TRNG code optional
platform: cznic: turris-omnia-mcu: Make watchdog code optional
arm64: dts: ti: k3-j784s4-main: Correct McASP DMAs
arm64: dts: ti: k3-j722s: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Fix gpio-range for main_pmx0
arm64: dts: ti: k3-am62p: Add gpio-ranges for mcu_gpio0
arm64: dts: ti: k3-am62-verdin-dahlia: Keep CTRL_SLEEP_MOCI# regulator on
arm64: dts: ti: k3-j784s4-evm: Consolidate serdes0 references
arm64: dts: ti: k3-j784s4-evm: Assign only lanes 0 and 1 to PCIe1
Tearing down a vcpu CPU interface involves freeing the private interrupt
array. If we don't hold the lock, we may race against another thread
trying to configure it. Yeah, fuzzers do wonderful things...
Taking the lock early solves this particular problem.
Fixes: 03b3d00a70 ("KVM: arm64: vgic: Allocate private interrupts on demand")
Reported-by: Alexander Potapenko <glider@google.com>
Tested-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240808091546.3262111-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
In case the guest doesn't have any LPI, we previously relied on the
iterator setting
'intid = nr_spis + VGIC_NR_PRIVATE_IRQS' && 'lpi_idx = 1'
to exit the iterator. But it was broken with commit 85d3ccc8b7 ("KVM:
arm64: vgic-debug: Use an xarray mark for debug iterator") -- the intid
remains at 'nr_spis + VGIC_NR_PRIVATE_IRQS - 1', and we end up endlessly
printing the last SPI's state.
Consider that it's meaningless to search the LPI xarray and populate
lpi_idx when there is no LPI, let's just skip the process for that case.
The result is that
* If there's no LPI, we focus on the intid and exit the iterator when it
runs out of the valid SPI range.
* Otherwise we keep the current logic and let the xarray drive the
iterator.
Fixes: 85d3ccc8b7 ("KVM: arm64: vgic-debug: Use an xarray mark for debug iterator")
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240807052024.2084-1-yuzenghui@huawei.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
With the NV support of TLBI-range operations, KVM makes use of
instructions that are only supported by binutils versions >= 2.30.
This breaks the build for very old toolchains.
Make KVM support conditional on having ARMv8.4 support in the
assembler, side-stepping the issue.
Fixes: 5d476ca57d ("KVM: arm64: nv: Add handling of range-based TLBI operations")
Reported-by: Viresh Kumar <viresh.kumar@linaro.org>
Suggested-by: Arnd Bergmann <arnd@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240807115144.3237260-1-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Commit 5e5c50964e ("arm64: dts: ti: k3-j722s: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed a hole within gpio-range for main_pmx0. As a result, automatic
mapping of GPIO to pin control for gpios within the main_pmx0 domain is
broken. Fix this by correcting the gpio-range.
Fixes: 5e5c50964e ("arm64: dts: ti: k3-j722s: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-4-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed a hole within gpio-range for main_pmx0. As a result, automatic
mapping of GPIO to pin control for gpios within the main_pmx0 domain is
broken. Fix this by correcting the gpio-range.
Fixes: d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-3-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Commit d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges
properties") introduced pinmux range definition for gpio-ranges, however
missed introducing the range description for the mcu_gpio node. As a
result, automatic mapping of GPIO to pin control for mcu gpios is
broken. Fix this by introducing the proper ranges.
Fixes: d72d73a44c ("arm64: dts: ti: k3-am62p: Add gpio-ranges properties")
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Link: https://lore.kernel.org/r/20240801210414.715306-2-j-mcarthur@ti.com
Signed-off-by: Nishanth Menon <nm@ti.com>
Linux kernel expects thermal zone node names to be maximum of 19
characters (see THERMAL_NAME_LENGTH, including terminating NUL byte) and
bindings/dtbs_check points that:
fsl-ls2088a-rdb.dtb: thermal-zones: 'core-cluster1-thermal', 'core-cluster2-thermal', 'core-cluster3-thermal', 'core-cluster4-thermal'
do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,10}-thermal$', 'pinctrl-[0-9]+'
Name longer than 19 characters leads to driver probe errors when
registering such thermal zone.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull arm64 fixes from Catalin Marinas:
- Expand the speculative SSBS errata workaround to more CPUs
- Ensure jump label changes are visible to all CPUs with a
kick_all_cpus_sync() (and also enable jump label batching as part of
the fix)
- The shadow call stack sanitiser is currently incompatible with Rust,
make CONFIG_RUST conditional on !CONFIG_SHADOW_CALL_STACK
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: jump_label: Ensure patched jump_labels are visible to all CPUs
rust: SHADOW_CALL_STACK is incompatible with Rust
arm64: errata: Expand speculative SSBS workaround (again)
arm64: cputype: Add Cortex-A725 definitions
arm64: cputype: Add Cortex-X1C definitions
Get rid of unexpected unlock sparse warnings in vgic code
by adding an annotation to vgic_queue_irq_unlock().
arch/arm64/kvm/vgic/vgic.c:334:17: warning: context imbalance in 'vgic_queue_irq_unlock' - unexpected unlock
arch/arm64/kvm/vgic/vgic.c:419:5: warning: context imbalance in 'kvm_vgic_inject_irq' - different lock contexts for basic block
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240723101204.7356-4-sebott@redhat.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Add -Wno-override-init to the build flags for sys_regs.c,
handle_exit.c, and switch.c to fix warnings like the following:
arch/arm64/kvm/hyp/vhe/switch.c:271:43: warning: initialized field overwritten [-Woverride-init]
271 | [ESR_ELx_EC_CP15_32] = kvm_hyp_handle_cp15_32,
|
Signed-off-by: Sebastian Ott <sebott@redhat.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240723101204.7356-2-sebott@redhat.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Although the Arm architecture permits concurrent modification and
execution of NOP and branch instructions, it still requires some
synchronisation to ensure that other CPUs consistently execute the newly
written instruction:
> When the modified instructions are observable, each PE that is
> executing the modified instructions must execute an ISB or perform a
> context synchronizing event to ensure execution of the modified
> instructions
Prior to commit f6cc0c5016 ("arm64: Avoid calling stop_machine() when
patching jump labels"), the arm64 jump_label patching machinery
performed synchronisation using stop_machine() after each modification,
however this was problematic when flipping static keys from atomic
contexts (namely, the arm_arch_timer CPU hotplug startup notifier) and
so we switched to the _nosync() patching routines to avoid "scheduling
while atomic" BUG()s during boot.
In hindsight, the analysis of the issue in f6cc0c5016 isn't quite
right: it cites the use of IPIs in the default patching routines as the
cause of the lockup, whereas stop_machine() does not rely on IPIs and
the I-cache invalidation is performed using __flush_icache_range(),
which elides the call to kick_all_cpus_sync(). In fact, the blocking
wait for other CPUs is what triggers the BUG() and the problem remains
even after f6cc0c5016, for example because we could block on the
jump_label_mutex. Eventually, the arm_arch_timer driver was fixed to
avoid the static key entirely in commit a862fc2254
("clocksource/arm_arch_timer: Remove use of workaround static key").
This all leaves the jump_label patching code in a funny situation on
arm64 as we do not synchronise with other CPUs to reduce the likelihood
of a bug which no longer exists. Consequently, toggling a static key on
one CPU cannot be assumed to take effect on other CPUs, leading to
potential issues, for example with missing preempt notifiers.
Rather than revert f6cc0c5016 and go back to stop_machine() for each
patch site, implement arch_jump_label_transform_apply() and kick all
the other CPUs with an IPI at the end of patching.
Cc: Alexander Potapenko <glider@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Fixes: f6cc0c5016 ("arm64: Avoid calling stop_machine() when patching jump labels")
Signed-off-by: Will Deacon <will@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240731133601.3073-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The __NR_newfstat and __NR_newfstatat macros accidentally got renamed
in the conversion to the syscall.tbl format, dropping the 'new' portion
of the name.
In an unrelated change, the two syscalls are no longer architecture
specific but are once more defined on all 64-bit architectures, so the
'newstat' ABI keyword can be dropped from the table as a simplification.
Fixes: Fixes: 4fe53bf2ba ("syscalls: add generic scripts/syscall.tbl")
Closes: https://lore.kernel.org/lkml/838053e0-b186-4e9f-9668-9a3384a71f23@app.fastmail.com/T/#t
Reported-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The backlight does not work correctly with the current display panel
configuration: It works after boot, but once the display gets disabled it
is not possible to get it back on. It turns out that the ATNA45AF01 panel
needs exactly the same non-standard power sequence as implemented by the
panel-samsung-atna33xc20 driver for sc7180-trogdor-homestar.
Switch the panel in the DT to the new compatible and make two more changes
to make it work correctly:
1. Add the missing GPIO for the panel EL_ON3 line (EDP_BL_EN on CRD and
enable-gpios in the DT).
2. Drop the regulator-always-on for the panel regulator. The panel does
not seem to power off properly if the regulator stays on.
Fixes: d7e03cce04 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20240715-x1e80100-crd-backlight-v2-3-31b7f2f658a3@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
