The device has four programmable temperature alert outputs which can be
used to monitor hot or cold-junction temperatures and detect falling and
rising temperatures. It supports up to 255 degree celsius programmable
hysteresis. Each alert can be individually configured by setting following
options in the associated alert configuration register:
- monitor hot or cold junction temperature
- monitor rising or falling temperature
- set comparator or interrupt mode
- set output polarity
- enable alert
This patch binds alert outputs to iio events:
- alert1: hot junction, rising temperature
- alert2: hot junction, falling temperature
- alert3: cold junction, rising temperature
- alert4: cold junction, falling temperature
All outputs are set in comparator mode and polarity depends on interrupt
configuration.
Signed-off-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Link: https://lore.kernel.org/r/20240604133639.959682-1-dima.fedrau@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This use of the new cleanup.h scope based freeing infrastructure allows
us to exit directly from error conditions and in the good path with
the reference obtained from fwnode_find_reference() (which may be an error
pointer) automatically released.
Similarly the _scoped() version of device_for_each_child_node()
removes the need for the manual calling of fwnode_handl_put() in
paths where the code exits the loop early.
Tidy up some unusual indentation in a dev_dbg() whilst here.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20240224123215.161469-2-jic23@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MLX90635 is an Infra Red contactless temperature sensor most suitable
for consumer applications where measured object temperature is in range
between -20 to 100 degrees Celsius. It has improved accuracy for
measurements within temperature range of human body and can operate in
ambient temperature range between -20 to 85 degrees Celsius.
Driver provides simple power management possibility as it returns to
lowest possible power mode (Step sleep mode) in which temperature
measurements can still be performed, yet for continuous measuring it
switches to Continuous power mode where measurements constantly change
without triggering.
Signed-off-by: Crt Mori<cmo@melexis.com>
Link: https://lore.kernel.org/r/c6590e4fb8d993a5317b486a3e45e1bb6e9e3318.1701872051.git.cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert enum->pointer for data in the match tables, so that
device_get_match_data() can do match against OF/ACPI/I2C tables, once i2c
bus type match support added to it.
Add struct tmp11x_info and replace enum->struct *tmp11x_info for data in
the match table. Drop tmp117_identify() and simplify tmp117_probe() by
replacing device_get_match_data() and id lookup for retrieving data by
i2c_get_match_data().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230812161154.196555-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230714174628.4057920-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for MLX90615 Infra Red Thermometer, which seems to be
the predecesor of MLX90614 . There are significant differences in
the register layout compared to MLX90614, but the functionality
of the device is virtually identical.
The following differences have been identified:
- RAM/EEPROM/SLEEP access opcodes are different
- RAM/EEPROM registers are at different offsets
- EEPROM emissivity and configuration registers are at different offsets
- EEPROM configuration register bits are shuffled around
- EEPROM emissivity settings are 14 bit on MLX90615 , 16 bit on MLX90614
- MLX90615 can only ever support one sensor, MLX90614 could support two
- FIR filter is set to fixed settings on MLX90615
- IIR filter coefficients are different
This patch fills in the MLX90615 specific description and quirk handling.
The IIR filter coefficients were provided by Melexis as follows:
0b0000 - Forbidden value
0b0001 - 100% - settling time = refresh rate = 205ms (around 5Hz)
0b0010 - 50% - settling time = 2050ms (around 0.5Hz)
0b0011 - 33% - settling time = 36900ms (around 0.3Hz)
0b0100 - 25% - settling time = 5125ms (around 0.2Hz)
0b0101 - 20% - settling time = 6355ms (around 0.15Hz)
0b0110 - 17% - settling time = 7790ms (around 0.13Hz)
0b0111 - 14% - settling time = 9225ms (around 0.1Hz)
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/20230510102251.10118-6-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Factor out all the differences between MLX90614 and other similar chips
into a structure which describes the chip and allows abstracting out the
differences from the driver code. No functional change.
This patch moves all the RAM and EEPROM IO opcodes into the descriptor
structure and combines them, instead of combining the opcode and offset
in macros.
Acked-by: Crt Mori <cmo@melexis.com>
Tested-by: Crt Mori <cmo@melexis.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20230510102251.10118-5-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't error if the device-id found don't match the device-id for the
TMP117 sensor since other TMPxxx might be compatible to the TMP117. The
fallback mechanism tries to gather the required information from the
of_device_id or from the i2c_client information.
The commit also prepares the driver for adding new devices more easily
by making use of switch-case at the relevant parts.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230228090518.529811-3-m.felsch@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The current EINVAL value is more applicable to embedded library, where
user can actually put the fixed value to the sensor. In case of the
driver if the value of the channel is invalid it is better in inform
userspace that Channel was out of range as that implies more to internal
driver error than invalid input. It also makes for easier debugging of
where the error comes from during the development.
Signed-off-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/565d4df2592d751dc0f40908f2569b7c9af8e56e.1663834141.git.cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The sensor can operate in lower power modes and even make measurements when
in those lower powered modes. The decision was taken that if measurement
is not requested within 2 seconds the sensor will remain in SLEEP_STEP
power mode, where measurements are triggered on request with setting the
start of measurement bit (SOB). In this mode the measurements are taking
a bit longer because we need to start it and complete it. Currently, in
continuous mode we read ready data and this mode is activated if sensor
measurement is requested within 2 seconds. The suspend timeout is
increased to 6 seconds (instead of 3 before), because that enables more
measurements in lower power mode (SLEEP_STEP), with the lowest refresh
rate (2 seconds).
Signed-off-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/be405068f081f2d518843897b13cd0289c280b5d.1663834141.git.cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pull char/misc and other driver updates from Greg KH:
"Here is the large set of char/misc and other small driver subsystem
changes for 6.1-rc1. Loads of different things in here:
- IIO driver updates, additions, and changes. Probably the largest
part of the diffstat
- habanalabs driver update with support for new hardware and
features, the second largest part of the diff.
- fpga subsystem driver updates and additions
- mhi subsystem updates
- Coresight driver updates
- gnss subsystem updates
- extcon driver updates
- icc subsystem updates
- fsi subsystem updates
- nvmem subsystem and driver updates
- misc driver updates
- speakup driver additions for new features
- lots of tiny driver updates and cleanups
All of these have been in the linux-next tree for a while with no
reported issues"
* tag 'char-misc-6.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (411 commits)
w1: Split memcpy() of struct cn_msg flexible array
spmi: pmic-arb: increase SPMI transaction timeout delay
spmi: pmic-arb: block access for invalid PMIC arbiter v5 SPMI writes
spmi: pmic-arb: correct duplicate APID to PPID mapping logic
spmi: pmic-arb: add support to dispatch interrupt based on IRQ status
spmi: pmic-arb: check apid against limits before calling irq handler
spmi: pmic-arb: do not ack and clear peripheral interrupts in cleanup_irq
spmi: pmic-arb: handle spurious interrupt
spmi: pmic-arb: add a print in cleanup_irq
drivers: spmi: Directly use ida_alloc()/free()
MAINTAINERS: add TI ECAP driver info
counter: ti-ecap-capture: capture driver support for ECAP
Documentation: ABI: sysfs-bus-counter: add frequency & num_overflows items
dt-bindings: counter: add ti,am62-ecap-capture.yaml
counter: Introduce the COUNTER_COMP_ARRAY component type
counter: Consolidate Counter extension sysfs attribute creation
counter: Introduce the Count capture component
counter: 104-quad-8: Add Signal polarity component
counter: Introduce the Signal polarity component
counter: interrupt-cnt: Implement watch_validate callback
...
